American Standard 7143 User manual

© 2003 American Standard Inc. KS-55
DOUBLE BOWL™ SINK
SINGLE BOWL™ SINK
ENAMELED STEEL
DOUBLE BOWL KITCHEN SINK (shown)
❏7144.803 3-Hole
❏7144.804 4-Hole
❏7144.805 5-Hole
Product Features:
• Acid-resisting enameled steel
• Double bowl design
• Self-rimming installation
• Available in 3, 4 or 5 faucet hole configurations
• Silicone sealant supplied
Nominal Dimensions: 838 x 559 x 184mm
(33" x 22" x 7-1/4")
Bowl sizes:
359mm (14-1/8") wide, 413mm (16-1/4") front
to back, 178mm (7") deep
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.4M for Enameled Steel Plumbing
Fixtures
To Be Specified
❏Color: (specify White Heat,Bone, or Bisque)
❏Faucet*: (specify finish)
❏Basket Strainer: 4331.013 (Chrome only)
❏Soap Dispenser*: 4503.115 (specify color)
❏Trap:
* See faucet section for additional models available
Revised 8/02
SINGLE BOWL KITCHEN SINK
❏7143.803 3-Hole
❏7143.804 4-Hole
Product Features:
• Acid-resisting enameled steel
• Single bowl design
• Self-rimming installation
• Available in 3 or 4 faucet hole configurations
• Silicone sealant supplied
Nominal Dimensions: 635 x 559 x 184mm
(25" x 22" x 7-1/4")
Bowl sizes:
552mm (21-3/4") wide, 413mm (16-1/4") front to
back, 178mm (7") deep
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.4M for Enameled Steel Plumbing
Fixtures
ROUGHING-IN DIMENSIONS SHOWN ON REVERSE SIDE OF PAGE

© 2003 American Standard Inc. KS-56
DOUBLE BOWL™ SINK
SINGLE BOWL™ SINK
ENAMELED STEEL
311mm
(12-1/4)
838mm
(33)
102mm
(4) 102mm
(4) 102mm
(4) 102mm
(4)
559mm
(22)
*CUTOUT
NOTE
57mm
(2-1/4)
152mm
(6)
7144.804
4 HOLE
7144.805
5 HOLE
FINISHED WALL OR SPLASH BACK
38mm (1-1/2)
DIA. (TYP.)
38mm R.
(1-1/2)
OPTIONAL
13mm
(1/2) COUNTER TOP (BY OTHERS)
914mm
(36)
SUGGESTED
1-1/2 O.D. TAILPIECE
171mm
(6-3/4)
C/L
397mm
(15-5/8)
FINISHED
FLOOR
89mm
(3-1/2)
CLAMPING DETAIL
LUG AND
SCREW
ASSEMBLY
COUNTERTOP
21mm
(13/16)
MAX.
419mm
(16-1/2)
NOTES:
COUNTERTOP CUTOUT 800 x 521mm WITH 19mm RADIUS (31-1/2”x 20-1/2”WITH 3/4’
RADIUS) AT CORNERS.
PROVIDE SUITABLE REINFORCEMENT FOR WALL AND COUNTERTOP SUPPORTS.
STRAINERS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
Important: Dimensions of fixtures are nominal and may vary within the range of tolerances
established by ANSI Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility is assumed for
use of superseded or voided pages.
NOTES:
COUNTERTOP CUTOUT 597 x 521mm WITH 19mm RADIUS (23-1/2”x 20-1/2”WITH 3/4’
RADIUS) AT CORNERS.
PROVIDE SUITABLE REINFORCEMENT FOR WALL AND COUNTERTOP SUPPORTS.
STRAINERS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
Important: Dimensions of fixtures are nominal and may vary within the range of tolerances
established by ANSI Standard A112.19.4
These measurements are subject to change or cancellation. No responsibility is assumed for use
of superseded or voided pages.
CLAMPING DETAIL
LUG AND
SCREW
ASSEMBLY
COUNTERTOP
21mm
(13/16)
MAX.
311mm
(12-1/4)
635mm
(25)
318mm
(12-1/2)
102mm
(4) 102mm
(4)
559mm
(22)
152mm
(6)
7143.804
4 HOLE
FINISHED WALL OR SPLASH BACK
38mm R.
(1-1/2)
C/L
OPTIONAL
13mm
(1/2) COUNTER TOP (BY OTHERS)
171mm
(6-3/4) 914mm
(36)
SUGGESTED
1-1/2 O.D.
TAILPIECE
FINISHED
FLOOR
102mm
(4)
57mm
(2-1/4)
38mm (1-1/2)
DIA. (TYP.)
89mm
(3-1/2)
*CUTOUT
NOTE
7144.803/804/805
7143.803/804