Amulex ESB030 User manual

External Socket Box
User’s Manual
For 6KVA
1
Table of Contents
1.
Important Safety Instruction .................................................................................. 2
2. Installation and Operation...................................................................................... 3
2.1. ESB Unpacking............................................................................................ 3
2.2. Selecting Installation Position...................................................................... 3
2.3. Wire Assembly of the Input & Output......................................................... 3
2.4. Installation and Operation............................................................................ 4
3. Trouble Shooting ................................................................................................... 5
4. Specifications......................................................................................................... 6
5. Installation Illustration ........................................................................................... 7
5.1. 220/230/240VAC WITHOUT GTM ........................................................... 7
5.2. 110VAC/220VAC (115/230 or 120/240VAC) WITH GTM....................... 7
5.3. 220/230/240VAC WITHOUT GTM ......................................................... 10
5.4. 220/230/240VAC WITH GTM.................................................................. 10
5.5. Terminal Block Explanation ...................................................................... 12

2
1. Important Safety Instruction
•Do not open the case, as there are no serviceable parts inside. Your warranty will be
void.
•Do not try to repair the unit yourself, contact your local supplier or your warranty will
be void.
•SAVE THESE INSTRUCTIONS--This manual contains important instruction that
should be followed while installation and operation.
•Make sure that the AC Utility outlet is correctly grounded to avoid any possibility of
unpredictable voltage leakage.
•Make sure the input voltage is within the windows stated in the specs sheet and the
load connected is within the rated capacity.
•Should a strange noise, or smell occur, please turn off the unit and consult your local
distributor for repair immediately.
3
2. Installation and Operation
2.1. ESB Unpacking
2.1.1. Remove the PE foam of the ESB.
2.1.2. Check attached accessories.
¾User’s Manual x 1 copy
¾Screws x 1 set
¾Fixing metal kit x 2 sets
2.2. Selecting Installation Position
It is necessary to select a proper environment to install the unit, in order to minimize
the possibility of damage to the ESB and extend its life. Please follow the instructions
below:
z Please ensure the installation site environmental conditions are in accordance
with working specifications to avoid overheat and excessive moisture.
z Do not place the ESB in a dusty or corrosive environment or near any flammable
objects.
z This ESB is not designed for outdoor use.
2.3. WireAssembly of the Input & Output
To UPS
OUTPUT
BREAKER
PUSH TO RESET
OUTPUT
BREAKER
PUSH TO RESET
Figure 1: ESB front Panel
○
1
Input Power Cord(To UPS): to the Power Module or the output terminal of the
transformer Module GTM.
○
2
&Output Circuit Breaker: for protection purpose
○
3
&Output Socket: to the Load

4
2.4. Installation and Operation
The ESB is specially designed for On Line 6KVA convertible UPS. Its installation
procedures might be dependent on the Power Module or the Transformer Module GTM
chosen. You may refer to Figure 2 and Chapter 5 for a proper installation.
Installation Procedure:
1. Unpack the package and keep the package for future use.
2. Check if any damage occurred during transportation. If yes, please contact with your
local agent.
3. Make sure the Input Power cord & Output sockets of the ESB are in accordance with
the PM or GTM chosen.
4. Shut down the load connected to the UPS and remove the input cable of the load
from the UPS, then turn off the UPS and remove the input power cord of the UPS
from the wall receptacle.
5. Fasten the fixing kit onto the ESB as Figure 2.
6. Fasten the fixing kit #1 to the Battery Module or the fixing kit #2 to the Rack Cabinet
as figure 2.
7. Connect the input Power Cord of the ESB to the output Terminal of the PM or GTM.
8. Connect the output load evenly to the output sockets of the ESB. Make sure
There is no overload condition occurs and all the loads connected are complied with
the specs of the UPS.
9. Start up the UPS according to the user’s manual of the UPS.
To UPS
OUTPUT
BREAKER
PUSH TO RESET
OUTPUT
BREAKER
PUSH TO RESE T
To UPS
OUTPUT
BREAKER
PUSH TO RESET
OUTPUT
BREAKER
PUSH TO RESE T
Fixing metal
Type 2
Fixing metal
Type 1
Figure 2: ESB Fixing Kits and their Installation
5
3. Trouble Shooting
Should not your ESB operate normally, you may make some proper adjustments and
replacements as indicated below. Should the ESB still operate abnormally, please consult
with your local agent immediately.
Situation Checked Items Solution
UPS has no output.
Please refer to the operation manual
of the UPS for start up the UPS
properly.
Some or all of
the loads are not
supplied with
electrical energy
The Circuit Breaker the
Output sockets of the ESB is
tripped.
Reset the Circuit Breaker.
There is no
electrical energy
supply after reset
the output circuit
breaker, even
though the UPS
output is normal.
Over-current at the Output
Socket Reduce some uncritical load

6
4. Specifications
Operational Temperature 32℉to 104℉(0℃to ＋40℃)
Storage Temperature -4℉to 140℉(－20℃to ＋40℃)
Dimension: W×D×H(mm) 86x50x326 / 86×65×326*
Net Weight(kg) 3.2
Model
Number Rating Output Receptacles/Protection
ESB030
100~240VAC, 6000VA(MAX)
NEMA6-20R x 1 with 20A Circuit Breaker
NEMA6-30R x 1
NEMA5-15R x 4 with 15A Circuit Breaker
ESB030A
100~240V, 6000VA(MAX)
NEMA6-30R x 1 with 30A Circuit Breaker
NEMA5-30R x 1 with 30A Circuit Breaker
NEMA5-20R x 1 with 20A Circuit Breaker
NEMA5-15/20R x2 with 20A Circuit Breaker
ESB115
100~120VAC, 6000VA(MAX) NEMA5-15R x 8 with 15A Circuit Breaker
ESB230
200~240VAC, 6000VA(MAX) NEMA6-20R x 2 with 20A Circuit Breaker
NEMA6-30R x 1
ESB230A
200~240VAC, 6000VA(MAX)
NEMA6-30R x 1 with 30A Circuit Breaker
NEMA6-20R x 1 with 20A Circuit Breaker
NEMA6-15/20R x4 with 20A Circuit Breaker
ESB216
200~240VAC, 6000VA(MAX) IEC C19(16A) x 2 with 16A Circuit Breaker
IEC C13(10A) x 8 with 10A Circuit Breaker
ESB216G
200~240VAC, 6000VA(MAX) Local Socket x 2 with Circuit Breaker **
IEC C13(10A) x 4 with 10A Circuit Breaker
* ESB030A and ESB230A
** Local Socket: Schuko(German) with 16A Circuit Breaker, British with 13A Circuit Breaker, Australian with
10A Circuit Breaker or French with 16A Circuit Breaker。
7
5. Installation Illustration
5.1. 220/230/240VAC WITHOUT GTM
Figure 3: PM + BM 7AH + ESB230
5.2. 110VAC/220VAC (115/230 or 120/240VAC) WITH GTM
Figure 4: PM + GTM-WS + BM 7AH + ESB030
Figure 5: PM + GTM-WOS + BM 7AH +ESB030

8
Figure6: PM + GTM-WS + BM 7AH + ESB030A
Figure 7: PM + GTM-WS + BM 7AH + ESB230
Figure 8: PM + GTM-WOS + BM 7AH + ESB230
9
Figure 9: PM + GTM-WS + BM 7AH + ESB115
Figure 10: PM + GTM-WOS + BM 7AH + ESB115
Figure 11: PM + GTM-WS + BM 7AH + ESB230A

10
5.3. 220/230/240VAC WITHOUT GTM
Figure 12: PM + BM 7AH + ESB216
5.4. 220/230/240VAC WITH GTM
Figure 13: PM + GTM-WS + BM 7AH + ESB216
Figure 14: PM + GTM-WOS + BM 7AH + ESB216
11
Figure 15: PM + GTM-WS + BM 7AH + ESB216G
Figure 16: PM + GTM-WOS + BM 7AH + ESB216G

12
5.5. Terminal Block Explanation
Model
Number Terminal Block Explanation
ESB030
ESB030A
ESB115
ESB230
ESB230A
ESB216
ESB216G
13

14 15
192321152002002