Panasonic AW-PB305AN User manual

Before attempting to connect, operate or adjust this product,
please read these instructions completely.
Studio Card
AW-PB305AN
This product consists of an studio card and an
interface bracket.
F0806Y1116 DVQTB0134

- 2 -
indicates safety information.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(service) instructions in the literature accompanying the appliance.
The lightning flash with arrowhead symbol, within an equilateral triangle,
is intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
FCC Note:
This equipment has been tested and found to comply with the limits for a class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy, and if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Warning:
To assure continued FCC emission limit compliance, the user must use
only shielded interface cables when connecting to external units. Also, any
unauthorized changes or modifications to this equipment could void the user’s
authority to operate it.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class A est conforme à la norme
NMB-003 du Canada.
For CANADA
Safety precautions

- 3 -
indicates safety information.
WARNING:
• TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE.
• TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, KEEP THIS
EQUIPMENT AWAY FROM ALL LIQUIDS. USE AND STORE ONLY IN
LOCATIONS WHICH ARE NOT EXPOSED TO THE RISK OF DRIPPING OR
SPLASHING LIQUIDS, AND DO NOT PLACE ANY LIQUID CONTAINERS ON
TOP OF THE EQUIPMENT.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING
INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER CHANGES OF
SWITCH SETTINGS INSIDE THE UNIT TO QUALIFIED SERVICE PERSONNEL.
Safety precautions

- 4 -
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near
water.
6) Clean only with dry cloth.
7) Do not block any ventilation
openings. Install in accordance with
the manufacturer’s instructions.
8) Do not install near any heat
sources such as radiators, heat
registers, stoves, or other
apparatus (including amplifiers)
that produce heat.
9) Do not defeat the safety purpose
of the polarized or grounding-
type plug. A polarized plug has
two blades with one wider than the
other. A grounding-type plug has
two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety.
If the provided plug does not fit
into your outlet, consult an
electrician for replacement of the
obsolete outlet.
10) Protect the power cord form being
walked on or pinched particularly
at plugs, convenience receptacles,
and the point where they exit from
the apparatus.
11) Only use attachments/accessories
specified by the manufacturer.
12) Use only with the cart,
stand, tripod, bracket,
or table specified by
the manufacturer, or
sold
with the apparatus. When a cart is
used, use caution when moving
the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during
lightning storms or when unused
for long periods of time.
14) Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such
as power-supply cord or plug is
damaged, liquid has been spilled
or objects have fallen into the
apparatus, the apparatus has been
exposed to rain or moisture, does
not operate normally, or has been
dropped.
Read these operating instructions carefully before using the unit. Follow the safety
instructions on the unit and the applicable safety instructions listed below. Keep
these operating instructions handy for future reference.
IMPORTANT SAFETY
INSTRUCTIONS
indicates safety information.
Safety precautions

- 5 -
Contents
Configuration ........................................ 5
Accessories .......................................... 5
Introduction ........................................... 6
Characteristics ...................................... 6
Precautions for use .............................. 6
Major operating controls and
their functions ................................. 7
Studio card ....................................... 7
Interface bracket .............................. 8
Installing the studio card ..................... 9
Interface bracket mountings ............. 10
Mounting the bracket on a tripod ... 10
Mounting the camera ..................... 10
Mounting the viewfinder
on a bracket................................ 10
Connections ........................................ 11
When configuring a system
with the remote control unit ....... 11
 When configuring a system
with the remote operation panel .... 12
Setting and changing of menu items ... 13
Performing the settings .................. 13
Optional card settings submenu .... 15
Appearance ......................................... 16
Studio card ..................................... 16
Interface bracket ............................ 17
Specifications ..................................... 18
Accessories
Adjuster plug (M6 M3) ......................... 1
Screws (6 mm) ....................................... 2
Screws (8 mm) ....................................... 4
Configuration
Studio card (AW-PB305A U01) ............. 1
Interface bracket (AW-PB305A U02) .... 1

- 6 -
Characteristics
An inter-communications headset can be
used and its volume adjusted.
 The STANDBY/ON switch function of
the viewfinder (WV-VF65B, AW-VF80) is
incorporated.
Output signals (brightness and
composite video signals) to the
viewfinder can be switched using the
menu settings.
Zebra pattern and safety zone displays
appearing in the viewfinder can be
switched using the menu settings.
 The VIDEO ON/OFF switch function of
the viewfinder (AW-VF64) is incorporated.
(In order to prevent CRT burn-in, the
AW-VF64 does not come with a standby
function.)
Introduction
Installing the studio card in a convertible
camera (such as the AW-E350, AW-E650,
AW-E655, AW-E750 and AW-E860) and
mounting the camera on the interface
bracket makes it possible for a viewfinder
and/or inter-communications headset to
be used and thus enable the camera to be
used as a studio camera.
Notes
The AW-PB305A cannot be installed
to the following models;
AW-RP605, AW-PB605
When the studio card unit is to be
discarded at the end of its service
life, ask a specialized contractor
to dispose of it properly in order to
protect the environment.
When connecting or disconnecting a
cable from any unit, ensure that the
power to that unit is turned off.
Do not drop this product or subject it to
strong shock or vibration, as this may
cause it to malfunction.
Avoid using the unit in very humid or
dusty locations, as this may cause it to
malfunction.
Avoid using the product at a cold place
below 14°F (–10°C) or at a hot place
above 113°F (+45°C) because extremely
low or high temperature will adversely
affect the parts inside.
Precautions for use

- 7 -
Major operating controls and their functions
Studio card
EVF connector [EVF]
The EVF cable 7from the interface
bracket is connected here.
2EVF standby / VIDEO ON/OFF
switch
[ST.BY / VIDEO ON/OFF]
<For the WV-VF65B, AW-VF80>
ST.BY : Places the viewfinder in standby
mode.
ON : Outputs images to the viewfinder.
<For the AW-VF64>
VIDEO ON : Outputs images to the
viewfinder.
VIDEO OFF : No images appear on the
viewfinder.
The AW-VF64 does not come with a
standby function.
3 Inter-communications level control
[LEVEL]
This adjusts the sound level output to
the inter-communications headset.
4Inter-communications jack (M3)
[INCOM]
The inter-communications headset is
connected here.
If the plug diameter does not match, use
the adjuster plug (M6 M3) supplied
with this product.
MIC: Dynamic (With Preamp)
50 /–20 dB
Receiver: 150 (max. 200 mW)

- 8 -
Major operating controls and their functions
Interface bracket
5EVF connector 1 [EVF1]
The viewfinder (WV-VF65B, AW-VF80)
is connected here.
6EVF connector 2 [EVF2]
The viewfinder AW-VF64 is connected
here.
7EVF cable
This is connected to the EVF connector 
on the studio card.
8TALLY input connector [TALLY IN]
This is the tally control external input
connector.
OPEN : TALLY OFF
SHORT : TALLY ON
When using the AW-CB400 remote
operation panel and AW-CA50T8G
control cable for connecting to the
convertible camera, connect the TALLY
cable of the AW-CA50T8G to this
connector.
Note
Do not connect EVFs to EVF
connectors 1 and 2 (5and 6) at
the same time.

- 9 -
Installing the studio card
Always ask your local dealer to install the studio card.
Rear panel
Optional card
slot cover
4 screws 5/16” (8 mm)
2 screws 1/4” (6 mm)
Studio card
1
Turn the power to the camera off
and remove any cables which are
connected to the power connector or
other connectors.
2
Loosen the 4 screws [5/16” (8 mm)]
on the rear panel of the camera, then
remove the panel itself.
3
Loosen the 2 screws [1/4” (6 mm)]
on the optional card slot cover, then
remove the cover.
4Align the studio card with the guides
and insert it.
Ensure the card is fully inserted.
5
Firmly tighten the 2 screws [1/4” (6 mm)]
to the optional card slot.
6Firmly secure the rear panel with the
4 screws [5/16” (8 mm)].
Before installing the studio card:
Release the static carried in the body of the person to perform the installation.
Installation can be performed more safely if an anti-static wrist strap is worn.
Touching the card without first releasing this static may cause malfunctioning.
Do not allow the metal part of the card come in contact with any other metal parts.
Note
If the screws are misplaced, use
the extra screws supplied with this
product.

- 10 -
 M ounting the bracket
on a tripod
1
Mount the interface bracket on the
tripod. (Screw: 1/4 – 20 UNC)
Mounting the camera
2
Mount the camera (in which the
studio card has been installed) on the
interface bracket.
Fasten the fixing knob to firmly secure
the camera.
Mounting the viewfinder
on a bracket
3
Mount the mounting base that is
supplied to the viewfinder onto the top
of the interface bracket using the 2
screws provided.
(Mount the base securely so that it is
not unsteady.)
4Slide the viewfinder onto the mounting
base and tighten the fixing knob to
secure it firmly.
5
Connect the viewfinder cable to the
EVF connector 1 or 2 on the interface
bracket.
6Connect the EVF cable from the
interface bracket to the EVF connector
on the studio card.
Interface bracket mountings
Fixing knob
Fixing knob
<WV-VF65B,
AW-VF80, etc.>
Fixing knob
<AW-VF64>
Mounting base
2 screws

- 11 -
Connections
Convertible camera:
AW-E350, AW-E650, AW-E655,
AW-E750, AW-E860, etc.
Viewfinder:
WV-VF65B, AW-VF80, AW-VF64, etc.
Remote control unit (RCU):
WV-RC700A, WV-RC550, AW-RC600,
etc.
Inter-communications headset
Video monitor
Use the RCU cable (AW-CA50A26) to
connect the remote control unit to the
convertible camera.
Power to the camera is supplied from the
remote control unit.
Viewfinder:
WV-VF65B, AW-VF80,
AW-VF64, etc.
Inter-communications headset
Convertible camera:
AW-E350, AW-E650, AW-E655,
AW-E750, AW-E860, etc.
Video monitor
Remote control unit (RCU):
WV-RC700A, WV-RC550,
AW-RC600, etc.
Composite signals
Coaxial cable
RCU cable:
AW-CA50A26
Inter-communications headset
When configuring a system with the remote control unit

- 12 -
Connections
Convertible camera:
AW-E350, AW-E650, AW-E655,
AW-E750, AW-E860, etc.
Viewfinder:
WV-VF65B, AW-VF80, AW-VF64, etc.
Remote operation panel:
AW-CB400, etc.
Video monitor
Use the control cable (AW-CA50T8G) to
connect the remote operation panel to
the convertible camera.
Use the AW-PS505A AC adapter, which
is an optional accessory, for the power
supply.
Inter-communication between the
remote operation panel and studio card
is not possible.
Viewfinder:
WV-VF65B, AW-VF80,
AW-VF64, etc.
Convertible camera:
AW-E350, AW-E650,
AW-E655, AW-E750,
AW-E860, etc.
Video monitor
Remote operation
panel:
AW-CB400, etc.
Control cable:
AW-CA50T8G
TALLY cable
AC adapter:
AW-PS505A
AC adapter:
AW-PS505A
Cable provided with AC adapter
10BASE-T
straight cable
Cable provided
with AC adapter
When configuring a system with the remote operation panel

- 13 -
Performing the settings
1
Display the main menu.
When performing the settings with
the convertible camera:
Press the MENU switch continuously
for at least 5 seconds.
When performing the settings with
the remote control unit (AW-RC600):
Set the MENU switch to “ON”.
Main menu for halogen light mode,
fluorescent light mode and outdoor mode
Main menu for user mode
Convertible camera
Remote control unit (AW-RC600)
Setting and changing of menu items
* “Option Card 2” is displayed on the
menu when the optional card has been
plugged into the optional card slot of
the additional card box.
The mode selected is displayed here.
To return to filming mode
(This is displayed when the convertible
camera is used to perform the settings.)
MENU switch
ITEM/AWC switch
YES/ABC switch
NO/BAR switch
MENU switch
DATA YES/UP switch
ITEM UP switch
ITEM DOWN switch
DATA NO/DOWN switch
Camera settings to match the system configuration and filming conditions can be made
using the menu screens.
See the convertible camera operating instructions for more information on the settings.
For details on the setting procedures when the remote control unit and remote operation
panel are used, refer to the operating instructions of the unit and panel.

- 14 -
2
Select “Option Card 1” to display the
submenu.
When performing the settings with
the convertible camera:
Press the MENU or ITEM/AWC
switch to move the flashing to the
setting item, then press the YES/ABC
switch to display the submenu.
When performing the settings with
the remote control unit (AW-RC600):
Press the ITME UP or ITEM DOWN
switch to move the flashing to the
setting item, then press the DATA
YES/UP switch to display the
submenu.
3
Select the setting item and change the
setting.
When performing the settings with
the convertible camera:
Press the MENU or ITEM/AWC
switch to move the flashing to the
desired setting item, then press
the YES/ABC or NO/BAR switch to
change the setting.
When performing the settings with
the remote control unit (AW-RC600):
Press the ITME UP or ITEM DOWN
switch to move the flashing to the
desired setting item, then press the
DATA YES/UP or DATA NO/DOWN
switch to change the setting.
4
Return to filming mode.
When performing the settings with
the convertible camera:
Press the MENU or ITEM/AWC
switch and select “End” on the main
menu, then press the YES/ABC
switch.
When performing the settings with
the remote control unit (AW-RC600):
Set the MENU switch to “OFF”.
After being returned to filming mode,
the convertible camera will operate as
per the changed settings.
Setting and changing of menu items

- 15 -
Setting and changing of menu items
Zebra indicator (ON, OFF)
This sets the zebra pattern display
which appears in the viewfinder.
ON : Zebra patterns are displayed in
the viewfinder.
OFF : Zebra patterns are not displayed
in the viewfinder.
<Note>
Even if “ON” is selected for this setting,
the zebra patterns will not be displayed
in the viewfinder if “CVBS” has been
selected as the EVF output 4setting.
2Level (70% to 110%)
The zebra patterns are displayed to use
as a yardstick for the brightness level.
<Note>
These settings are available when
“ON” has been selected for the Zebra
indicator setting.
3Safety zone (1 to 4, OFF)
This selects the type of safety zone that
is displayed in the viewfinder.
If “OFF” is selected, a safety zone will
not be displayed.
<Note>
The safety zone and the center marker
reflect the electrical positions which may
differ from the optical positions.
The inner frame and the outer frame
are approximately 90% and 95%,
respectively, of the safety zone.
4EVF output (Y, CVBS)
This sets the signals to be output to the
viewfinder.
Y : Brightness signals are output to
the viewfinder.
CVBS :Color signals are output to the
viewfinder.
<Note>
The zebra pattern is not displayed in
the viewfinder when “CVBS” has been
selected.

2
3
4
Optional card settings submenu

- 16 -
Appearance
3-9/16 (91)7/8
(21.5)
2-3/4 (70)
Unit: inch (mm)
Studio card
3-3/4 (96)

- 17 -
7-3/16 (183)
7-1/2 (190)
Appearance
Unit: inch (mm)
Interface bracket
5-9/16 (141) 1-3/16 (30)
2-1/16 (50)

- 18 -
Specifications
Ambient operating temperature: +14°F to +113°F (–10°C to +45°C)
Ambient operating humidity: 30% to 90% (without condensation)
Dimensions (WHD):
Studio card 7/8”2-3/4”3-9/16” (21.57091 mm)
(excluding protrusions)
Interface bracket 7-1/2”7-3/16”6-3/4” (190183171 mm)
(excluding protrusions)
Weight:
Studio card 0.2 lbs. (0.08 kg)
Interface bracket 2.1 lbs. (0.94 kg)
Input/output connector:
Studio card
EVF connector 6-pin, square
Inter-communications jack M3
Interface bracket
EVF connector 1
10-pin, round, composite signals/brightness, 1.0 V [P-P]
EVF connector 2 6-pin, round, composite signals/brightness, 1.0 V [P-P]
TALLY input connector BNC
Switch/control functions:
Studio card EVF standby / VIDEO ON/OFF switch
WV-VF65B, AW-VF80 ST.BY/ON
AW-VF64 VIDEO ON/VIDEO OFF
Inter-communications level control
Menu screens Zebra indicator (ON/OFF)
Level (70% to 110%)
Safety zone (1/2/3/4/5/OFF)
EVF output (Y/CVBS)
Weight and dimensions shown are approximate.
Specifications are subject to change without notice.
Source voltage: 12 V DC (supplied from convertible camera)
Power consumption: 15 W (When WV-VF65B, AW-VF80 is connected)
indicates safety information.

- 19 -
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Memo

PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY
UNIT COMPANY OF PANASONIC CORPORATION OF NORTH AMERICA
Executive Office:
One Panasonic Way 4E-7, Secaucus, NJ 07094 [phone]
EASTERN ZONE:
One Panasonic Way 4E-7, Secaucus, NJ 07094 [phone]
Southeast Region:
1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 [phone]
Central Region:
1707 N Randall Road E1-C-1, Elgin, IL 60123 [phone]
WESTERN ZONE:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 [phone]
Government Marketing Department:
52 West Gude Drive, Rockville, MD 20850 [phone]
Broadcast PARTS INFORMATION & ORDERING:
9:00 a.m. – 5:00 p.m. (PST) [phone]/24 Hr. Fax [phone]
Emergency after hour parts orders [phone]
TECHNICAL SUPPORT:
Emergency 24 Hour Service [phone]
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 [phone]
Panasonic de Mexico S.A. de C.V.
Av angel Urraza Num. 1209 Col. de Valle 03100 Mexico, D.F. (52) 1 951 2127
Panasonic Puerto Rico Inc.
San Gabriel Industrial Park, 65th Infantry Ave., Km. 9.5, Carolina, Puerto Rico 00630
[phone]
© 2006 Matsushita Electric Industrial Co., Ltd. All rights reserved.