Crosswater Heir 18-31 User manual

Installation Instructions
Adjustable
wrench
Channel
locks
Plumbers’ putty
or caulking
Flat head
screwdriver
Cross head
screwdriver
Hexagonal
key
Heir Handshower Rail Set
18-31 / 18-30
Introduction
Installation notes
This product has been fully inspected throughout the production
process and only leaves our factory after a 15-step QC process.
This handshower set is supplied with a mixed hot and cold water
feed. Please ensure that the mixer that supplies this handset has had
its hot and cold water pressures balanced, otherwise the handset will
not function correctly.
The minimum water pressure required for this handset is 20 psi. The
maximum water pressure is 60 psi, beyond which pressure-reducing
valves must be fitted.
IMPORTANT: Please read these instructions carefully before
beginning and retain for future reference.
Before beginning installation, check for any damage that may have
occurred during transport. Note: Damage claims cannot be made
during or after installation.
Improper installation shall result in loss of warranty in case of
damage caused by impacts or rubbing against rough surfaces.
We do not accept responsibility for any problems that may occur
through incorrect installation.
Dimensions
Tools required
29-3/4"
Ø3/4"
Ø1-1/4"
2-5/8"
2-5/8"
3-1/4"
2-1/4"
The installation must comply with all plumbing codes including local
codes and be installed by a licensed plumbing contractor.
Before installing a new faucet it is essential that the supply pipes are
thoroughly flushed in order to remove any remaining debris, solder
or other impurities. Failure to carry out this simple procedure can
cause problems or damage to the working of the faucet.
Installing shut-off valves on incoming supply lines is recommended
for ease of maintenance.
Turn off the main water supply before connecting to any existing
pipework or doing any maintenance.
IMPORTANT! Please check for any hidden pipes and cables,
electric or otherwise, before drilling holes in a wall or floor.

HANDSHOWER
WASHER
HOSE
BRACKET
COVER
PLATE
SEALS




Installation
CAP
SCREW
ANCHOR
FIXING SCREW
CAP
SCREW
Issue date: 19072021
Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact: Crosswater London , 393 Fortune Blvd., Milford, MA 01757 www.crosswaterlondon.com
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone] email: [e-mail]
Install the bracket on to the rail and fit the screw covers.
Position the fixing base, mark the wall and drill holes. Insert
the anchors into the holes.
Secure the cover plate and rail by using the screws provided,
then put on the cap.
Connect the shower hose to the wall outlet (sold separately),
and insert the handshower into the holder.
3 Cleaning Instructions
Rinse away any traces of soap and gently dry with a
clean, soft cloth after each use. Rinse completely with
water and dry any overspray. This will maintain the
finish and avoid water spotting.
To remove mineral deposits, use a 50/50 solution of
white vinegar and water. Do not allow the solution to
soak on the product. Simichrome Polish® contains a
protective film to enhance maintenance and is helpful
in preventing water spot buildup. Follow instructions
to ensure optimum results.
Never use an abrasive material such as a brush or
scouring pad to clean the surface. The use of abrasive
cleaners, cleansers or disinfectants will alter the surface
finish and void the warranty.
Do not allow certain materials such as toothpaste,
cologne, shaving cream, nail polish remover, vinegar,
wine, drain and glass cleaners to remain on the surface.
Prolonged contact will alter surface finishes and void
the warranty.
We DO NOT recommend using any household
cleaners as many can cause damage to the finish.
Please see the website for care instructions for specific
finishes.