AMP RF 2W Operating instructions

Upgrade to the industry’s most advanced Motor Program:
AMP™Motorization features 2-way technology with superior value
and innovation paired with a smart, seemless user interface.
Specifications
•Wall Switch is cut into the wall and mounts like
a standard wall switch
•LCD Display with up to 15 channels wall switch
•Channel 0 controls all shades assigned to wall switch;
ability to hide extra channels
•Favorite position activated by quick touch of a button
•Locking feature prevent unwanted configuration changes
RF 2W 15 Channel Wall Switch
Programming Guide
AMP 2 color logo: PMS Cool Gray 2 & PMS 306 Blue

AMP 2 color logo: PMS Cool Gray 2 & PMS 306 Blue
AMP™WALL SWITCH |PROGRAMMING GUIDE
2
Declarations
Safety Instructions
AMP™Wall Switch Overview
AMP™Wall Switch Functions
P1 Button Instructions
Initial Set-up
Adjust Limits
Favorite Position
Add or Remove Additional Wall Switch
Adjust Motor Speed
Roller or Sheer Mode
Quick Index
Troubleshooting
3
4
5
6
7
8
9
10
11
12
13
14
14
AMP™Motorization Table of Contents
Please scan QR code to watch videos
for product programming

AMP™WALL SWITCH |PROGRAMMING GUIDE
3
Declarations
U.S. Radio Frequency FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation
of the device. Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.

AMP25B
Instruction
Attention
-1-
The motor is suitable for motorization of roller blinds, sheer shadings, roman shades, and zebra shades.
Never drop, knock, drill or submerge the motor. Keep the power cable in right position as following.
Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.
Declarations
Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.
-2-
Safety
1. Do not expose motor to humid, damp or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna and keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If power cable or connector is damaged, do not use.
6. Ensure correct crown and drive adaptor are used.
7. Ensure power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls shall be properly isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered
operation.
11. Installation and programming to be performed by a qualified professional, use or modification outside
the scope of this instruction may void warranty.
Features
Fields of Application
Specifications
Following data for reference
Working temperature: -10℃ ~ +50℃
Input Voltage: USB 5V 1A / USB 5V 2A
Radio Frequency: 433.925MHz
Maximum Running Time: 6 minutes
Model Rated Torque
(N.m)
Rated Speed
(rpm)
Rated Power
(W)
AMP25B - 0.7/34 0.7 34 8
AMP25B -1.1/28 1.1 28 8
Charging Instructions
This motor has a built in Li-ion battery pack with integrated charge management.
Max power input for recharging: 5V 2A.
Before first use please charge motor for 6 hours. Using 5V charger (most phones charger is 5V ) .
During operation, when the motor starts, the buzzer will beep 10 times, indicating a low-voltage alarm and
needs to be charged.
During operation, the voltage was detected to be too low, the battery was about to run out, the battery stopped
running and needed to be recharged.
Rechargeable Battery
Blinking red:
Low battery alert
Blinking green:
Charging is processing
Solid green:
Battery has
finished charging.
FCC Text - text 01
Add A zoom in on the
charging port
P1 Button Instructions
P1 button
Lithium Battery Switch
LED light
Micro-USB Port
Add visual explanation of P1 - file 02
Sheer
Roller Revolve Roman shades
Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.
AMP™WALL SWITCH |PROGRAMMING GUIDE
4
Safety Instructions
Important Safety Instructions
Attention
1. Do not expose motor to humid, damp, or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna. Keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If the power cable or connector is damaged, do not use.
6. Ensure the correct crown and drive adapter are used.
7. Ensure the power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls should be properly isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.
11. Installation and programming should be performed by a qualified professional. Use or modification outside the scope of these instructions may void warranty.
Never drop, knock, drill or submerge the motor. Keep the power cable in the proper position as shown below.
Read all safety instructions before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.
× ×× ×

Roller Cellular/Honeycomb
Standard
Sheer Cellular/Honeycomb
Skylight
Banded
Tilt-Only
Horizontal
Roman
AMP™WALL SWITCH |PROGRAMMING GUIDE
5
AMP™Wall Switch Overview
1. Fields of Application
2. Specification
3. Wall Switch Instructions
4. Replace/Install Battery
a. Gently take out the battery cover.
b. Install 2 x AAA batteries with positive (+) side facing up.
c. Gently assemble the battery cover back.
Voltage 3V (AAA Battery x 2)
Radio Frequency 433.92 MHz Bi-directional
Transmitting Power 10 milliwatt
Operating Temperature 14°F to 122°F (-10°C to 50°C)
RF Modulation FSK
Lock Function Yes
IP Rating IP20
Transmission Distance up to 200m (outdoor)
Narrow
Shade
AMP25B
Instruction
Attention
-1-
The motor is suitable for motorization of roller blinds, sheer shadings, roman shades, and zebra shades.
Never drop, knock, drill or submerge the motor. Keep the power cable in right position as following.
Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.
Declarations
d electrical products appropriately.
-2-
Safety
1. Do not expose motor to humid, damp or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna and keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If power cable or connector is damaged, do not use.
6. Ensure correct crown and drive adaptor are used.
7. Ensure power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls shall be properly isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered
operation.
11. Installation and programming to be performed by a qualified professional, use or modification outside
the scope of this instruction may void warranty.
Features
Fields of Application
Specifications
Following data for reference
Working temperature: -10℃ ~ +50℃
Input Voltage: USB 5V 1A / USB 5V 2A
Radio Frequency: 433.925MHz
Maximum Running Time: 6 minutes
Model Rated Torque
(N.m)
Rated Speed
(rpm)
Rated Power
(W)
AMP25B - 0.7/34 0.7 34 8
AMP25B -1.1/28 1.1 28 8
Charging Instructions
This motor has a built in Li-ion battery pack with integrated charge management.
Max power input for recharging: 5V 2A.
Before first use please charge motor for 6 hours. Using 5V charger (most phones charger is 5V ) .
During operation, when the motor starts, the buzzer will beep 10 times, indicating a low-voltage alarm and
needs to be charged.
During operation, the voltage was detected to be too low, the battery was about to run out, the battery stopped
running and needed to be recharged.
Rechargeable Battery
Blinking red:
Low battery alert
Blinking green:
Charging is processing
Solid green:
Battery has
finished charging.
FCC Text - text 01
Add A zoom in on the
charging port
P1 Button Instructions
P1 button
Lithium Battery Switch
LED light
Micro-USB Port
Add visual explanation of P1 - file 02
Sheer
Roller Revolve Roman shades
Button Instructions
LOWER
CHANNEL
HIGHER
CHANNEL
BATTERY
DOWN
(P2)(P2)
STOP
UP
n
-
0 
 
Q
�
 
Advanced setting - disable limit setting
Channel option
One-Way
Left Stack
One-Way
Right Stack
Two-Way
Split Stack
*For AMP™ Drapery, press "Up" for open; press "Down" for close.

AMP™WALL SWITCH |PROGRAMMING GUIDE
6
AMP™Wall Switch Function
1. Channel Options
Select A Channel
a. Press “<” button on the wall switch to select a lower
channel.
b. Press “>” button on the wall switch to select a higher
channel.
Hide Unused Channels
a. Press and hold (about 3 sec) “<” and “>” buttons
simultaneously until wall switch displays “C” (channel).
b. Press “<” or “>” button to select required quantity of
channel (between 1 to 15).
c. Press “Stop” button to confirm selection (the example
shows a 5-channel selection). The LED will display “O” (OK)
once to confirm selection.
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Wall Switch
Response
Wall Switch
Response
Wall Switch
Response
a.
a.
b.
b.
c.
+ or
Higher
Channel
Higher
Channel
Lower
Channel
Lower
Channel
Higher
Channel
Higher
Channel
Stop
2. Advanced Setting - Disable Limit Setting
a. Press and hold “Stop“ button more than 15s,
WS will show “L” (lock), WS is now in “Lock” mode and
following commands are disabled:
- Change Motor Direction
- Setting the Upper and Lower Limit
- Adjust Limit
- Roller Mode or Sheer Mode
b. Press and hold “Stop“ button more than 15s,
WS will show “U” (unlock) - back to unlock mode, you can
assess all control functions.
*This advanced feature is intended to be used after all
shade programming is completed. User Mode will prevent
accidental or unintended changing of limits.
n
-
0 
 
Q
�
 


more than 


is displayed

L
:_< ) •
 
 
Lock status
Unlock status
Advanced setting - disable limit setting
Channel option
n
-
0 
 
Q
�
 


more than 


is displayed

L
:_< ) •
 
 
Lock status
Unlock status
Advanced setting - disable limit setting
Channel option
n
-
0 
 
Q
�
 


more than 


is displayed

L
:_< ) •
 
 
Lock status
Unlock status
Advanced setting - disable limit setting
Channel option
Lower
Channel
n
-
0 
 
Q
�
 


more than 


is displayed

L
:_< ) •
 
 
Lock status
Unlock status
Advanced setting - disable limit setting
Channel option
n
-
0 
 
Q
�
 


more than 


is displayed

L
:_< ) •
 
 
Lock status
Unlock status
Advanced setting - disable limit setting
Channel option
Higher
Channel
n
-
0 
 
Q
�
 


more than 


is displayed

L
:_< ) •
 
 
Lock status
Unlock
status
Advanced setting - disable limit setting
Channel option

P1 Button
Micro-USB Port
LED light
Power line
Signal line
P1 Button
AMP™WALL SWITCH |PROGRAMMING GUIDE
7
P1 Button Instructions
1
2
3
4
5
Test Motor
1
2
6
10
14
Activate Pairing Mode
Sleep Mode
Reverse Direction
Reset To Factory Settings
Approx. 2 sec.
Happening as you press for 2 seconds
Happening as you press for 1 second
Happening as you press for 6 seconds
Happening as you press for 10 seconds
Happening as you press for 14 seconds
when released
when released
when released
when released
when released
Approx. 6 sec.
Approx. 10 sec.
Approx. 14 sec.
Until Shade:
Until Shade:
Motor Response:
Motor Response:
Motor Response:
Until Shade:
Until Shade: Motor Response:
Less than 1 sec.
Press P1
Press P1
Press P1
Press P1
Press P1
Motor Response: Wakes & Runs
Beep x1
Beep x2
Beep x3
Beep x4
Jog x3
Jog x4
Jog x1
Jog x2
2. P1 Button Instruction
2. P1 Button Location
AMPCEL and AMPTILT motors DO NOT BEEP
AMPTILT AMP25B / AMP28B / AMP25BDC AMPCELAMP35B
RJ45
P1 Button
LED
Antenna Hole
AMP DRAPERY MOTOR
P1 Button
LED light
P1 button
Lithium Battery Switch

AMP™WALL SWITCH |PROGRAMMING GUIDE
8
Initial Set-up
1. Pair / Unpair Wall Switch
2. Change Motor Direction (if necessary)
3. Setting the Upper and Lower Limits
Press “Up” or “Down” button to check if the shade moves
in the desired direction.
If you need to reverse the direction, press and hold (about 2
sec) “Up” and “Down” buttons simultaneously until motor
jog x1 and beep x1.
Set Upper Limit
a. Press “Up” button to raise the shade, then press “Stop”
button when it is in the desired upper limit.
b. Press and hold (about 5 sec) “Up” and “Stop” buttons
simultaneously until motor jog x2 and beep x3.
Set Lower Limit
a. Press “Down” button to lower the shade, then press
“Stop” button when it is in the desired lower limit.
b. Press and hold (about 5 sec) “Down” and “Stop” buttons
simultaneously until motor jog x2 and beep x3.
a. Press “P1” button (about 2 sec) on the motor head until
motor jog x1 and beep x1.
b. In the next 10 secs, press and hold “Stop” button on the
Wall Switch until motor jog x2 and beep x3.
* Repeat the same procedure to unpair Wall Switch.
*The operation is only valid when there are no limits. If the
motor has already set the upper and lower limit, then you
can only switch direction by pressing P1 button (See P1
button instructions).
*If you exit the limit setting status before you finish the limit
settings, the motor will take the previous existing limits.
Action on
Wall Switch
Action on
Motor
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Motor Response
Motor Response
Motor Response
Motor Response
Motor Response
b.
a.
a.
a.
b.
b.
+
+
+
Jog x2
Jog x2
Jog x1
Jog x1 Beep x1
Jog x2 Beep x3
Beep x3
Beep x3
Beep x1
Stop
Up
Up Up Stop
Stop
Down
Down Down
AMPCEL and AMPTILT motors DO NOT BEEP
P1P1
P1 P1
P1

AMP™WALL SWITCH |PROGRAMMING GUIDE
9
Adjust Limits
1. Adjust the Upper Limit
a. Press and hold (about 5 sec) “Up” and “Stop” buttons
simultaneously until motor jog x1 and beep x1.
b. Use “Up” button to raise the shade to the desired highest
position, and use “Up” or “Down” button to do the final
adjustment if necessary.
c. Press and hold (about 5 sec) “Up” and “Stop” buttons
simultaneously until motor jog x2 and beep x3.
2. Adjust the Lower Limit
a. Press and hold (about 5 sec) “Down” and “Stop” buttons
simultaneously until motor jog x1 and beep x1.
b. Use “Down” button to lower the shade to the desired
lowest position, and use “Up” or “Down” button to do the
final adjustment if necessary.
c. Press and hold (about 5 sec) “Down” and “Stop” buttons
simultaneously until motor jog x2 and beep x3.
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Motor Response
Motor Response
Motor Response
Motor Response
a.
a.
c.
c.
b.
b.
+
+
+
+
Stop
Stop
Stop
Stop
Up
Down
Up
Down
Jog x1
Jog x1
Jog x2
Jog x2
Beep x1
Beep x1
Beep x3
Beep x3
Up
Down

AMP™WALL SWITCH |PROGRAMMING GUIDE
10
Favorite Position
3. Delete Favorite Position
a. Press one “P2” button until motor jog and beep x1.
b. Press “Stop” button until motor jog and beep x1.
c. Once more, press “Stop” button until motor jog x1 and
long beep x1.
1. Set Favorite Position
a. Use “Up” or “Down” button to move the shade to desired
Favorite position.
b. Press one “P2” button on the back of Wall Switch until
motor jog x1 and beep x1.
c. Press “Stop” button until motor jog x1 and beep x1.
d. Once more, press “Stop” button until motor jog x2 and
beep x3.
2. Send Shade to Favorite Position
Press and hold (about 2 sec) “Stop” button, motor will move
to Favorite position.
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Motor Response
Motor Response
Motor Response
Motor Response
Shade Response
a.
a.
b.
b.
d.
c.
c.
or
or
or
DownUp
Jog x1
Jog x1
Jog x2
Jog x1
Jog x1
Jog x1
Beep x1
Beep x1
Beep x3
Beep x1
Beep x1
Beep x1
Stop
Stop
Stop
Stop
Stop
P2 Button
P2 Button

AMP™WALL SWITCH |PROGRAMMING GUIDE
11
Add or Remove Additional Wall Switch
1. Using Current Wall Switch
a. On the current Wall Switch, press one “P2” button until
motor jog x1 and beep x1.
b. Once more, on the current Wall Switch, press one “P2”
button until motor jog x1 and beep x1.
c. On the New Wall Switch, press one “P2” button until
motor jog x2 and beep x3.
2. New Wall Switch
Follow instructions on page 8 under the section Pair /
Unpair Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Motor Response
Motor Response
a. b.
c.
Jog x1Jog x1
Jog x2
Beep x1Beep x1
Beep x3
*Repeat the same procedure to remove additional Wall
Switch.
P2 Button
P2 Button
P2 Button

AMP™WALL SWITCH |PROGRAMMING GUIDE
12
Adjust Motor Speed
1. Acceleration Speed
a. Press one “P2” button until motor jog x1 and beep x1.
b. Press “Up” button until motor jog x1 and beep x1.
c. Once more, press “Up” button until motor jog x2 and
beep x1.
2. Deceleration Speed
a. Press one “P2” button until motor jog x1 and beep x1.
b. Press “Down” button until motor jog x1 and beep x1.
c. Once more, press “Down” button until motor jog x2 and
beep x1.
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Motor Response
Motor Response
Motor Response
Motor Response
a.
a.
b.
b.
c.
c.
Jog x1
Jog x1
Jog x2
Jog x2
Jog x1
Jog x1
Beep x1
Beep x1
Beep x1
Beep x1
Beep x1
Beep x1
*If the motor has no response, it already has a Maximum or
Minimum speed.
Up
Down
Down
Up
P2 Button
P2 Button

AMP™WALL SWITCH |PROGRAMMING GUIDE
13
Roller or Sheer Mode
1. Roller Shade Mode - continue movement
after a short press - Default Mode
a. Press and hold (about 5 sec) “Up” and “Down” buttons
simultaneously until motor jog x1.
b. Press and hold (about 2 sec) “Stop” button until motor
jog x2 and beep x3.
2. Sheer Shade Mode - jog movement after a
short press (continue movement after a long
press)
a. Press and hold (about 5 sec) “Up” and “Down” buttons
simultaneously until motor jog x1.
b. Press and hold (about 2 sec) “Stop” button until motor
jog x1 and beep x1.
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Action on
Wall Switch
Motor Response
Motor Response
Motor Response
Motor Response
a.
a.
b.
b.
+
+
Down
Down
Up
Up
Jog x1
Jog x1
Jog x2
Jog x1
Beep x3
Beep x1
Stop
Stop

Issues Possible Causes Solution
Battery in motor is depleted Recharge with compatible AC adapter and check connection and positioning of solar PV panel
Insufficient charging from Solar PV Panel Check connection and orientation of solar PV panel
Wall Switch battery is discharged Replace battery
Battery is inserted incorrectly into Wall Switch Check battery polarity
The motor has no response Radio interference / shielding Ensure Wall Switch and the antenna on the motor are positioned away from metal objects
Receiver distance is too far from Wall Switch Move Wall Switch to a closer position
Power failure Check power supply to motor is connected and active
Incorrect wiring Check that wiring is connected correctly (refer to motor installation instructions)
Motor beeps 10 times when
in use Battery voltage is low / PV (solar panel issue) Recharge with AC adapter or check connection and positioning of solar PV panel
Always reserve an individual channel for programming functions
SYSTEM BEST PRACTICE - Provide an extra 15 channel wall switch in your multi-motor projects that
provides individual control for each motor for programming purposes
Place all other motors into sleep mode (ref to P1 button instructions)
Cannot program a single
motor (multiple motors
respond)
Multiple motors are paired to the same channel.
AMP™WALL SWITCH |PROGRAMMING GUIDE
14
Troubleshooting
Turnils Contact Information
Turnils North America
1750 Satellite Blvd, Suite 100
Buford, GA 30518
1-800-341-3600
[e-mail]
Turnils Canada
2908 Portland Drive
Oakville, Ontario L6H 5W8
1-800-341-3600
[e-mail]
Quick Index
Settings Steps
1 Pairing P1 (hold down for 2s) >Stop (hold down for 2s)
2 Switch Rotating Direction Up + Down (hold down for 2s)
3 Setting Upper & Lower Limits
4 Add / Remove Favorite Position P2 >Stop >Stop
5 Roller Mode & Sheer Mode Switch Up + Down (hold down for 5s) >Stop
6 Adjust Limits
7 Pair / Unpair Additional Emitter P2 (existing) >P2 (existing) >P2 (new)
8 Speed Regulation
Upper Limit: Up (hold down for 2s) >Up + Stop (hold down for 2s)
Upper Limit: Up + Stop (hold down for 5s) >Up or Down >Up + Stop (hold down for 2s)
Acceleration: P2 >Up >Up
Lower Limit: Down (hold down for 2s) >Down + Stop (hold down for 2s)
Lower Limit: Down + Stop (hold down for 5s) >Up or Down >Down + Stop (hold down for 2s)
Deceleration: P2 >Down >Down