AMX X Series User manual

Quick Start Guide
MXA-FMK-07 Modero X Series®Flush Mount Kit
MXA-FMK-07
The MXA-FMK-07 Flush Mount Kit (FG5968-71) allows the Modero X Series 7”
Wall Mount Touch Panels to be installed nearly flush with the wall. Once
installed, simply press lightly on the black border area on both sides of the touch
panel, and the spring-loaded mechanism switches the panel between the flush
position or slightly extended from the wall surface. The extended position gives
access to the panel’s Sleep/Setup button, as well as for enhanced speaker and
microphone exposure. The MXA-FMK-07 is compatible with all Modero X Series
7” Wall Mount Touch Panels, including the MXD-701-P (FG5968-54), MXD-701-
L (FG5968-55), MXD-700-P (FG5968-08), MXD-700-L (FG5968-14), MXD-700-
P-NC (FG5968-28), and the MXD-700-L-NC (FG5968-29)
• Refer to the 95-5968-71 diagram for detailed installation dimensions.
Pre-Wall Installation of the Flush Mount Kit
The MXA-FMK-07 Flush Mount Kit (FIG. 1) is designed to attach the panel to
most standard wall and solid surface materials. This Flush Mount Kit has two
locking tabs (landscape: one on top and one on bottom; portrait: one on each
side) to help lock the Flush Mount Kit to the wall. These locking tabs are only
extended AFTER the Flush Mount Kit is inserted into the wall. Using the locking
tabs is highly recommended for standard mounting surfaces such as walls.
WARNING: When installing the Flush Mount Kit, make sure that the assembly is
in the correct position and in the correct place. Once the locking tabs are
extended and locked into place, removing the Flush Mount Kit may be difficult
without having access to the back of the wall or causing damage to the wall.
Note: In order to guarantee a stable installation of the MXA-FMK-07, the
thickness of the wall material must be a minimum of .50 inches (1.27cm) and a
maximum of .875 inches (2.22cm). The surface should also be smooth and flat.
WARNING: The maximum recommended torque to screw in the locking tabs on
the plastic Flush Mount Kit is 5 IN-LB [56 N-CM]. Applying excessive torque
while tightening the tab screws, such as with powered screwdrivers, can strip
out the locking tabs or damage the plastic.
1. After ensuring proper placement, cut out the mounting surface, using the
MXA-FMK-07 Cutout Template (68-5968-06) as a guide (FIG. 2).
CAUTION: The cutout dimensions shown will allow the unit to pass through
without any dragging or interference. The outer phantom lines show the
perimeter of the mounting flange. If any part of the cutout extends up to or
beyond that perimeter, the cut edge will be visible after installation, or the unit
could fall through the opening. A larger cutout reduces the available surface to
support the unit when mounted, so the cut should be as close to the indicated
dimensions as possible. If the cutout is too small, forcing the unit into place
could result in mechanical binding, faulty operation, or damage to the product.
Always check for a proper fit before final installation.
2. Remove the knockout at the top of the Flush Mount Kit (FIG. 3) and thread
the incoming wiring through the knockout hole. The MXA-FMK-07 has only
one knockout hole, at the top of the device (Landscape) or to the left
(Portrait)..
3. Thread the incoming Ethernet wiring from their terminal locations through
the surface opening and through the knockout.
4. Push the Flush Mount Kit flat into the mounting surface and secure with the
locking tabs (FIG. 4). In order to prevent damage to the touch panel, make
sure that any screws used are flush with the Flush Mount Kit, and the
Flush Mount Kit goes freely into the opening.
5. Insert each connector into its corresponding location along the back of the
touch panel. For more information, please refer to the Quick Start Guide for
the panel being installed.
6. Test the incoming wiring by attaching the panel connections to their termi-
nal locations and applying power. Verify that the panel is receiving power
and functioning properly to prevent repetition of the installation.
Note: Do not disconnect the connectors from the touch panel. The unit must be
installed with the attached connectors before being inserted into the drywall.
7. Latch the panel onto the top hooks on the Flush Mount Kit and rotate it
down (Landscape) onto the bottom snaps or on the left side and rotate it to
the right (Portrait installation). Press gently but firmly and evenly on the
surface of the glass until the bottom panel snaps “click” to lock it down.
FIG. 1 MXA-FMK-07, Landscape and Portrait Installations
Product Specifications
Dimensions (HWD): 5.50” x 8.01” x 3.48” (13.97 cm x 20.33 cm x 8.85 cm)
Weight: 1.00 lbs (0.45 kg)
Included Accessories: • MXA-FMK-07 Quick Start Guide (93-5968-07)
• MXA-FMK-07 Cutout Template (68-5968-06)
Other AMX
Equipment: • MXD-701-P 7" Modero X® Series G5 Wall Mount Touch Panel, Portrait (FG5968-54)
• MXD-701-L 7" Modero X® Series G5 Wall Mount Touch
Panel, Landscape (FG5968-55)
• MXD-700-P 7" Modero X® Series Wall Mount Touch
Panel, Portrait (FG5968-08)
• MXD-700-L 7" Modero X® Series Wall Mount Touch
Panel, Landscape (FG5968-14)
• MXD-700-P-NC 7" Modero X® Series Wall/Flush Mount
Touch Panel (no Microphone), Portrait (FG5968-28)
• MXD-700-L-NC 7" Modero X® Series Wall/Flush Mount
Touch Panel (no Microphone), Landscape (FG5968-29)
Landscape
Portrait
8.01” (20.33 cm)
5.50” (13.97 cm)
FIG. 2 MXA-FMK-07 Cutout Template
FIG. 3 Inserting the MXA-FMK-07 into the wall surface (Landscape)
7.60”
5.09”
(12.94 cm)
(19.30 cm)
Perimeter
of Flush
Mount Kit
flange
Wall Surface
MXA-FMK-07
Knockout
Locking Tab
Note: The
MXA-FMK-07
has only one
knockout hole.

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
1/14
©2014 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax [phone] • technical support 800.932.6993 • www.amx.com
93-5968-71 REV: C
Note: To help lock down the bottom of the touch panel, use a screwdriver or
other flat tool to hold the lower edge of the clear back box casing above the lip of
the main flush mount case while snapping down the bottom. For best results,
use the flat tool on one side, lock down that side, and repeat the process on the
other side.
Using the MXA-FMK-07
Once the touch panel is installed in the MXA-FMK-07, the panel may be
extended from the wall for enhanced speaker and microphone exposure and to
access the panel’s Sleep/Setup button. To extend the panel from the Flush
Mount Kit, press gently on either side of the panel’s surface until you hear or feel
a “click”. Release the panel to extend it.
To return the touch panel to its flush position, press again gently on both side s
of the panel’s surface, on the black border on the edge of the panel,. until you
hear or feel a “click”. When you release the panel’s surface, the panel will remain
in its flush position.
Removing the Touch Panel From the MXA-FMK-07
The touch panel may only be removed from the MXA-FMK-07 when the touch
panel is extended from the wall. For more information on uninstallation of the
touch panel in question, please refer to the Operation Reference Guide of the
panel in question, available at www.amx.com.
A Note About Wall and Rack Installation
Some products are installed in areas of differing temperature and cooling
methodologies. These include products installed in walls, racks, cabinets, etc.
Those areas may have different temperatures and/or cooling approaches that
must be taken into consideration to maintain the product within the specified
operating temperature.
FIG. 5 shows an AMX device installed in a wall with a filled volume (such as with
insulation or concrete), as well as with a closed volume (such as between studs
in an otherwise finished wall). The diagram shows how heat generated by the
device or other devices may have no way to escape, and may build up to levels
that may affect device operation.
In FIG. 6, the diagram displays an AMX device in a typical rack mounting, with
full air circulation around the front and back of the device. In this case, the main
concern is with heat building up between components, possibly to levels that
may affect device operation.
Installation Recommendations
During any installation, a lack of ventilation may produce conditions that may
adversely affect the device’s operation. In these circumstances, special care
must be made to make sure that temperatures within enclosed areas do not
exceed the device’s maximum rated temperature.
FIG. 4 Locking Tab location on the MXA-FMK-07 (Landscape)
Locking Tab Screw
Locking Tab Screw
Use a screwdriver
or other flat tool
to hold the lower
edge of the back
box above the
case while snapping
down the touch panel.
FIG. 5 Heat convection in filled or closed volume, limited or no convection
FIG. 6 Heat convection in rack-mounted devices