AMQ Solutions ACTIV-1 User manual

installation guide
ACTIV-1
sit-to-stand desks

Phase 1 ACTIV-1 Installation Guide
P2 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Components
1. Components layout
foot x 2
cantilever x 2leg x 2
handset x 1motor x 1
aluminum connecting rod x 1
steel drive rod x 2 (long & short)
power box x 1
stretcher bar unit
center
left right
allen keys screws
(comes mounted in
connecting rod)
M5 X 4 M5 X 6 M5 X 12
Hardware

ACTIV-1 Installation Guide
P3 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Phase 2 Stretcher Bar Unit Assembly
2. Stretcher bar unit assembly
Assemble center stretcher bar in the middle.
Adjust stretcher bar to desired length and tighten with six M5 screws
71” 65” 59” 53” 53” 59” 71”65”49”
*THE FRAME WIDTH CAN BE PRESET TO 71, 65, 59, 53, AND 47”.
1
2
Assemble center, left and right stretcher bar
Preset stretcher bar to desired length
and tighten with six M5 screws.

ACTIV-1 Installation Guide
P4 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Motor AssemblyPhase 3
1Mount motor unit on stretcher bar
using three M5 screws.
3. Motor assembly
Mount the motor unit on stretcher bar using twelve M5 screws

ACTIV-1 Installation Guide
P5 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
4. Leg column assembly
Attach both leg columns to the stretcher bar ends using twelve M5 screws
Make sure that the rod opening side
of the leg columns are facing toward
each other. This side will not have
a button pattern or bolt holes.
Leg Column AssemblyPhase 4
1Attach both leg columns to the stretcher bar ends using M5 screws.

ACTIV-1 Installation Guide
P6 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Feet AssemblyPhase 5
1Attach both feet using M5 screws.
5. Feet assembly
Attach both feet using twelve M5 screws

ACTIV-1 Installation Guide
P7 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Phase 6 Drive Rods Assembly
21
Tighten M5 x4 screws
after install the drive rod
5. Drive rods assembly
Insert short drive rod through the motor unit and into the right leg column
1
1
2
2
Insert short drive rod through the motor unit and into
the right leg column.
Extend the long drive into the left leg column.

ACTIV-1 Installation Guide
P8 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Cantilever AssemblyPhase 7
7. Cantilever assembly
Attach cantilever to the leg columns
Use M5 screws to fasten in place
1Attach cantilever to the leg columns.
Use M5 screws to fasten in place.

ACTIV-1 Installation Guide
P9 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Connecting Control and PowerPhase 8
8. Connecting control and power
Connect power plug after the handset are connected properly
Facing
Direction
Handset
Motor
Power box
Connect each plugs according to the drawing.
Orientate yourself the the table assembly by facing as
a user to identify left and right motor.
1Orient yourself to the table
assembly by facing as a user
to identify left and right motor.
After the hand set and control
box are connected properly,
connect power plug.

ACTIV-1 Installation Guide
P10 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.
Program Height Memory PresetsPhase 9
1
1
2
2
To Program Up to 3 Presets: Use the up/
down arrows to find desired height, then
press “M” followed by the number 1, 2, or 3.
To Test Programmed Height: Use the up/
down arrows to adjust the table to a height
other than the preset height. Then push and
hold the number you programmed to see
if it automatically adjusts to the height
programmed in Step 1.
Note: If it does not adjust to the
programmed height, repeat Step 1
followed by Step 2.
Caution: Once the preset number is
pushed, the base will automatically
moved to the programmed height.
123
M

915 Walsh Avenue / Santa Clara, CA 95050 [phone] amqsolutions.com
5 Day Open Plan we provide exceptional
experiences with reliable, easy interactions
and successfully fulfilled orders in only 5 days