American Standard Selectronic 6055.102 User manual

FAQ'S
Q: How will I know if battery needs to be replaced?
A: Valve does not open and sensor blinks 2 times
interrupted by pause for up to 7 days.
Q: Why has the flow rate of the faucet reduced
significantly?
A: Check and clean aerator and strainer.
Q: There is no flow out of faucet when I'm in the
sensor range?
A: Check sensor. If sensor blinks 2 times interrupted
by pause, replace battery, or call 1800-442-1902.
Q: Why does the faucet operate the opposite of
expected-Turns On when not in sensor range, but
turns off when in sensor range?
A: Sensor wires to solenoid are reversed. Black to -
& Red to + is correct.
Q: What is the normal operating pressure range?
A: Faucet will operate with supply pressures ranging
from 20-80 psi.
9
8
1. Remove ENCLOSURE COVER.
2. Close SUPPLY STOP (5) with 4mm Hex wrench.
Note: Keep water flowing out of faucet while shutting off.
3. Pull off Red (1) and Black (2) CONNECTORS from
SOLENOID VALVE (3).
4. Unthread STRAINER (4) using a 7/16" socket.
5. Pull out the STRAINER (4) and clean with an old
toothbrush. Rinse thoroughly with water.
6. Install the STRAINER (4) back in its place and
tighten with a 7/16" socket.
Caution: do not over tighten strainer.
Note: It is recommended to clean strainer every 6
months.
7. Replace ENCLOSURE COVER. Tighten cover
screws firmly.
1. Remove AERATOR HOUSING (1) with KEY
supplied with faucet.
3. Remove AERATOR (2) from HOUSING (1).
2. Clean the AERATOR SCREENS (3) with a old tooth
brush to remove dirt.
4. Rinse Clean with water. Reassemble and install into
spout end. Be sure black seal washer is in place.
4
4
3
2
15
CLEAN
SCREENS
HOW TO CLEAN FILTER; Fig. 4
4
HOW TO CLEAN AND REMOVE
THE AERATOR; Fig. 5
5
Fig.4
2
3
Fig.5
CAUTION Before opening ENCLOSURE
disconnect AC power supply.
1
CAUTION
GENERAL CLEANING; Fig. 7
1. For general cleaning use a damp, soft cloth to clean
the spout and the sensor.
2. For cleaning dirt use a soft cloth with diluted dish
washing detergent. Wipe the area using a wet cloth
and dry using a soft cloth.
Do not scratch the sensor when cleaning.
Avoid using anything that may scratch the spout
surface. Never use polishing power, detergent or a
nylon scrub brush. They will damage the surface of the
spout or Sensor.
7
Fig.7
Fig.5
HOW TO CONVERT RIGID GOOSE
NECK SPOUT TO SWING SPOUT
Fig. 6
The GN SPOUT is shipped from the factory as a
rigid assembly. To convert the GN SPOUT into a
SWING SPOUT proceed as follows:
1. Remove SET SCREW (1) from back of GN SPOUT
(2) with a flat blade screwdriver. Fig. 6.
2. Install SWIVEL SET SCREW (3) into opening in the
GN SPOUT (2). SWIVEL SET SCREW (3) is found in
hardware bag within product box.
6
Fig.6
1
2
3(USE SHORT
SET SCREW
FOR SWIVEL
SPOUT)
605P400
605P800
10
M968809 Rev.1.2 M968809 Rev.1.2
SELECTRONIC
LAVATORY FAUCETS
CHROME 002
Replace the "YYY" with
appropriate finish code
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2005
A923672-0070A
FAUCET SUPPLY
HOSE
M962411-0070A
MOUNTING KIT
A913202-0070A
WASHER
M962387-0070A
MOUNTING SCREW KIT
M950250-0070A
DC SOLENOID
VALVE ASSEMBLY
M950251-0070A
AC SOLENOID
VALVE ASSEMBLY
A922272-0070A
U GROMMET
A922251-0070A
SOLID GROMMET
A924162-0070A
SUPPLY HOSE
044912-0070A
MOUNTING NUT
M962388-0070A
SENSOR KIT
M923827-YYY0A
2.2 GPM AERATOR
066508-YYY0A
0.5 GPM AERATOR
6055.102
6055.105
6056.102
6056.105
6057.102
6057.105
Cast Spout
PRODUCT NUMBERS
Cast Spout
6055.153
6055.155
6056.153
6056.155
6057.153
6057.155
5-1/4" GN Spout
6055.163
6055.165
6056.163
6056.165
6057.163
6057.165
6" GN Spout
A922267-0070A
ROUND GROMMET
A923654-0070A
BATTERY 6VCR-P2
A950487-0070A
CIRCUIT BOARD DC
A950489-0070A
CIRCUIT BOARD
AC & MULTI AC
A922290-0070A
POWER SUPPLY
GROMMET
M950169-0070A
POWER SUPPLY
M962389-0070A
SOLENOID & SCREWS
A950507-0070A
FILTER
A950509-0070A
SUPPLY STOP
A918462-0070A
SOLENOID SCREWS
A922265-0070A
10 ft. MULTI EXTENSION WIRE
(for 6057 series only)
A950223-007L0A
SENSOR