Installation Guide
CB-MXP43 Rough-In Box and Cover Plate for Modero X Series®4.3” Panel
Overview
The CB-MXP43 Rough-In Box (FG039-19) is an optional accessory for the Modero X
Series®4.3” Wall Mount Touch Panel. It allows the panel to be mounted directly to the
studs/pre-wall.
The back of the Modero X Series 4.3” Wall Mount Touch Panel is contained within a
plastic outer housing or back box, and the back box attaches to the Rough-In Box. The
Rough-In Box kit includes a wall box and cover and mounting screws.
Specifications
WARNING: In order to guarantee a stable installation of the touch panel, the distance
between the CB-MXP43 and the outer wall surface must be a minimum of .50 inches
(1.27cm) and a maximum of .1.50 inches (3.81cm).
• Refer to the 95-5968-38 diagram for detailed installation dimensions.
Pre-Wall Installation of the CB-MXP43 Rough-In Box
1. Remove the rough-in box cover (Bin FIG. 1) before installation of the Rough-In
Box (A). Note: the cover MUST be removed before drywall installation. The
cover may be reinstalled after drywall installation using 4-40 screws (not
included).
2. Fasten the CB-MXP43 rough-in box to the stud through the holes on the Stud
Mounting tabs, using either nails or screws (not provided).
3. Remove the appropriate wiring knockouts from the rough-in box to
accommodate the cables being threaded through to the 7” Wall Mount Touch
Panel.
4. Thread the incoming Ethernet and USB wiring through the bottom knockout.
Leave enough slack in the wiring to accommodate installation of the touch panel.
5. Install the drywall/sheetrock before inserting the back box for the CB-MXP43.
6. Cut out the opening for the Wall Mount Touch Panel back box where the wall has
been placed over the Rough-In Box. Cutting out the surface slightly smaller than
what is outlined in the installation drawings, so thatyou can make any necessary
cutout adjustments, is very highly recommended.
NOTE: The front cover of the CB-MXP43 (B in FIG. 1) should be installed after the
appropriate wiring is pulled to the Rough-In Box. The cover should then be removed
prior to the installation of the touch panel back box and discarded.
7. NOTE: The touch panel’s back box does not mount to the CB-MXP43. The back
box still has to attach to the wall with 4 screws in each corner of the box. (See
diagram below.)
FIG. 1 CB-MXP43 Rough-In Box - with front cover
5.58”
(14.16 cm)
A
2.84”
(17.30 cm)
4.32”
(7.22 cm)
B
Rough-In Box With Cover
Cover
Rough-In Box
CB-MXP43 (FG039-19) Specifications
Dimensions (HWD) • Rough-In Box: 5.58" x 2.84" x 2.21"
(14.16 cm x 7.22 cm x 5.60 cm)
• Rough-In Box Cover Plate: 4.32” x 2.84” x 0.06”
(10.96 cm x 7.22 cm x 1.52 mm)
Weight • With cover: 0.90 lbs (0.75 kg)
• Without cover: 0.70 lbs. (0.32 kg)
Certifications • cTUVus Listed
• UL Listed
Included
Accessories: • Cover Plate for Rough-in Box (62-5968-39)
• Cover Plate to Rough-In Box Mounting Screws (2)
(80-0139-06)
Recommended
Wall Cutout
for the CB-MXP43
3 1/2”
(8.89 cm)
2 3/4”
(6.98 cm)
NOTE: The CB-MXP43
has beveled corners, so
be careful when cutting
the corners for the entry
hole.
The MXD-430 back box
does not install directly
into the CB-MXP43.
The back box must be
installed with screws
at these points.
