American Standard Instanto 3.5 GPF Elongated Flush Valve Toilet... User manual

M61
© 2006 American Standard Inc.
To Be Specied:
❏ Color: ❏ White
❏ Seat: Olsonite #95 open front seat less cover
❏ Seat: Church #9500C open front seat less cover
❏ Seat: Pressalit seats for American Standard,
open front seat with/without cover (thermoset
compound material).
❏ Alternate Seat:
❏ Flush Valve: Sloan Royal #110-3 (Top Spud)
Sloan Royal #144-3 (Back Spud)
❏ Alternate Flush Valve:
❏ Carrier Fitting (by others):
INSTANTO™ 3.5 GPF
ELONGATED FLUSH VALVE TOILET
VITREOUS CHINA
INSTANTO™ ELONGATED 3.5 GPF TOILET
• Elongated ush valve toilet
• Vitreous china
• Wall-mounted elongated bowl
• Blowout ush action
• Fully-glazed 2-5/8" trapway
• 1-1/2" inlet spud
• 100% factory ush tested
❏ 2512.010 Elongated bowl only, top spud
❏ 2511.012 Elongated bowl only, back spud
❏ 2513.018 Elongated bowl only, back spud
with Integral Seat
Component parts:
❏ 047007-0070A Inlet spud (furnished with bowl)
Nominal Dimensions:
660 x 356 x 381mm
(26" x 14" x 15")
Recommended working pressure–between
25 psi at valve when ushing and 80 psi static
Fixture only, less seat, bolt caps and ush valve
Blowout water closets are exempt from the 1.6
gallon per ush requirements of the National Energy
Policy Act. However, some state and local codes
do not allow the use of 3.5 gallons per ush toilets.
Check local codes.
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.2 for Vitreous China Fixtures
BARRIER FREE
SEE REVERSE FOR ROUGHING-IN DIMENSIONS
Revised 4/07
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE
BUILDING FACILITIES - CHECK LOCAL CODES.
When installed so top of seat is 432 to 483mm (17" to 19") from the
finished floor.

M62
© 2006 American Standard Inc.
INSTANTO™ 3.5 GPF
ELONGATED FLUSH VALVE TOILET
VITREOUS CHINA
BARRIER FREE
2512.010
2511.012
470mm
(18-1/2)
660mm
(26)
C/L OF SEAT POST HOLES
140mm
(5-1/2) CENTERS
292mm
(11-1/2)
14mm
(9/16)
76mm
(3)
133mm
(5-1/4)
356mm
(14)
318mm
(12-1/2)
229mm
(9)
98mm
(3-7/8)
70mm
(2- 3/4)
C/L OF FLUSH VALVE
38mm
(1-1/2) FINISHED FLOOR
381mm
(15)
1-1/2 SPUD
159mm
(6-1/4)
298mm
(11-3/4)
121mm
(4-3/4)
1" N.P.T. OR C.W.T.
SUPPLY TO
FLUSH VALVE
(3) 25mm (1) DIA.
HOLES FOR
CARRIER STUDS
C/L OF OUTLET
673mm
(26-1/2)
6mm
(1/4)
FINISHED WALL
381mm
(15)
159mm
(6-1/4)
695mm
(27-3/8)
FINISHED
FLOOR
298mm
(11-3/4)
17mm
(11/16)
133mm
(5-1/4)
98mm
(3-7/8)
79mm
(3-1/8)
FINISHED
WALL
470mm
(18-1/2)
C/L OF SEAT POST HOLES
140mm (5-1/2) CENTERS
581mm
(22-7/8)
356mm
(14)
C/L
38mm (1-1/2) DIA. HOLE IN WALL
95mm
(3-3/4)
FOR WALLS UP TO 25mm (1") IN THICKNESS;
FOR EACH 25mm (INCH) ADDITIONAL THICKNESS
OF WALL ADD 25mm (1") TO THIS DIMENSION
121mm
(4-3/4)
254mm
(10)
16mm
(1-5/8)
38mm
(1-1/2)
102mm
(4)
(3) 78mm (1) DIA. HOLES
FOR CARRIER STUDS
C/L OF 1" C.W.T. OR N.P.T. SUPPLY
AS REQ'D TO FLUSH VALVE
INLET
38mm
(1-1/2)
298mm
(11-3/4)
127mm
(5)
286mm
(11-1/4)
114mm
(4-1/2)
114mm
(4-1/2)
C/L OF
OUTLET
76mm (3) DIA. HOLE
IN WALL FOR 1-1/2" SPUD
NOTES:
WASTE OUTLET SEAL RING MUST BE NEOPRENE OR GRAPHITE-
FELT (WAX RING NOT RECOMMENDED).
TO COMPLY WITH AREA CODE GOVERNING THE HEIGHT OF VACUUM
BREAKER ON FLUSH VALVE, THE PLUMBER MUST VERIFY
DIMENSIONS SHOWN FOR SUPPLY ROUGHING.
SUGGEST 1/16" CLEARANCE BETWEEN FACE OF WALL AND BACK OF
BOWL.
METHOD AND MEANS OF SUPPORT TO BE FIGURED AND FURNISHED
BY OTHERS.
FLUSH VALVE NOT INCLUDED WITH FIXTURE AND MUST BE
ORDERED SEPARATELY.
PLUMBER NOTE: PROVIDE SUITABLE REINFORCEMENT FOR ALL
SUPPORTS.
IMPORTANT: Dimensions of xtures are nominal and may vary within
the range of tolerances established by ANSI Standard A112.19.2. These
measurements are subject to change or cancellation. No responsibility is
assumed for use of superseded or voided pages.
Revised 5/06