AOC L19W831 User manual

TABLE OF CONTENTS
FOR YOUR SAFETY ……………………………………………………… 2
PRCAUTIONS AND REMINDERS ………………………………………… 3
IMPORTANT SAFETY INSTRUCTIONS ………………………………… 5
PACKAGE CONTENTS ……………………………………………… 7
ATTACHING THE BASE …………………………………………… 7
PREPARING YOUR LCD TV FOR WALL MOUNTING ………… 8
PREPARATION ……………………………………………………………… 9
PERIPHERAL CONNECTION GUIDE …………………………………… 11
OPERATING INSTRUCTIONS …………………………………………… 13
TO USE THE FRONT PANEL CONTROL ……………………… 13
TO USE THE REMOTE CONTROL ……………………………… 14
VIEWING MODES ILLUSTRATIONS ……………………………… 15
CONNECTING EQUIPMENT ……………………………………… 16
TO USE THE MENUS ……………………………………………… 26
MAIN MENU ………………………………………………………… 26
PICTURE MENU …………………………………………………… 27
SOUND MENU ……………………………………………………… 28
ADVANCED MENU ………………………………………………… 28
PC SETUP MENU …………………………………………………… 29
INSTALLATION MENU……………………………………………… 29
SYSTEM MENU……………………………………………………… 30
TIPS …………………………………………………………………… 31
PRODUCT SPECIFICATION ……………………………………………… 32
BEFORE CALLING SERVICE ……………………………………………… 33
GLOSSARY ………………………………………………………… 34
ENGLISH

1
SYMBOL SYMBOL DEFINITION
SA 1965
DANGEROUS VOLTAGE: The lightning flash with
arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of
electrical shock to persons.
SA 1966
INSTRUCTIONS: The exclamation point within on
equilateral triangle to alert the User to the presence of
important operating and maintenance (servicing)
instruction In the literature accompanying the appliance.
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, Such as vases, Shall be placed on the apparatus.
Caution - Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type.
ENGLISH

2
FOR YOUR SAFETY
Before operating the TV please read this manual thoroughly. This manual
should be retained for future reference.
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE
1. The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
2. Shielded interface cables and AC power cord, if any, must be used in
order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modification to this equipment. It is the
responsibilities of the user to correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the TV to rain or moisture.
Dangerously high voltages are present inside the TV. Do not open the cabinet.
Refer servicing to qualified personnel only.
SAFETY: Lamp Disposal
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE
RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL
LAWS. FOR MORE INFORMATION, CONTACT THE ELECTRONIC
INDUSTRIES ALLIANCE AT WWW.EIAE.ORG.
ENGLISH

3
Place unit on even surfaces. Don't place the TV in confined
spaces or in a box when using it.
Unplug immediately if is malfunction
like no picture, no
video/audio,smoke and bad odor
from TV.
Unplug immediately if other foreign
materials are put inside TV box or if
the TV fell down.
Don't throw any object inside the TV
box like metals or other flammable
materials.
Prohibit/Avoid opening TV cabinet
PRECAUTIONS AND REMINDERS
ENGLISH

4
Remember to unplug the AC cord
from the AC outlet before cleaning.
Do not use liquid cleaners or aerosol
cleaners to clean the display.
Avoid direct sunlight, dusty, high
humidity and smoky areas.
Make sure to unplug the unit when
not in use for a long period of time
(days).
Call service personnel to clean the
internal part of the TV once a year.
Do not cover or block any vents and
openings. Inadequate ventilation may
shorten the life of the display unit and
cause overheating.
Do not place the display near water,
such as bathtub, washbasin, kitchen
sink laundry tub, swimming pool or
in a damp basement.
Notice for Remote Controller
Avoid Dropping Avoid Liquids Avoid Aerosol Cleaners
















ENGLISH

5
Read before operating equipment
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with
the manufacturers instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding type plug.
A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and third grounding prong. The wide
blade or third prong is provided for your safety. When the provided plug
does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from
tip-over.
13. The TV should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supplied to your
home, consult your dealer or local power company.
14. Unplug this apparatus during lightning storms or when unused for long
periods of time.
15. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
16. This product may contain lead or mercury. Disposal of these materials
may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities or the
Electronic Industries Alliance: www.eiae.org
17. Damage Requiring Service – The appliance should be serviced by
qualified service personnel when:
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a
marked change in performance; or
E. The appliance has been dropped, or the enclosure damaged.
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH

6
18. Tilt/Stability – All televisions must comply with recommended
international global safety standards for tilt and stability properties of its
cabinets design.
yDo not compromise these design standards by applying excessive
pull force to the front, or top, of the cabinet, which could ultimately
overturn the product.
yAlso, do not endanger yourself, or children, by placing electronic
equipment/toys on the top of the cabinet. Such items could
unsuspectingly fall from the top of the set and cause product damage
and/or personal injury.
19. Wall or Ceiling Mounting – The appliance should be mounted to a wall
or ceiling only as recommended by the manufacturer.
20. Power Lines – An outdoor antenna should be located away from power
lines.
21. Outdoor Antenna Grounding – If an outside antenna is connected to
the receiver, be sure the antenna system is grounded so as to provide
some protection against voltage surges and built up static charges.
Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984,
provides information with respect to proper grounding of the mats and
supporting structure grounding of the lead-in wire to an antenna-
discharge unit, size of grounding connectors, location of antenna-
discharge unit, connection to grounding electrodes and requirements for
the grounding electrode. See Figure below.
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL
ELECTRICAL CODE
Note to the CATV system installer: This reminder is provided to call the
CATV system installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that
the cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
Please, make sure to connect the power plug to the wall outlet socket
after connecting the TV to the adapter!
22. Objects and Liquid Entry – Care should be taken so that objects do not
fall and liquids are not spilled into the enclosure through openings.
ENGLISH

7
Package Contents
AOC L19W831 TV unit
Power cord
Remote control
Batteries (AAA) (Except Argentina)
Audio cable
signal cable
User manual
Quick Setup Guide
IMPORTANT: Do not apply pressure to the screen display area which may
compromise the integrity of the display. The manufacturer’s warranty does
not cover user abuse or improper installations.
Attaching the Base
IMPORTANT: The Base of the TV must be assembled prior to usage.
1. Place TV unit face down on a soft and flat surface (blanket, foam,
cloth, etc.) to prevent any damage to the TV.
2. Carefully align and insert the Base to the stand.
3. Gently push the Base towards the TV until the locking mechanism
locks into place.
ENGLISH

8
100
mm
Preparing Your LCD TV for Wall Mounting
We suggest that you keep your TV at least 2.36 inches (60 mm) from the wall
to prevent cable interference.
Before you wall-mount your TV, you need to remove the base.
To attach a wall mount bracket to your TV:
1 Remove the two T4 and two M4 screws holding your TV to the stand.
2 Remove the stand base
3 Secure the wall mount bracket to the back of your TV using four M4
screws, as indicated in the illustration.
100 mm
A
tt ach
br acket
her e
R e m o v e T 4 sc r e w s R e m o v e M 4 sc r e w s
R
em o v e st and
Note: 100mmx100mm wall mount bracket & M4 screws not included.
ENGLISH

9
Please, make sure to connect the power plug to the wall outlet socket after
connecting the TV to the power cord!
1. Install the base stand; place the TV on a solid surface.
Ensure that the TV is placed in a position to allow free flow of air. Do not
cover the ventilation openings on the back cover.
To prevent any unsafe situations, no naked flame sources, such as lighted
candles, should be placed on or in the vicinity.
Avoid heat, direct sunlight and exposure to rain or water. The equipment
shall not be exposed to dripping or splashing.
2. Connect the antenna cable or CATV cable to the aerial socket TV IN at the
back of the TV set.
PREPARATION
ENGLISH

10
3. Remote control:
Remove the cover of the battery compartment. Insert the 2 batteries
supplied (Type AAA 1.5V).
4. Power:
Insert the power cord in the wall socket having an AC power supply. You
can see LED states at the front panel. If the LED color is Blue, means the
TV set is power on. If the LED color is Redʿwhich means this TV set is in
standby state.
5. Turn the TV on:
Push the POWER key on the Remote control or the Front panel control
knobs.ʳWait a minute,ʳthe TV will power on andʳcan see the display on the
screen
POWER Key
ENGLISH

11
HDMI S-Video Composite Pr Pb Y PC Audio in 15-pin D-Sub
1. HDMI – Connect the primary source for digital video such as a
DVD multimedia player or set top box through this all digital
connector. The white color band on the rear of the TV indicates
this connection.
2. PC IN– Connect the video and audio cables from a computer
here.
PERIPHERAL CONNECTION GUIDE
ENGLISH

12
3. AV/S-VIDEO IN – Connect the primary source for composite
video devices, such as a VCR or video game. Use the white
and red connectors to connect the external audio from the same
source. The signal being carried by the S-Video cable and
connector, if connected, will take priority over the Video RCA
connector (yellow connector).
4. COMPONENT (Y Pb/Cb Pr/Cr with Audio L/R) – Connect the
primary source for component video devices such as a DVD
Player or set top box here. From left to right, use red for Pr,
blue for Pb, green for Y, red for right audio (R) and white for left
audio (L) inputs.
5. TV IN– Connect to an RF cable (out-of-the-wall, not from Cable
Box) for TV.
Once your equipment is connected, use the following procedure to view the
input signal:
Press the source button on the remote controller to select the relevant source
to view. (ex: Press VIDEO button to select “Composite Rear” if you have
connected a video recorder to Composite Rear socket.)
ENGLISH

13
TO USE THE FRONT PANEL CONTROL
1 VOL+
VOL +: Press to increase the volume. In Menu mode,
functions as right arrow to go to a next menu or increase
a setting.
2 VOL-
VOL - : Press to decrease the sound volume level. In
Menu mode, functions as left arrow to go to a previous
menu or decrease a setting.
3 CH 
CH +: Press to select the next higher Program number.
4 CH 
CH - : Press to select the next lower Program number.
5 MENU
Menu key: Press to open or exit the OSD menu.
6 INPUT
Source key: Press to select the input source.
7 POWER
Power key: Press to turn on / off (standby) the TV set.
OPERATION INSTRUCTIONS
ENGLISH

14
TO USE THE REMOTE CONTROL
PREV CH
Press to display the previous
channel .
MTS/SAP
Press to activate the TV
sounds, such as: Stereo, SAP
or Mono tone.
WIDE
Press to choose the display
aspect as: Normal, Zoom,
Cinema,Wide1 and Wide2
mode.
SOURCE
Press to display source
information.
CH-/ CH +
Press to change TV channel
up or down
EXIT
Press to exit menu or OSD.
VIDEO ADJ
Press to switch the preset of
video preset mode.
AUDIO ADJ
Press to switch the preset of
audio preset mode.
CC
Press repeatedly to select
closed caption channel or set
it off. You can set as
CC1 ,CC2 ,CC3 ,CC4 ,TT1 /
TT2,TT3,TT4 and Off
FREEZE
No support for this
product
FAV
No support for this
product
EPG
No support for this
product
V-CHIP
No support for this
product
POWER
Press to power ON/OFF (standby)
TV.(Note:TV is never completely
power off unless physically
unplugged.)
VIDEO
Press to display source menu,
then move focus by ġor Ģ, and
select by ENTER.
COMP
Press to choose Component
source mode directly.
PC/HDMI
Press repeatedly to toggle
between PC and HDMI source
modes
TV
Press to select TV source mode.
0 ~ 9 number
Press to enter channel numbers
SLEEP
Press to set sleep timer,setting a
mount of time before your TV turn
off automaticlly.(you can set as
5min /10min /15min /30min/
45min/ 60min/ 90min/ 120min/
180min /240min or Off)
VOL- / VOL+
Press + or - to adjust the volume
MENU
Press to open or exit menu.
“
ġ
”,“
Ģ
”,“
І
”,“
Ї
”,
“ENTER”
Press to adjust the various
function items on the menu.
DISPLAY
Press to show the information
about the input source or TV
channel.
MUTE
Press to mute the sound.Press
again to restore sound.
ENGLISH

15
Viewing Modes illustrations
Normal Mode on 16:10 Display screen
The original content would be at the center of the
screen.
Wide Mode on 16:10 Display screen
Wide1 and Wide2 are applied:
Wide1: The original content would fill the full
screen while the proper ratio of 16:9 content
is still maintained. Small black bars are added on
the top and bottom side.
Wide2: The original content would fill the width of the
screen while the proper ratio of 16:9 content is still
maintained. Little cropping of the content
on the sides is necessary.DŽ
ZOOM Mode on 16:10 Display screen
For those wide format images which are originally programmed into 4:3
frames with top and bottom black bars, this mode has to stretch the image in
both wide and high directions to the full display with active data. Little cropping
on sides is necessary for full display.
CINEMA Mode on 16:10 Display screen
This mode is applied to view 2.35:1 format content on 16:9 displays. To crop
both right and left sides a little for keeping the undistorted ratio of the image is
provide for users.
16:9 image in 4:3 frame Same image in ZOOM mode
Small black bars are ded on the left and
right side.
ENGLISH

16
Connection Equipment
T TO USE THE REMOTE CONTROL
Coaxial (RF)
Using Your Antenna or Cable for TV
1. Turn off the power to the TV.
2. Connect the coaxial (RF) connector from your antenna or cable
(out-of-the-wall, not from the Cable Box) to the TV IN connector
at the rear of the TV
3. Turn on the power to the TV.
4. Select TV using the INPUT button on the remote, side of the TV
or directly by pressing the TV button on the Remote Control.
Using the Antenna or Cable for your VCR
1. Turn off the power to the TV and VCR.
2. Connect the “Output to TV”, “RF Out” or “Antenna Out”
connector on the rear of your VCR to the TV IN connector at the
rear of the TV.
3. Turn on the power to the TV and VCR.
4. Select TV using the INPUT button on the remote, side of the TV
or directly by pressing the TV button on the Remote Control.
Note: If you have an off-air antenna or cable TV, connect it to the
“Antenna In” connector on the rear of
y
our VCR.
ENGLISH

17
Connecting Your TV Set-Top Box
Using HDMI
TV Set-Top Boxes that have a HDMI digital interface should be connected to
the HDMI input of the LCD TV for optimal results.
Connecting your TV Set-Top Box (Best)
1. Turn off the power to the TV and TV Set-Top Box.
2. Connect a HDMI cable to the HDMI output of your TV Set-Top
Box and the other end to the HDMI Input at the rear of the TV.
3. Turn on the power to the TV and TV Set-Top Box.
4. Select HDMI using the INPUT button on the remote, side of the
TV, or directly by pressing the PC/HDMI button on the Remote
Control.
Note:
a) The HDMI input on the TV supports High-bandwidth Digital
Content Protection (HDCP). HDCP encrypts the
transmission between the video source and the digital display
for added security and protection.
b) Refer to your TV Set-Top Box user manual for more
information about the video output requirements of the
product or consult your cable or satellite operator.
ENGLISH

18
For TV Set-Top Boxes with DVI
1. Turn off the power to the TV and TV Set-Top Box.
2. Using a HDMI-DVI cable, connect the DVI end to your TV Set-
Top Box and the HDMI end to the HDMI Input at the rear of the
TV.
3. Turn on the power to the TV and TV Set-Top Box.
4. Select HDMI using the INPUT button on the remote, side of the
TV, or directly by pressing the PC/HDMI button on the Remote
Control.
Using Component Video
Connecting your TV Set-Top Box (Better):
1. Turn off the power to the TV and TV Set-Top Box.
2. Connect the Pr (red color) connector on your TV Set-Top Box to
the corresponding Pr (red color) connector in the Component
group.
3. Connect the Pb (blue color) connector on your TV Set-Top Box
to the corresponding Pb (blue color) connector in the
Component group.
4. Connect the Y (green color) connector on your TV Set-Top Box
to the corresponding Y (green color) connector in the
Component group.
Note:
a) The HDMI input on the TV supports High-bandwidth Digital
Content Protection (HDCP). HDCP encrypts the transmission
between the video source and the digital display for added
security and protection.
b) Refer to your TV Set-Top Box user manual for more information
about the video output requirements of the product or consult
your cable or satellite operator.
c) The DVI to HDMI connection provides video only. Connecting an
alternate audio player to PC audio port is required for audio.
ENGLISH

19
5. Using an audio cable (red and white connectors), connect the
cable to the audio output connectors associated with the
Component output on your TV Set-Top Box and connect the
other end to the audio connectors associated with the
Component.
6. Turn on the power to the TV and TV Set-Top Box.
7. Select Component using the INPUT button on the remote, side
of the TV or directly by pressing the COMP button on the
Remote Control.
Connecting Your Basic Set-Top Box
Using Composite Video
1. Turn off the power to the TV and Set-Top Box.
2. Using an AV Cable, connect the Video (yellow color) connector
on your Set-Top Box to the corresponding Video (yellow color)
connector in the AV group at the rear of the TV.
3. Using the red and white connectors, connect the cable to the
audio output connectors associated with the Video output on
your Set-Top Box and connect the other end to the audio
connectors associated with the AV input at the rear of the TV.
4. Turn on the power to the TV and Set-Top Box.
5. Select Composite using the INPUT button on the remote, side
of the TV or directly by pressing the VIDEO button on the
Remote Control.
Note:
Refer to your TV Set-Top Box user manual for more information
about the video output requirements of the product or consult
y
our cable or satellite o
p
erato
r
.
ENGLISH