AndyMark Robot Competition Table User manual

AndyMark Robot Competition Table Assembly Guide v1.0 10/7/20
Included Parts & Hardware
Required Tools
Mallet
1/8” Allen Wrench
#2 Phillips Screwdriver
4X - Outer Section Wall
2X - Inner Section Wall
1X - East Wall
1X - West Wall
4X - Flat Head Screw
30X - Washer
22X - Spacer
2X - Outer Panel1X - Inner Panel
8X - Dowel
1. Insert Dowels into Outer Panels
Locate the two Outer Panels and 8 Dowels. Using a mallet or Light Duty Hammer, gently insert dowels into
holes on the edge of each Outer Panel. Approximately half the dowel should protrude when fully inserted.
The inner panel does not recieve any dowels.
x8
For more information visit AndyMark.com/Table
30X - Screw
2X - Interconnect A
2X - Interconnect B

Interconnect A
Outer Section Panel
Outer Section Side Wall
Interconnect B
Outer Section Side Wall
West Wall
2. West Section Assembly
1X - Interconnect A
1X - Interconnect B
2X - Outer Section Side Wall
1X - West Wall
1. Align walls to the corresponding edges of panel with the
at side of the panel facing up. Each hole in the panel
should line up with a corresponding hole or threaded insert
in each wall.
1X - Outer Panel
For more information visit AndyMark.com/Table
12X - Washer
12X - Screw 8X - Spacer
2. Insert the Interconnects into the walls so that it lines up
with the holes in the wall and panel. Make sure the back of
the angle is facing towards the inside of the table. Use a
screw and washer to secure the wall and Interconnect to
the panel. Leave these screws loose until all screws are
installed.
3. Add a screw, washer and spacer to each of the remaining
panel holes. Thread the screw into the threaded inserts in
each side wall and leave loose until all the screws are
installed.
Screw
Outer Section Side Wall
Washer
Interconnect B
Screw
Spacer
Washer
4. Adjust the walls and ensure the outside edges of each wall
are aligned with the edge of the base panel. Using an 1/8”
allen wrench, secure wall sections to the base panel.

Inner Section Panel
Inner Section Wall
Inner Section Wall
3. Center Section Assembly
2X - Inner Section Wall 1X - Inner Panel
For more information visit AndyMark.com/Table
6X - Washer
6X - Screw 6X - Spacer
1. Align walls to edges of the inner panel with the at side
of the panel facing up. Each hole in the panel should line
up with a corresponding hole or threaded insert in each
wall.
2. Add a screw, washer and spacer to each of the 6 large panel
holes. The 4 holes on the edge will be used in a later step.
Thread the screw into the threaded insert and leave loose
until all the screws are installed.
Screw
Spacer
Washer
3. Adjust the walls and ensure the outside edges of each wall are aligned with the edge of the base panel. Using an
1/8” allen wrench, secure wall sections to the base panel.

4. East Section Assembly
For more information visit AndyMark.com/Table
1X - Interconnect A
1X - Interconnect B
1. Align walls to edges of panel with the at side of the
panel facing up. Each hole in the panel should line up with
a corresponding hole or thraeded insert in each wall.
1X - Outer Panel
12X - Washer
12X - Screw 8X - Spacer
2. Insert the Interconnects into the walls so that it lines up
with the holes in the wall and panel and the back of the
angle is facing towards the inside of the table. Use a screw
and washer to secure the wall and Interconnect to the
panel. Leave these screws loose until all screws are
installed.
3. Add a screw, washer and spacer to each of the remaining
panel holes. Thread the screw into the threaded insert and
leave loose until all the screws are installed.
Screw
Outer Section Side Wall
Washer
Interconnect B
Screw
Spacer
Washer
4. Adjust the walls and ensure the outside edges of each wall
are aligned with the edge of the base panel. Using an 1/8”
allen wrench, secure wall sections to the base panel.
2X - Outer Section Side Wall
1X - East Wall
East Wall
Outer Section Side Wall
Interconnect B
Outer Section Panell
Outer Section Side Wall
Interconnect A