For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
1/10
©2010 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-2261-50 REV: B
To connect the Touch Panel to the internal connectors in the Table-Top Stand:
1. ETHERNET/POE Port on the NXD-500i: Connect the RJ45 connector inside
the Table-Top Stand to the ETHERNET/POE port on the side panel of the
NXD-500i.
2. USB Port on the NXD-500i: Connect the USB connector inside the Table-Top
Stand to the USB port on the side panel of the NXD-500i.
Mounting the Microphone in the Table-Top Stand
The microphone cable connects to the NXD-500i at the bottom right corner of the front
panel (FIG. 6):
1. Insert the microphone into the microphone notch on the upper-right corner of the
Table-Top Stand (FIG. 7):
2. Plug the microphone cable into the microphone cable connector at the lower-
right corner of the NXD-500i (see FIG. 6).
Step 5: Install The NXD-500i Into the Table-Top Stand
At this point the touch panel can be installed in the TTS enclosure:
1. Slide the touch panel into the Table-Top Stand until the front edge of the panel
sits flush against the front panel of the Table-Top Stand.
Note: Be careful not to pinch or damage the cables connecting the NXD-500i to
the internal connectors in the Table-Top Stand. In particular, be sure to position
the microphone cable such that it is not damaged or pinched when the panel is
inserted into the Table-Top Stand.
2. Use the two mounting screws (included with the Table-Top Stand) to secure the
touch panel to the Table-Top Stand enclosure (FIG. 8).
Note: Do not use excessive force or over-tighten the screws - doing so could damage
the touch panel.
Step 6: Re-Install the Bezel on the NXD-500i
The Bezel snaps on and off the NXD-500i, no screws are used or required.
To re-install the Bezel on the NXD-500i:
1. Carefully align the Bezel with the front of the NXD-500i panel. Note the
positions of the notches on the front of the panel and the tabs on the inside of
the Bezel.
Note: Make sure to align the Microphone, Light, and PIR Motion sensor
locations to their respective openings on the Bezel.
2. Gently press the top edge of the Bezel into the top edge of the panel, and
engage the metal tabs on the panel with the matching notches on the Bezel.
3. Gently press the bottom edge of the Bezel on to the bottom edge of the panel
until it snaps into place.
Step 7: Install the Bezel on the NXA-TTS500-BL
The final step is to install the Bezel on the Table-Top Stand: the Bezel slides onto the
Table-Top Stand from the rear.
Note: Orient the bezel so that the microphone notch is located at the upper-right
corner (when viewed from the front)
Slide the Bezel on to the NXA-TTS500-BL, from the rear of the enclosure, until it is
flush against the mounting tabs on the Table-Top Stand.
FIG. 9 provides an exploded view of the entire assembly including the NXD-500i
Bezel, Panel, Table-Top Stand and NXA-TTS500 Bezel:
NXA-TTS500-BL Rear Panel Connectors
Use the Ethernet and USB connectors on the rear panel of the NXA-TTS500-BL to
connect the touch panel to the control system. Once connected, these connectors
behave exactly the same as the ETHERNET/POE and USB ports on the touch panel
itself.
Secure Mounting / Alternate Cable Routing
The NXA-TTS500-BL features a cable routing knockout on the bottom panel,
mounting holes and internal strain relief to provide a secure table-top installation
option (FIG. 10).
Refer to the TTS Secure Mounting / Alternate Cable Routing Installation Guide
(available at www.amx.com) for instructions.
Additional Documentation
Refer to the NXD-500i Operation/Reference Guide (available at ww.amx.com) for
details on wiring and connection information for the NXD-500I.
FIG. 6 NXA-TTS500-BL - Microphone connector
FIG. 7 NXA-TTS500-BL - Microphone notch
FIG. 8 Inserting the NXD-500i into the NXA-TTS500-BL - secure with 2 mounting screws
microphone
connector
microphone installed
NXD-500i panel (front)
on the NXD-500i.
See Fig 7 for mounting
location on the NXA-TTS500-BL
microphone
mounts into
this notch
NXA-TTS500-BL rear panel
NXD-500i
Panel
NXA-TTS500-BL
mounting screws
FIG. 9 Installing the Bezel on the Panel/Table-Top Stand assembly
FIG. 10 Bottom Panel (Alternate Cable Routing)
NXA-TTS500
NXD-500i
Table-Top Stand
microphone
notch
Bezel
Bezel
NXD-500i
Panel
(rear)
Surface Mounting holes are
beneath the rubber feet
Surface Mounting holes
Cable knockout
The Strain Relief Bracket
(mounted inside the enclosure)
also uses this mounting hole
