Antec controls LUME20 User manual

LUME20
Room Pressure Monitor
MANUAL v100

LUME20 - MANUAL
2 | LUME20 – Manual | AntecControls.com
TABLE OF CONTENTS
INTRODUCTION ...............................................................................................................................................................................4
General..........................................................................................................................................................................................4
Product Overview..........................................................................................................................................................................4
General Installation Information ....................................................................................................................................................4
Technical Specifications ................................................................................................................................................................5
GETTING STARTED WITH LUME20.................................................................................................................................................6
In the Box......................................................................................................................................................................................6
LUME ACCESSORIES ......................................................................................................................................................................7
Differential Pressure Sensor (SDPT) .............................................................................................................................................7
Door Contact Switch (DCS)...........................................................................................................................................................7
MECHANICAL INSTALLATION ........................................................................................................................................................8
Installation and Mounting Instructions ..........................................................................................................................................8
Pressure Sensor Installation Instructions....................................................................................................................................10
ELECTRICAL INSTALLATION.........................................................................................................................................................12
Sample Wiring Diagram...............................................................................................................................................................12
BACnet MS/TP Network .............................................................................................................................................................13
DISPLAY NAVIGATION...................................................................................................................................................................14
Initial Setup .................................................................................................................................................................................14
Home Screen ..............................................................................................................................................................................16
SETTINGS .......................................................................................................................................................................................21
Mode Override ............................................................................................................................................................................21
Room Modes ..............................................................................................................................................................................22
Monitored Rooms .......................................................................................................................................................................25
Inputs ..........................................................................................................................................................................................28
Outputs .......................................................................................................................................................................................34
BACnet........................................................................................................................................................................................37
BACnet Polling Points .................................................................................................................................................................38
User Preferences ........................................................................................................................................................................42
LUME ASSISTANT..........................................................................................................................................................................43
System Requirements ................................................................................................................................................................43
Installation Requirements............................................................................................................................................................43
How to Connect to LUME20.......................................................................................................................................................44
LUME Assistant Start-Up ............................................................................................................................................................44

LUME20 - MANUAL
3 | LUME20 – Manual | AntecControls.com
Home ..........................................................................................................................................................................................45
Diagnostics..................................................................................................................................................................................46
Adjusting Windows Defender™ Firewall Settings ......................................................................................................................47
MAINTENANCE ..............................................................................................................................................................................51
Replacement Parts......................................................................................................................................................................51
Technical Support........................................................................................................................................................................51
APPENDIX A ...................................................................................................................................................................................52
Lume™ Drywall Cut-Out .............................................................................................................................................................52

LUME20 - MANUAL
4 | LUME20 – Manual | AntecControls.com
INTRODUCTION
General
In this manual, you will find information regarding:
•LUME20 technical specifications
•LUME20 mechanical and electrical installation
•LUME20 interface navigation and configuration
•LUME Assistant software navigation and operation
Product Overview
LUME20 is designed to provide ease of use pressure
monitoring.
The Home screen provides monitoring information in a
simple format displaying information including Room Status
and Pressure Mode.
Upon swiping the screen to the left, room pressure
measurement is visually available.
Some of the key LUME20 features include:
•4.3 in. (109 mm) capacitive touchscreen display
•Password protected menus
•Configurable audible and visual alarms
•Interface with analog pressure sensor
•Native BACnet MS/TP
•Setup Wizard provides fast, intuitive start-up
•Easy to use software to copy and paste
configurations
•LED sidebars offer 180˚ viewing of current room
status
General Installation Information
1. A qualified person must perform installation and
electrical wiring in accordance with all applicable
codes and standards, including fire-rated
construction practices.
2. Do not damage electrical wiring and other hidden
utilities while installing this device.
3. Disconnect power at the service panel before
performing wiring or maintenance on this device.
4. Intended for indoor installation only, in areas with
Pollution Degree 2.
5. Not designed for use in industrial, farming or
humid environments.
6. Not designed for use in residential environments
and may not have adequate protection to radio
interference.
7. Not designed to operate in a construction
environment. Use in these environments may lead
to excess or unintended wear, reducing product
life and/or performance.
8. The manufacturer assumes no responsibility for
personal injury or property damage resulting from
improper handling, installation, service or operation
of the product.
CAUTION
This mark indicates an important point for the proper
function of LUME20 and its accessories. Pay close attention
to all caution points throughout this manual.
For local area support, please contact your local Antec
Controls Representative.
For more information visit
www.AntecControls.com

LUME20 - MANUAL
5 | LUME20 – Manual | AntecControls.com
Technical Specifications
Environmental (Operating) 32°F to 130°F (0°C to 55°C), 5% to 95% R.H. (Non-Condensing)
Environmental (Storage) -22°F to 158°F (-30°C to 70°C), 0% to 95% R.H. (Non-Condensing)
Input Power 24 VAC ±10%, 50/60 Hz, 21 VA Max (excluding external loads), Class 2
Inputs
4 Universal Inputs
Binary Input (Contact Closure)
Analog Input (0 – 10 VDC)
Thermistor Input (10k Type 2)
3 RJ45 Network Ports
Outputs
1 Analog Output (0 – 10 VDC, Max: 10 mA)
2 Binary Outputs, Non-Isolated Contact Closure (Max: 24 VAC, 500 mA)
Indicators Touchscreen Display, 4.3 in. (109 mm) TFT, Speaker
Housing UL 94V-0, PC-ABS Plastic
BACnet
Device Type B-AAC
Communication Type MS/TP (RS-485)
Communication Speed 9600, 19200, 38400, 76800
Certification BTL
Control Priority Order 1. BACnet
2. Normal operation

LUME20 - MANUAL
6 | LUME20 – Manual | AntecControls.com
GETTING STARTED WITH LUME20
In the Box
Room Pressure Monitor (LUME20)
Component
Quantity
Description
Room Pressure Monitor
(LUME20)
1
Single LUME20
[Optional] Differential Pressure Sensor (SDPT)
Component
Quantity
Description
Differential Pressure
Sensor
1 (single room monitoring)
2 (dual room monitoring)
3 (triple room monitoring)
Single SDPT
[Optional] Stainless Steel Sensor Plate
Component
Quantity
Description
Stainless Steel Sensor
Plate
2 (single room monitoring)
4 (dual room monitoring)
6 (triple room monitoring)
Stainless Steel Plate used as a
pressure sensor inlet
Mounting Hardware
Packet
2 (single room monitoring)
4 (dual room monitoring)
6 (triple room monitoring)
Packet containing two screws
for J-Box mounting of Sensor
Plate
Kink Resistant Air Tubing -
96 in. (2.44 m)
1 (single room monitoring)
2 (dual room monitoring)
3 (triple room monitoring)
Air pressure tubing to connect
between Sensor Plate and
Room Pressure Sensor
OR
[Optional] ABS Sensor Plate
Component
Quantity
Description
ABS Sensor Plate
2 (single room monitoring)
4 (dual room monitoring)
6 (triple room monitoring)
ABS plate used as pressure
sensor inlet
Mounting Hardware
Packet
2 (single room monitoring)
4 (dual room monitoring)
6 (triple room monitoring)
Packet containing two screws
and two drywall anchors for wall
mounting of Sensor Plate
Kink Resistant Air Tubing -
96 in. (2.44 m)
1 (single room monitoring)
2 (dual room monitoring)
3 (triple room monitoring)
Air pressure tubing to connect
between Sensor Plate and
Room Pressure Sensor
CAUTION
Please ensure you have all the components before proceeding. Inspect all components for shipping damage. Do not install any components that appear
damaged. Contact your local Antec Controls Representative for replacements.
For the latest information and videos please visit www.AntecControls.com.

LUME20 - MANUAL
7 | LUME20 – Manual | AntecControls.com
LUME ACCESSORIES
Differential Pressure Sensor (SDPT)
The SDPT is a room pressure sensor that is used to measure pressure.
Overview
See the SDPT product submittal on AntecControls.com for Specifications, Dimensions and Configurations.
Options
1. Differential Pressure Sensor
Model:
Features:
SDPT
•2 – 10 VDC outputs for pressure reading.
•-0.25 to +0.25 in.w.c. (-60 to 60 Pa)
•LED light used to display status
•Accurate to 3% of reading
Door Contact Switch (DCS)
Door Contact Switches can be wired into the binary input(s) to detect when the door(s) are open.
Overview
See the DCS product submittal on AntecControls.com for Specifications, Dimensions and Configurations.
Options
1. Surface Mount 2. Flush Mount

LUME20 - MANUAL
8 | LUME20 – Manual | AntecControls.com
MECHANICAL INSTALLATION
It is recommended to mount LUME20 at approximately 5 feet (1. 5 m) from the floor. This will allow the interface to be at an
appropriate height for use during setup and during normal operation.
Installation and Mounting Instructions
Touchscreen Installation Instructions
Option A
Mount LUME20 directly on dry wall.
STEP 1
Mark an appropriate mounting location for the monitor.
STEP 2
Using a jigsaw, cut four lines to cut-out a rectangle (minimum 2.0 in. W X 2.5 in. H,
50.8 mm W X 63.5 mm H).
NOTE: Ensure the cut-out sizes are not bigger than the size of the back plate (3.4
in. W x 4.9 in. H, 86.4 mm W X 124.5 mm H ).
STEP 3
Drill 4 mounting holes according to the provided template in Appendix A.
STEP 4
Make sure that the anchors are flush to the wall and then mount the backplate on
the drywall using four #6 drywall screws with anchors.
STEP 5
Attach LUME20 on the backplate installed on the dry wall.
Option B
Mount LUME20 using an EU Wall box.
STEP 1
Using the provided instructions, mount the EU Wall box at the suggested height from
the floor.
STEP 2
Remove the two unused screws from both sides.
STEP 3
Mount the back plate on the wall box using the two screws removed from the wall
box in Step 2.
STEP 4
Attach LUME20 on the backplate that was installed in Step 3.

LUME20 - MANUAL
9 | LUME20 – Manual | AntecControls.com
Option C
Mount LUME20 using a standard single-gang electrical box.
STEP 1
Using the provided instructions, mount the standard single-gang electrical box at the
suggested height from the floor.
STEP 2
Mount the back plate to the box using two #8-32 screws.
STEP 3
Attach LUME20 on the backplate that was installed in Step 2.

LUME20 - MANUAL
10 | LUME20 – Manual | AntecControls.com
Pressure Sensor Installation Instructions
Selecting a Location for Installation
There are three components that are to be installed for each
space that requires pressure monitoring:
1. A sensor plate inside the room
2. A sensor plate outside the room
3. An SDPT differential pressure sensor
Begin by determining installation locations for each of these
components.
1. The best installation location for the sensor plates is
typically above a doorway. When determining the
location for the sensor plates:
a. Ensure that nothing can be placed in front of the
pressure sensor, blocking its ability to measure
the room pressure accurately.
b. Be wary of diffuser placement in relation to the
sensor. Turbulent airflow passing over the sensor
plate can cause unstable pressure readings.
2. The Differential Pressure Sensor (SDPT) can be
mounted in the plenum space either in the room or in
the reference space. Important notes:
a. The sensor must be placed in a location where
the ninety-six inches (96 in., 2.44 m) of total
pressure tubing provided with the SDPT can
reach both pressure plates.
b. The sensor should be easily accessible for wiring
and setup.
CAUTION
Incorrect placement can affect the sensor’s readings.