Ampak WDSB-686GN Mounting instructions

AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information
Doc. NO:
AMPAK
WSDB-686GN
Hardware & Software Setup Guide
Rev. 0.2

AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information
Doc. NO:
1
1. WLAN Function Quick Start Guide
Physical hardware configuration likes as figure1. Please follow the following procedure step by
step to get starting WLAN function.
Software setup:
Follow driver installation procedure steps to install the GB9662 driver on your PC (OS: XP).
 1-1.Copy
WDSB-686GN\WSDB-686GN_Driver_V1.2_10122012\Nvram\GB9662_NVRAM_V1.1_09132
012.TXT to C:\Windows\system32\Drivers
1-2. Copy
WDSB-686GN\WSDB-686GN_Driver_V1.2_10122012\5_90_153_49_43362_mfg_A2(Driver)\A
pps\ wl.exe to C:\Windows\system32\
 1-3.In Device Manager, choose SDA Standard Compliant SD Host Controller and click right button of
mouse and then choose Update driver
SDIO Board
Test Board
Socket

AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information
Doc. NO:
2
 1-4.Choose No, not now, and then click Next.
 1-5.Choose install from a list or specific location (Advanced), and then click Next.

AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information
Doc. NO:
3
 1-6.Choose Don’t search, I will choose driver to install, and then click Next .
 1-7.Click Have Disk .

AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information
Doc. NO:
4
 1-8.Click Browse to choose correct directory of Driver
WDSB-686GN\WSDB-686GN_Driver_V1.2_10122012\5_90_153_49_43362_m
fg_A2(Driver) \bcmsddhd.inf and then click OK to next step.
 1-9.Choose Broadcom 802.11g Network Adapter and click Next to install driver.

AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information
Doc. NO:
5
 1-10.Click Finish and you can check the device is working fine in Device Manager.
 1-11.In Device Manager, Choose Broadcom 802.11g Network Adapter and click
right button of mouse and then choose content.

AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information
Doc. NO:
6
 1-12.In the tab of Advanced, choose
 1-13.In the tab of Advanced, choose 43362ROMImagePatch item and replace with
\SystemRoot\system32\drivers\ GB9662_NVRAM_V1.1_09132012.TXT and
then click OK button.

AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information
Doc. NO:
7
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void
the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
RF Exposure Information (SAR)
This device meets the government’s requirements for exposure to radio waves. This device is
designed and manufactured not to exceed the emission limits for exposure to radio frequency
(RF) energy set by the Federal Communications Commission of the U.S. Government.
The exposure standard employs a unit of measurement known as the Specific Absorption Rate,
or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted using standard
operating positions accepted by the FCC with the EUT transmitting at the specified power level in
different channels.
The highest SAR value for the device as reported to the FCC is 0.395 W/kg when placed next to
the body.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed
such that 20cm may be maintained between the antenna and users. The final end product must
be labeled in a visible area with the following: "Contains FCC ID: 2AAD3AA1G0J0 ”

AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information
Doc. NO:
8
Information for the OEMs and Integrators
The following statement must be included with all versions of this document supplied to an
OEM or integrator, but should not be distributed to the end user.
1) This device is intended for OEM integrators only.
2) Please see the full Grant of Equipment document for other restrictions.