Analog Devices ADSP-TS101S EZ-KIT Lite User manual

ADSP-TS101S EZ-KIT Lite®
Evaluation System Manual
Revision 2.1, April 2006
Part Number
82-000635-01
Analog Devices, Inc.
One Technology Way
Norwood, Mass. 02062-9106 a

Copyright Information
©2006 Analog Devices, Inc., ALL RIGHTS RESERVED. This document
may not be reproduced in any form without prior, express written consent
from Analog Devices, Inc.
Printed in the USA.
Limited Warranty
The EZ-KIT Lite evaluation system is warranted against defects in materi-
als and workmanship for a period of one year from the date of purchase
from Analog Devices or from an authorized dealer.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without
prior notice. Information furnished by Analog Devices is believed to be
accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use; nor for any infringement of patents or other rights of
third parties which may result from its use. No license is granted by impli-
cation or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark Notice
The Analog Devices logo, TigerSHARC, VisualDSP++, the VisualDSP++
logo, CROSSCORE, the CROSSCORE logo, and EZ-KIT Lite are regis-
tered trademarks of Analog Devices, Inc.
All other brand and product names are trademarks or service marks of
their respective owners.

Regulatory Compliance
The ADSP-TS101S EZ-KIT Lite evaluation system has been certified to
comply with the essential requirements of the European EMC directive
89/336/EEC (inclusive 93/68/EEC) and, therefore, carries the “CE”
mark.
The ADSP-TS101S EZ-KIT Lite evaluation system had been appended to
Analog Devices Development Tools Technical Construction File refer-
enced “DSPTOOLS1” dated December 21, 1997 and was awarded CE
Certification by an appointed European Competent Body and is on file.
The EZ-KIT Lite evaluation system contains ESD
(electrostatic discharge) sensitive devices. Electro-
static charges readily accumulate on the human
body and equipment and can discharge without
detection. Permanent damage may occur on devices
subjected to high-energy discharges. Proper ESD
precautions are recommended to avoid performance
degradation or loss of functionality. Store unused
EZ-KIT Lite boards in the protective shipping
package.

ADSP-TS101S EZ-KIT Lite Evaluation System Manual v
CONTENTS
PREFACE
Purpose of This Manual ................................................................. xii
Intended Audience ......................................................................... xii
Manual Contents .......................................................................... xiii
What’s New in This Manual .......................................................... xiii
Technical or Customer Support ...................................................... xiv
Supported Processors ...................................................................... xiv
Product Information ....................................................................... xv
MyAnalog.com .......................................................................... xv
Processor Product Information ................................................... xv
Related Documents .................................................................. xvi
Online Technical Documentation ............................................ xvii
Accessing Documentation From VisualDSP++ .................... xviii
Accessing Documentation From Windows .......................... xviii
Accessing Documentation From Web ................................... xix
Printed Manuals ....................................................................... xix
VisualDSP++ Documentation Set ......................................... xix
Hardware Tools Manuals ...................................................... xix
Processor Manuals ................................................................. xx

CONTENTS
vi ADSP-TS101S EZ-KIT Lite Evaluation System Manual
Data Sheets .......................................................................... xx
Notation Conventions ................................................................... xxi
USING ADSP-TS101S EZ-KIT LITE
Package Contents ......................................................................... 1-2
Default Configuration .................................................................. 1-3
Installation and Session Startup ..................................................... 1-5
Evaluation License Restrictions ..................................................... 1-7
Memory Map ............................................................................... 1-7
SDRAM Interface ......................................................................... 1-8
Programmable FLAG Pins ............................................................ 1-9
Interrupt Pins ............................................................................. 1-10
Flash Memory ............................................................................ 1-11
Audio Interface ........................................................................... 1-11
Example Programs ...................................................................... 1-12
Flash Programmer Utility ............................................................ 1-13
Handling ADSP-TS101S EZ-KIT Lite Flash Memory ............ 1-13
ADSP-TS101S EZ-KIT LITE HARDWARE REFERENCE
System Architecture ...................................................................... 2-2
External Port ........................................................................... 2-3
Expansion Interface ................................................................. 2-3
JTAG Emulation Port ............................................................. 2-4
DIP Switch Settings ...................................................................... 2-4
Control Impedance Selection ................................................... 2-5

ADSP-TS101S EZ-KIT Lite Evaluation System Manual vii
CONTENTS
Drive Strength Selection .......................................................... 2-5
Boot Mode Settings ................................................................. 2-6
Interrupt Enable Settings ......................................................... 2-7
Clock Mode Settings ............................................................... 2-7
LEDs and Push Buttons ................................................................ 2-8
USB Monitor LED (LED1) ..................................................... 2-8
Reset LEDs (LED2, LED8–9) ................................................. 2-8
Power LED (LED3) ................................................................. 2-9
FLAG LEDs (LED4–7) ......................................................... 2-10
Reset Push Button (SW1) ...................................................... 2-10
Programmable FLAG Push Buttons (SW2, SW4–5, and SW9) 2-10
Interrupt Push Buttons (SW3 and SW6) ................................ 2-11
Connectors ................................................................................. 2-12
Audio (P2 and P3) ................................................................. 2-12
USB (P4) .............................................................................. 2-13
JTAG (P5) ............................................................................ 2-13
Expansion Interface (P11–13) ................................................ 2-14
Link Ports (P7–10) ................................................................ 2-14
Power Connector (P14) ......................................................... 2-15
Power Supply Specifications ........................................................ 2-15
ADSP-TS101S EZ-KIT LITE BILL OF MATERIALS
ADSP-TS101S EZ-KIT LITE SCHEMATIC
Title Page .................................................................................... B-1

CONTENTS
viii ADSP-TS101S EZ-KIT Lite Evaluation System Manual
Processor A ................................................................................... B-2
Processor B ................................................................................... B-3
SDRAM and Flash ....................................................................... B-4
Audio Interface ............................................................................. B-5
Audio In Amplifiers ...................................................................... B-6
Audio Out Amplifiers ................................................................... B-7
Push Buttons and LEDs ................................................................ B-8
Configuration ............................................................................... B-9
Expansion Connectors ................................................................ B-10
Power Supply .............................................................................. B-11
Caps ........................................................................................... B-12
INDEX

ADSP-TS101S EZ-KIT Lite Evaluation System Manual ix
PREFACE
Thank you for purchasing the ADSP-TS101S EZ-KIT Lite®, Analog
Devices (ADI) evaluation system for TigerSHARC®floating-point
embedded processors.
The TigerSHARC processor is a static super scalar (SSS) architecture tar-
geted at software-defined radio applications. In these wireless
infrastructure applications, the TigerSHARC processor is replacing
field-programmable gate arrays (FPGAs) in the chip rate processing appli-
cations for third generation cellular. The performance, flexibility,
multiprocessing and IO capabilities of the TigerSHARC processor makes
it superior to FPGA implementations.
The evaluation board is designed to be used in conjunction with the Visu-
alDSP++®development environment to test the capabilities of the
ADSP-TS101S TigerSHARC processor. The VisualDSP++ development
environment gives you the ability to perform advanced application code
development and debug, such as:
• Create, compile, assemble, and link application programs written
in C++, C, and ADSP-TS101S assembly
• Load, run, step-in, step-out, step-over, halt, and set breakpoints in
application program
• Profile programs
• Read and write data and program memory

x ADSP-TS101S EZ-KIT Lite Evaluation System Manual
• Read and write core and peripheral registers
• Plot memory
Access to the ADSP-TS101S processor from a personal computer (PC) is
achieved through a USB port or an optional JTAG emulator. The USB
interface gives unrestricted access to the ADSP-TS101S processor and the
evaluation board peripherals. Analog Devices JTAG emulators offer faster
communication between the host PC and target hardware. Analog Devices
carries a wide range of in-circuit emulation products. To learn more about
Analog Devices emulators and processor development tools, go to
http://www.analog.com/dsp/tools/.
ADSP-TS101S EZ-KIT Lite provides example programs to demonstrate
the capabilities of the evaluation board.
LThe ADSP-TS101S EZ-KIT Lite installation is part of the Visu-
alDSP++ installation. The EZ-KIT Lite is a licensed product that
offers an unrestricted evaluation license for the first 90 days. For
details about evaluation license restrictions after the 90 days, refer
to “Evaluation License Restrictions” on page 1-7.
Refer to the VisualDSP++ Installation Quick Reference Card for details.
The board features:
• Two Analog Devices ADSP-TS101S processors
D250 MHz core clock speed
DConfigurable core clock mode
• USB debugging interface
• Analog Devices AD1871 96 kHz analog-to-digital converter
(ADC)
DLine-in 3.5 mm stereo jack