Antarctic Star HZB-12/B User manual

Antarctic Star
PORTABLE AUTOMATIC ICE MAKER
User Manual
IV
HZB-12/B

IMPORTANT SAFETY INSTRUCTIONS.
.2
PREPARING YOUR ICE MAKER FOR USE
, IMPORTANT SAFETY TIPS
GETTING TO KNOW YOUR UNIT.
.4
OPERATING PROCEDURES & MAINTENANCE
.6
UNPACKING YOUR ICE MAKER,
.6
CONNECTING YOUR ICE MAKER.
.6
CLEANING AND MAINTAINING YOUR ICE MAKER.
.7
USING YOUR ICE MAKER.
,7
TROUBLESHOOTING,
.8
TECHNICAL PARAMETERS & CIRCUIT DIAGRAM.
,9
EXPLOSIVE DRAWINGS.
1
TABLE OF CONTENTS

Your safety and the safety of others are very important.
This is the safety alert symbol:
All safety messages will follow the safety alert symbol and the word “ DANGER" or “ WARNING".
r
I
These words mean:
You can be killed or seriously injured if you don ’ t immediate follow instructions.
• Unplug the ice maker before cleaning or making any repairs or servicing.
• Exercise caution and use reasonable supervision when appliance is used near children.
2
PREPARING YOUR ICE MAKER FOR USElRRININKEEHKR
WARNING-
We have provided many important safety messages manual and your appliance.
Always read and obey all safety messages,
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance
of injury, and tell you what can happen if the instructions are not followed.
When using electrical appliances, basic safety precautions should be followed to reduce the
risk of fire, electric shock, and injury to persons or property. Read all instructions before using
any appliance.
• Do not operate this, or any other appliance with a damaged cord.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent
or a similarly qualified person in order to avoid a hazard.
This ice-maker must be positioned so that the plug is accessible .
Connect to properly polarized outlets only. No other appliance should be plugged into the
same outlet. Be sure that the plug is fully inserted Into the receptacle.
• Do not run the power cord over carpeting or other heat insulators. Do not cover the cord.
Keep cord away from traffic areas, and do not submerge in water.
• We do not recommend the use of an extension cord, as it may overheat and become a risk
of fire. If you must use an extension cord, use No.14AWG minimum size and rated no less
than 1875 watts.
7?

• Do not use other liquid to make the Ice-cube other than water.
• Do not tip over.
DANGER - Risk Of Fire Or Explosion. Flammable Refrigerant Used. To Be
Repaired Only By Trained Service Personnel. Do Not Puncture Refrigerant Tubing.
• If the unit is with problem need to be maintained, that replacing with like components and
that servicing shall be done by factory authorized service personnel, so as to minimize the
risk of possible ignition due to incorrect parts or improper service.
• CAUTION - Risk Of Fire Or Explosion. Dispose Of Property In Accordance With Federal
Or Local Regulations. Flammable Refrigerant Used .
• CAUTION-Risk Of Fire Or Explosion Due To Puncture Of Refrigerant TubingjFollow
Handling Instructions Carefully. Flammable Refrigerant Used.
• The ice maker should be installed in accordance with the safety standard for Refrigeration
Systems, ASHRAE15. The ice maker shall not be installed in corridors or hallways of
public buildings.
• If the ice maker is brought in from outside in wintertime, give it a few hours to warm up to
room temperature before plugging it in.
WARNING. This appliance must be earthed.
• Do not use your ice-maker outdoors. Place the ice-maker away from direct sunlight and
make sure that there is at least 4 inches of space between the back of your unit and wall.
Keep a minimum distance of 4 inches on each side of your unit free.
DANGER - Risk Of Fire or Explosion. Flammable Refrigerant Used. Do Not Use
Mechanical Devices To Defrost Ice Maker. Do Not Puncture Refrigerant Tubing.
CAUTION - Risk Of Fire Or Explosion. Flammable Refrigerant Used. Consult Repair
Manual/Owner ’ s Guide Before Attempting To Install or Service This Product. All Safety
Precautions Must be Followed.
• Do not clean your ice maker with flammable fluids. The fumes can create a fire hazard or
explosion.
IMPORTANT:
The wires in this mains lead are colored in accordance with the following code:
Green or Green with a strip yellow: Grounding
White: Neutral
Black: Live
To avoid a hazard due to instability of the appliance, it must be placed at an even or flat
surface.

1
2
4
General instrucion
1. Ice scoop.
2. Ice full sensor
. Ice basket
4. Top cover with transparent window
5. Air exhausting
6. Water drain cap: at front btm side of the unit.
7. MAXIMUM WATER LEVEL: ------------ ▲ -------------
Remove the ce basket, you can see the water level mark.

Postion of control panel & function
E
F
5
OPERATING PROCEDURES & MAINTENANCE
I
i
CONTROL
PANEL
o
w
O
L
Control Panel: Easy to use, visible functions touch display setting.
A. Selected ice size displaying: Small and Large.
B. Power indicator
C. Ice-Full indicator
D Water shortage indicator
E. Button to turn on/off the unit.
F. Button to select ice cube size.

UNPACKING YOUR ICE MAKER
1.
CONNECTING YOUR ICE MAKER
L
CLEANING AND MAINTAINING YOUR ICE MAKER
Before using your ice maker, it is strongly recommended to clean it thoroughly.
4.
6
A DANGER
5.
6.
1.
2.
.
1. This unit should be properly grounded for your safety. The power cord of this appliance is
equipped with a three-prong plug which mates with standard three prong wall outlets to
minimize the possibility of electric shock.
2. Plug your appliance into an exclusive, properly installed, grounded wall outlet Do not under
any circumstances, cut or remove the third (ground) prong from the power cord. Any
questions concerning power and/or grounding should be directed toward a certified
electrician.
. This appliance requires a standard 110-120volt, 60Hz electrical outlet with three-prong
ground.
4.
5.
2.
.
* Improper use of the grounded plug can result in the risk of electrical shock. If the
power cord is damaged please call our customer service.
Take out the ice basket.
Clean the interior with diluted detergent, warm water and a soft cloth.
Then use the water to rinse the inside parts, and drain out the water by unplugging the
drain cap on front bottom side.
The outside of the ice maker should be cleaned regularly with a mild detergent solution and
warm water.
Dry the interior and exterior with a clean soft cloth.
When the machine is not to be used for a long time, drain water completely & dry the
interior.
Remove the exterior and interior packaging. Check if ice basket and ice scoop inside. If any
parts are missing, please contact our customer service.
Remove the tapes for fixing ice shovel, ice basket & ice scoop. Clean the tank & ice basket.
Put the ice maker on a level & flat counter top without direct sunlight and other sources of
heat (i.e.: stove, furnace, radiator). Maker sure that there is at least 4 inches gap between
the back & LH/RH sides with the wall.
Allow one hour for the refrigerant fluid to settle before plugging the ice maker In.
The appliance must be positioned so that the plug is accessible.
WARNING: fill with potable wa er only. Only use drinking water.

3
1
7.2^
Lack of Water.
"Ice ” indica or is on. Ice is full In basket.
Ice cubes s ick oge her.
in
Verify by a qualified technician.
Verify by a qualified technician.
7
XUS/NGYOUKifCEMAKEi
Ice making cycle is normal
bu no ice formed.
The Ice making cycle is
too long.
or
in
“ Add Wa er ” indica or is
on.
1. Open the cover, remove the ice basket and pour water into tank.
Keep water level below the water level mark.
2. Press “ Power" button on the control panel to begin the ice making cycle.
. Select the ice cube size by pressing the “ Select" button. If the room temperature is lower
than 60 ’ F, it is recommended to select small ice cube in order to avoid ice sticking together.
4. The ice making cycle lasts approx. 6 to 1 minutes, depending on seletion of ice cube size
and the room temperature. The recommended room temperature is 50 ’ F to 105 °F
5. If water pump can't inject water, the ice maker will stop automatically, and the “ Add Water"
indicator will be on.Press “ Power" button, fill water up to the max. water level mark and
press “ Power ” button again to turn on the unit again.Allow the refrigerant liquid inside the
compressor at least minutes to settle before restarting.
6. The ice maker stops when the ice basket is full and the “ Ice" indicator will be on. Warning:
Direc sunligh or sunligh reflec ion may cause infared sensor malfunc ion. If he
uni doesn ’ s op even ice cubes obs ruc sensor, move he uni where no sunligh .
7. Change water In the water reservoir every 24 hours to ensure a reasonable hygiene level.
If uni isn' to be used, drain all the water and dry the tank.
Stop the ice maker, fill water, and
press “ Power ” button again to
restart the unit. ____________________
Remove ice from ice basket.
Con inuous press "Selec ” bu on
5 seconds, he uni could make
ice 10 cycles even "Ice" indica or
is on. ____________________________
Stop the ice maker, and restart it
when the ice blocks melt. Select the
small size ice cube selection. _______
Replace the water. Temperature of
water recommended at 40°F-90 c F
The room temperature should be 50
*F-105 ‘ F, water temperature should
be 40°F-90°F
Water temperature
inner tank is too low.
Room temperature
water temperature
inner tank is too high.
Refrigerant in cooling
system leaks.
Pipe in the cooling
system is blocked.

Model
HZB-12/B
Protection Type
I
Power
115V/60HZ
Ice Making Current
1.7A
Ice Harvest Current
2.0A
Refrigerant
R600a 0.74Qz/21g
Design Pressure
High Side
290Psig
Low Side
88Psig
Vesicant
C5H10
Net Weight
7.1 Kg
Dimension (W'D ’ H)
222x 1 x 20mm
Enclosure
Plastic
6C
o
o
CN5
1
T1
MCU
WATER
T1
RELAY
AC-N
o
o
VALVE
DC WATER PUMP
COMP
LED2S
SM
^SELECT
-I
AC-L
-FAN+
WATER LEVEL
DETECTING
! CON'D TEMP
SENSOR
DC FAN
MOTOR
INFRARED
SENSOR
DETECTOR
MICRO SWITCH
MICRO SWITCH
OPERATION PC
POWER o LED3?
o ---
I Overload ____
•T-Protfcctor shove]
ELECTRICAL DIAGRAM
MAIN CONTROL PCB
+PUMP-
ft
POWER
SUPPLY
5 pCN7
Motor For Ice
•Solenoid
Valve
COMP MOTOR
-I H
WATER &
ON/OFF [p]
Lelay

J
15
14,
24
1 '
25
12
26
S/N
Part description S/N
Part description
S/N
Part description
1
20
1
1
4
1
9
EXPLOSIVEDRAWINGS
1
2 s
Qty
/Per
1
J _
J _
J _
1
2
2
2
2
2
1
1
2
4
5
6
7
8
9
10
11
12
13
14
Power cord
plastic clip
Back panel
Plate back support
Evaporator
Control box cover
21
22
23
24
25
26
27
28
Ice scoop
Back btm panel
Back top panel
Touch pad _________
Displaying PCB
Bracket displaying
Clear window
Front top panel
Front btm panel
Ice shovel
Foaming asm
Ice basket ________
Stainless wire
Inner tank brackt, RH
29
0
2
2
Qty/
Per
2 _
J _
J _
1 ___
1
Main PCB ________
Control box
Magnetism valve
Ice making box
Micro switch
Cam
Inner tank bracket, LH
Ice scoop link
1
2
J
£
2_
2_
2
15
16
17
18
19
35
36
37
38
39
40
41
42
Water filter ________
Sychronuous motor
Condenser ________
DC Fan motor _____
Copper tube filter
Nylon plug drain
Water Supply pipe
Silicon pump sealing
DC water pump
Compressor _______
Plate bottom _______
Rubber foot _______
Air grille __________
Internal Wire
2_
2
2_
2_
2_
2_
2_
1
Qty/
Per
2 _
2 __
2 _
2 _
1

'4
10

IMPORTANT
AVIS
IMPORTANTE
Thank you for purchasing this product! If you have questions about assembly or operation of this
product, are missing parts, or if the product is damaged, please contact us via Amazon Message or call
customer serve Phone; 213-4467172
No devuelva este producto a la tienda.
Solo hay que llamar nuestro departamento de servicio
al cliente en caso de tener preguntas o inquietudes:
213-4467172
(8: 0am - 5: 0pm P.S.T.)
SE REQUIERE PRUEBA DE COMPRA CON FECHA PARA SERVICIO BAJO GARANTfA.
Ne pas retourner ce produit au magasln.
Veuillez appeler le service la clientele pour toutes questions au:
21 -4467172
(8: 0am - 5: 0pm P.S.T.)
PREUVE D'ACHAT ORIGINALE REQUISE POUR SERVICE DE GARANTIE.
Do not return this product to the store.
Simply call our customer service department for any questions or concerns:
21 -4467172
(8: 0am - 5: 0pm P.S.T.)
DATED PROOF OF PURCHASE REQUIRED FOR WARRANTY SERVICE.
dd:9733 Topanga Canyon Blvd. APT310, Cha swor h, CA 91311
NMMVMMMaifp Phone: [phone]