During the months that the risk for fire is high we highly recommend to consult the firefighting administrations of
your area before you will use the device.
In case you will notice unusual rise of temperature of the device or dark in color vapor:
1) Keep distance from any flammable materials
2) Disconnect the battery
3) Leave the device in a stand up position on a fire proof horizontal surface
4) Ideally block the exit of the lid with a wet piece of waving or paper, this will speed up the cease of
combustion
5) Leave the device to be cold before you open the lid
6) Follow the directions in the chapter “DEVICE”
Instructions for safe use
•The body of the device (2) and its base, the lid (3) and the point where the resistance enters the fire chamber (6) are
extremely hot, do not come in contact with these parts without protection.
•When the device is hot only touch the bottom or the lid from the special handles and even then check the temperature
levels first.
•Always wear heat resistant gloves during use (leather beekeeping gloves are suitable).
•The CS and VPs are designed to work safely when the device is in a horizontal to 45οangle in the forward position. Do
not tilt the device beyond this angle, either forward or backward, as very hot particles may fall out of the air inlet or the
nozzle.
•Do not place more Cool Smoke or Vapor Pads in the fire chamber than is recommended. The excess amount blocks the
smoke while there is a risk of overheating and exceeding the safety limit of the materials’ non-flammable characteristic
resulting in pyrolysis and instantaneous flame that may cause a fire.
•The device and materials have undergone extensive safety tests with absolute success. Nevertheless, consideration
must be given to the possibility of the device being exposed to unforeseen conditions (unintentional contact with
flammable materials, e.g., gasoline, etc.). If a flame appears for any reason, place the device on a horizontal fireproof
surface without pressing the bellow. To extinguish the flame faster, cover the nozzle (e.g., with wet paper or cloth). The
device will put itself out in 5-30 minutes.
•Avoid bringing metal into contact with the battery or charger terminals. You will cause irreparable damage to the
charger, and you may destroy the batteries.
•The vapor-smoke residues are very hot and can cause burns or a fire when they come into contact with flammable
materials. Avoid any contact with body parts or flammable materials until they have cooled down.
•Use suitable batteries only. Batteries with different characteristics may destroy the resistance, the circuits, and the
device and/or exceed temperature safety levels resulting in a flame or fire. Smaller batteries will produce insignificant
or no smoke.
•When in operation, the resistance is extremely sensitive. Do not apply powerful force as you will damage it.
•The resistance reaches high temperatures and there is the risk of severe burns; therefore, avoid any contact with body
parts or flammable materials when it is hot.
•If you notice bare - damaged wires in the circuit of the charger or device, do not use them and return them for repair to
the reseller, or to ANEL.
•Always use the suitable chargers with the appropriate adapters. Unsuitable chargers may destroy your battery or not
charge properly.
•In the event that you have followed the preparation instructions (battery charging and testing, resistance operation),
but vapor-smoke is not produced, contact the ANEL’s technical support department or your reseller.
•The device is not waterproof; it is not allowed to come into contact with water. If it gets wet, blow with compressed air
in all places, open the fuse box, remove the fuse, and blow there too. Operate the device again only when you are
absolutely sure that all its parts are dry. There is danger of a short circuit.
•The device, batteries and charger are not manufactured to withstand falls and collisions. A fall or collision may destroy
parts or all the device and accessories, therefore handle it with care.
•If a problem arose from a fall or collision to the device, batteries, or the charger.
•Batteries are attached to the device with a Velcro strap. If the Velcro is damaged or worn, the battery may not secure
well and detach from the device and hang from the adapter, thus establishing the device unsafe. If the Velcro of the
battery casing is worn, contact the reseller or ANEL for a new one.
•The device has points that may injure you if you use it with bare hands. Always use beekeeping gloves when handling
the device.
•The batteries must be charged in a controlled environment because the event of material failure, over voltage, etc.;
there is a risk of self-ignition and fire and the risk of burning materials being displaced. When charging these batteries
place them on a fireproof surface.
