Anytek z1 User manual

1
◆Forward
Thanks for purchasing our car dvrs.
Please read the manual carefully before using it to
ensure the correct use of the product. Keep the manual
properly for future needs.
◆Copyright infringement warning
Please note that this product is for personal use only, and
its use should not violate international or domestic
copyright laws and regulations. Even if the recorded
images are for personal use only, please note that in
some cases the use of this product to record images of
performances, exhibitions or commercial activities may
infringe upon the copyright or other legal rights of others.
◆Matters needing attention
- Do not unlawfully open or disassemble this product,
which may lead to electric shock or equipment damage. If
necessary, please leave it to the service center or
professionals.
- This product can be used for other purposes, such as
photography, self-timer, etc.

2
- Do not stack items on this product, do not press the
screen, otherwise it may lead to screen damage.
- Do not operate this product during driving, so as not to
distract attention and affect driving safety.
- Do not touch the screen with sharp objects to avoid
damaging the screen.
- Do not let children play with the device.
- When the car is charged from the cigarette lighter
socket in the boot state, the equipment will be shut down.
If you have the following information, please contact the
purchasing office or service center.
- the Charger damaged or connection broken.
- Shell damage, transformer damage, or exposure of
internal components.
Please note that the charger itself also consumes
electricity. If not in use, please pull the car charge out of
the cigarette lighter to avoid discharging the car battery.
◆Working conditions
- Do not expose the product to the environment with
excessive dust density, so as to avoid the lens and other

3
parts contaminated with dust affecting the photographic
effect.
- Do not expose this product to rain or humid
environment. This product does not have waterproof
function.
- Avoid falling and violent impact.
- This product and its accessories are far away from
flammable, explosive, corrosive liquids or gases. Do not
discard this product at will. This machine carries batteries.
It is forbidden to discard this product into the fire in order
to avoid explosion.
- When cleaning the equipment, please remove it from
the bracket first. Clean screen and equipment surface
with soft wet cloth.
- Do not disassemble, modify or repair the equipment by
yourself. This may lead to equipment damage. Please
send it to a special authorized service center for
maintenance.
◆Temperature and humidity
The normal working temperature of the equipment is + 0.

4
—— +40 °, humidity 10% —— 80%.
Please place the equipment in a safe position.
◆Transport
- Sudden changes in temperature or humidity may cause
moisture to condense in the machine, which may lead to
short-circuit of the equipment.
- Protect the machine from dust or collision during
transportation.
- When transporting equipment, please use the original
packing as far as possible.
◆Vehicle-mounted adapter (car charging)
On-board adapters can be used in your on-board
cigarette lighter socket(DC12 or 24V).
◆Basic function of recorder
1. High Definition Picture Video of 1080@30fps Front
Camera.
2. Rear camera1080@30fps High Definition Picture
Video.
3. 6G Multilayer Filter Resolves 170 Degree Extra Wide
Angle Lens.

5
4. 2.35 inch MIPI HD screen（480*320）.
5. G+G Capacitance Touch Screen for Full Screen
Touch.
6. Starlight night vision sensor.
7. WDR Wide Dynamic Processing Technology.
8. Start synchronously.
9. Support loop recording.
10. Collision file lock protection.
11. Rear camera Full screen display without delay.
12. Capacity not less than 8G, TF card maximum support
32GB.
【Note】Please use a high-speed TF card (Class 10 or
above), capacity not less than 8G, TF card maximum
support 32GB. For the first time using SD, please format
SD card on this machine.
Operation instructions
Operation interface
Appearance

6
1
Power
interface
2
Power
Indicator
Lamp
3
camera
4
Rear
camera
interface
5
display
6
TF cards
slot
7
Power
button
8
Reset hole
9
Mic

7
Button function
Power button(PWR）：For boot（Short press）、Shutdown
（Long press）；Short-press switch screen saver in
standby state，10 seconds long reset machine
1）Touch function
2）Click anywhere on the screen and a touch interface
appears as shown in the figure.
3）ouch the lower right corner Button Enter Menu
Options.
4）Click on the top left corner The icon enters the
basic function options of camera and clicks on the menu
of requirement to set the relevant content.。
5）click icon Enter the basic menu function options,
click on the menu of requirements to set relevant content.
5）Click on the top left corner of the main interface Icon
，You can start or stop recording. Start recording
flicker.

8
6）You can open the screen saver by clicking anywhere
on the screen in the screen saver state.
Lock screen function
The system defaults to "close" setting to "1 minute" and
enters screen saver status without operation. Under
screen protection, press the power button or click
anywhere on the screen to wake up the screen saver and
enter the normal operation.
Picture-in-picture switching
Home page click Switching the front and back full
screen, you can choose three display modes: front full
screen, back full screen and picture-in-picture.二、Insert
and remove memory cards
1.Insert Memory Card: Ensure that the recorder can
store video properly
2.Remove the memory card: press the memory card
lightly, the memory card pops up
Reminder：

9
Please confirm the insertion direction of the memory card.
Incorrect insertion direction may damage the recorder
and the memory card.
Turn on and off the recorder
1.Turn on the camera
Press the power button or connect the charger, the
recorder sends out a reminder sound, LCD displays the
boot screen (default is 3 minutes of cyclic video state),
the recorder is in the standby state of video recording; at
this time, the LCD screen displays photography, cyclic
recording time, WIFI icon, and the date/time is displayed
in the upper right corner of the screen.
2.Turn off the recorder
Press and hold the power button for about 3 seconds
when the power is turned on. When a prompt sound is
heard and LOGO is displayed, the recorder is turned off.
Specific function introduction
System setup

10
When the recorder is on standby, click on the icon in the
lower right corner with the touch screen enter Video
Mode and System Settings Menu，Select the last system
settings Icon ，You can enter the system settings. The
system menu is as follows：
1）Keypad tone： ON/OFF
2）volume：off/High / medium / low，
3）Clock setting：You can modify the year, month, day and
time. You can adjust the number by the up and down
arrows on the right side of the display screen and confirm
it by checking after adjustment.
4）Language choice：English/简体中文/繁体中文
5）Scintillation frequency：50Hz/60Hz
6）Automatic closing screen：off / 1 minute / 3 minutes, the
system defaults to "off"
7）Protection sensitivity：off/High / medium / low，System
default "shutdown"
8）System reset Yes/No. Choosing "Yes" will remove all
your previous settings and restore them to the factory
default. Please choose carefully.