AOC L22W831 User manual

L W831

TABLE OF CONTENTS
TABLE OF CONTENTS …………………………………………….....1
FOR YOUR SAFETY ………………………………………………….. 2
PRCAUTIONS AND REMINDERS ………………………………….. 3
IMPORTANT SAFETY INSTRUCTIONS ………………………….. 5
Package Contents……………………………………………………......7
Attaching the Base ………………………………………………………7
Preparing Your LCD TV for Wall Mounting ……………………………8
PREPARATION ………………………………………………………… 9
PERIPHERAL CONNECTION GUIDE …………………………..…. 11
OPERATING INSTRUCTIONS ………………………………………. 13
TO USE THE FRONT PANEL CONTROL …………………….... 13
TO USE THE REMOTE CONTROL …………………………..…. 14
CONNECTING EQUIPMENT………………………………………16
TO USE THE MENUS ……………………………………..………. 26
Main Menu …………………………………………………...….. 26
Picture Menu …………………………………………………..... 27
Sound Menu ……………………………………………………...28
Advanced Menu ……………………………………………….... 28
PC setup Menu ……………………………………………….…. 29
Installation Menu …………………………………………………29
System Menu ……………………………………………………. 30
TIPS …………………………………………………………….… 31
PRODUCT SPECIFICATION ……………………………………….…. 32
BEFORE CALLING SERVICE ………………………………………… 33
GLOSSARY ……………………………………………………...…... 34
English

1
SYMBOL SYMBOL DEFINITION
SA 1965
DANGEROUS VOLTAGE: The lightning flash with
arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of
electrical shock to persons.
SA 1966
INSTRUCTIONS: The exclamation point within on
equilateral triangle to alert the User to the presence of
important operating and maintenance (servicing)
instruction In the literature accompanying the appliance.
Apparatus shall not be exposed to dripping or splashing and no objects filled
with liquids, Such as vases, Shall be placed on the apparatus.
Caution - Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type.

2
FOR YOUR SAFETY
Before operating the TV please read this manual thoroughly. This manual should
be retained for future reference.
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE
1. The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order
to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modification to this equipment. It is the responsibilities of
the user to correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the TV to rain or moisture.
Dangerously high voltages are present inside the TV. Do not open the cabinet.
Refer servicing to qualified personnel only.
SAFETY: Lamp Disposal
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED
OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR MORE
INFORMATION, CONTACT THE ELECTRONIC
INDUSTRIES ALLIANCE AT WWW.EIAE.ORG.

3
Place unit on even surfaces. Don't place the TV in confined spaces
or in a box when using it.
Unplug immediately if is malfunction
like no picture, no video/audio,smoke
and bad odor from TV.
Unplug immediately if other foreign
materials are put inside TV box or if
the TV fell down.
Don't throw any object inside the TV
box like metals or other flammable
materials.
Prohibit/Avoid opening TV cabinet
PRECAUTIONS AND REMINDERS

4
Remember to unplug the AC cord
from the AC outlet before cleaning. Do
not use liquid cleaners or aerosol
cleaners to clean the display.
Avoid direct sunlight, dusty, high
humidity and smoky areas.
Make sure to unplug the unit when not
in use for a long period of time (days).
Call service personnel to clean the
internal part of the TV once a year.
Do not cover or block any vents and
openings. Inadequate ventilation may
shorten the life of the display unit and
cause overheating.
Do not place the display near water,
such as bathtub, washbasin, kitchen
sink laundry tub, swimming pool or in
a damp basement.
Notice for Remote Controller
Avoid Dropping Avoid Liquids Avoid Aerosol Cleaners
123
4
56
789
0
12
3
45
6
789
0
1
23
456
789
0

5
Read before operating equipment
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with the
manufacturers instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and third grounding prong. The wide blade or third
prong is provided for your safety. When the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13. The TV should be operated only from the type of power source indicated on
the label. If you are not sure of the type of power supplied to your home,
consult your dealer or local power company.
14. Unplug this apparatus during lightning storms or when unused for long
periods of time.
15. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into apparatus,
the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
16. This product may contain lead or mercury. Disposal of these materials may
be regulated due to environmental considerations. For disposal or recycling
information, please contact your local authorities or the Electronic Industries
Alliance: www.eiae.org
17. Damage Requiring Service – The appliance should be serviced by qualified
service personnel when:
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a marked
change in performance; or
E. The appliance has been dropped, or the enclosure damaged.
IMPORTANT SAFETY INSTRUCTIONS

6
18. Tilt/Stability – All televisions must comply with recommended international
global safety standards for tilt and stability properties of its cabinets design.
Do not compromise these design standards by applying excessive pull
force to the front, or top, of the cabinet, which could ultimately overturn
the product.
Also, do not endanger yourself, or children, by placing electronic
equipment/toys on the top of the cabinet. Such items could
unsuspectingly fall from the top of the set and cause product damage
and/or personal injury.
19. Wall or Ceiling Mounting – The appliance should be mounted to a wall or
ceiling only as recommended by the manufacturer.
20. Power Lines – An outdoor antenna should be located away from power lines.
21. Outdoor Antenna Grounding – If an outside antenna is connected to the
receiver, be sure the antenna system is grounded so as to provide some
protection against voltage surges and built up static charges.
Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, provides
information with respect to proper grounding of the mats and supporting
structure grounding of the lead-in wire to an antenna-discharge unit, size of
grounding connectors, location of antenna-discharge unit, connection to
grounding electrodes and requirements for the grounding electrode. See
Figure below.
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL
CODE
Note to the CATV system installer: This reminder is provided to call the
CATV system installer’s attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close
to the point of cable entry as practical.
Please, make sure to connect the power plug to the wall outlet socket after
connecting the TV to the adapter!
22. Objects and Liquid Entry – Care should be taken so that objects do not fall
and liquids are not spilled into the enclosure through openings.

7
Package Contents
AOC L22W831 TV unit
Power cord
Remote control
Batteries (AAA) (Except Argentina)
Audio cable
signal cable
User manual
Quick Setup Guide
IMPORTANT: Do not apply pressure to the screen display area which may
compromise the integrity of the display. The manufacturer’s warranty does not
cover user abuse or improper installations.
Attaching the Base
IMPORTANT: The Base of the TV must be assembled prior to usage.
1. Place TV unit face down on a soft and flat surface (blanket, foam, cloth,
2. etc.) to prevent any damage to the TV.
3. Carefully align and insert the Base to the stand.
4. Gently push the Base towards the TV until the locking mechanism locks
into place.

8
100
mm
Preparing Your LCD TV for Wall Mounting
We suggest that you keep your TV at least 2.36 inches (60 mm) from the wall to
prevent cable interference.
Before you wall-mount your TV, you need to remove the base.
To attach a wall mount bracket to your TV:
1 Remove the two T4 and two M4 screws holding your TV to the stand.
2 Remove the three screws from the bottom of the stand.
3 Secure the wall mount bracket to the back of your TV using four M6 screws,
as indicated in the illustration.
100 mm
A
tt ach
br acket
her e
R e m o v e T 4 sc r e w s R e m o v e M 4 sc r e w s
R
em o v e st and
Note: 100mmx100mm wall mount bracket & M6 screws not included.

9
Please, make sure to connect the power plug to the wall outlet socket after
connecting the TV to the power cord!
1. Install the base stand; place the TV on a solid surface.
Ensure that the TV is placed in a position to allow free flow of air. Do not cover
the ventilation openings on the back cover.
To prevent any unsafe situations, no naked flame sources, such as lighted
candles, should be placed on or in the vicinity.
Avoid heat, direct sunlight and exposure to rain or water. The equipment shall
not be exposed to dripping or splashing.
2. Connect the antenna cable or CATV cable to the aerial socket TV IN at the
back of the TV set.
PREPARATION

10
3. Remote control:
Remove the cover of the battery compartment. Insert the 2 batteries supplied
(Type AAA 1.5V).
4. Power:
Insert the power cord in the wall socket having an AC power supply. You can
see LED states at the front panel. If the LED color is Blue, means the TV set is
power on. If the LED color is Red,which means this TV set is in standby state.
5. Turn the TV on:
Push the POWER key on the Remote control or the Front panel control knobs.
Wait a minute, the TV will power on and can see the display on the screen
POWER Key

11
HDMI S-Video Composite Pr Pb Y PC Audio in 15-pin D-Sub
1. HDMI – Connect the primary source for digital video such as a DVD
multimedia player or set top box through this all digital connector.
The white color band on the rear of the TV indicates this connection.
2. PC IN– Connect the video and audio cables from a computer here.
3. AV/S-VIDEO IN – Connect the primary source for composite video
devices, such as a VCR or video game. Use the white and red
PERIPHERAL CONNECTION GUIDE

12
connectors to connect the external audio from the same source.
The signal being carried by the S-Video cable and connector, if
connected, will take priority over the Video RCA connector (yellow
connector).
4. COMPONENT (Y Pb/Cb Pr/Cr with Audio L/R) – Connect the
primary source for component video devices such as a DVD Player
or set top box here. From left to right, use red for Pr, blue for Pb,
green for Y, red for right audio (R) and white for left audio (L) inputs.
5. TV IN– Connect to an RF cable (out-of-the-wall, not from Cable Box)
for TV.
Once your equipment is connected, use the following procedure to view the input
signal:
Press the source button on the remote controller to select the relevant source to
view. (ex: Press VIDEO button to select “Composite Rear” if you have connected
a video recorder to Composite Rear socket.)

13
TO USE THE FRONT PANEL CONTROL
1 VOL▲
VOL +: Press to increase the volume. In Menu mode,
functions as right arrow to go to a next menu or increase a
setting.
2 VOL▼
VOL - : Press to decrease the sound volume level. In Menu
mode, functions as left arrow to go to a previous menu or
decrease a setting.
3 CH ▲
CH +: Press to select the next higher Program number.
4 CH ▼
CH - : Press to select the next lower Program number.
5 MENU
Menu key: Press to open or exit the OSD menu.
6 INPUT
Source key: Press to select the input source.
7 POWER
Power key: Press to turn on / off (standby) the TV set.
OPERATION INSTRUCTIONS

14
TO USE THE REMOTE CONTROL
PREV CH
Press to display the previous
channel .
MTS/SAP
Press to activate the TV sounds,
such as: Stereo, SAP or Mono tone.
WIDE
Press to choose the display aspect
as: Normal, Zoom and Wide mode.
SOURCE
Press to display source information.
CH-/ CH +
Press to change TV channel up or
down
EXIT
Press to exit menu or OSD.
VIDEO ADJ
Press to switch the preset of video
preset mode.
AUDIO ADJ
Press to switch the preset of audio
preset mode.
CC
Press repeatedly to select closed
caption channel or set it off. You
can set as
CC1 ,CC2 ,CC3 ,CC4 ,TT1 /
TT2,TT3,TT4 and Off
FREEZE
No support for this product
FAV
No support for this product
EPG
No support for this product
V-CHIP
No support for this product
POWER
Press to power ON/OFF (standby)
TV.(Note:TV is never completely
power off unless physically
unplugged.)
VIDEO
Press to display source menu,
then move focus by ∧or ∨, and
select by ENTER.
COMP
Press to choose Component
source mode directly.
PC/HDMI
Press repeatedly to toggle
between PC and HDMI source
modes
TV
Press to select TV source mode.
0 ~ 9 number
Press to enter channel numbers
SLEEP
Press to set sleep timer,setting a
mount of time before your TV turn
off automaticlly.(you can set as
5min /10min /15min /30min/
45min/ 60min/ 90min/ 120min/
180min /240min or Off)
VOL- / VOL+
Press + or - to adjust the volume
MENU
Press to open or exit menu.
“”,“”,“＜”,“＞”,
“ENTER”
Press to adjust the various
function items on the menu.
DISPLAY
Press to show the information
about the input source or TV
channel.
MUTE
Press to mute the sound.Press
again to restore sound.

15
Viewing Modes illustrations
Normal Mode on 16:10 Display screen
The original content would be at the center of the
screen. mall black bars are ded on the left and right
side.
Wide Mode on 16:10 Display screen
The original content would fill the width of the
screen while the proper ratio of 16:9 content is still
maintained. Little cropping of the content
on the sides is necessary.。
ZOOM Mode on 16:10 Display screen
For those wide format images which are originally
programmed into 4:3 frames with top and bottom
black bars, this mode has to stretch the image in both
wide and high directions to the full display with active
data. Little cropping on sides is necessary for full
display.

16
Connecting Equipment
Coaxial (RF)
Using Your Antenna or Cable for TV
1. Turn off the power to the TV.
2. Connect the coaxial (RF) connector from your antenna or cable
(out-of-the-wall, not from the Cable Box) to the TV IN connector at
the rear of the TV
3. Turn on the power to the TV.
4. Select TV using the INPUT button on the remote, side of the TV or
directly by pressing the TV button on the Remote Control.
Using the Antenna or Cable for your VCR
1. Turn off the power to the TV and VCR.
2. Connect the “Output to TV”, “RF Out” or “Antenna Out” connector
on the rear of your VCR to the TV IN connector at the rear of the TV.
3. Turn on the power to the TV and VCR.
4. Select TV using the INPUT button on the remote, side of the TV or
directly by pressing the TV button on the Remote Control.

17
Connecting Your TV Set-Top Box
Using HDMI
TV Set-Top Boxes that have a HDMI digital interface should be connected to the
HDMI input of the LCD TV for optimal results.
Connecting your TV Set-Top Box (Best)
1. Turn off the power to the TV and TV Set-Top Box.
2. Connect a HDMI cable to the HDMI output of your TV Set-Top Box
and the other end to the HDMI Input at the rear of the TV.
3. Turn on the power to the TV and TV Set-Top Box.
4. Select HDMI using the INPUT button on the remote, side of the TV,
or directly by pressing the PC/HDMI button on the Remote Control.
Note: If you have an off-air antenna or cable TV, connect it to
the “Antenna In” connector on the rear of
y
our VCR.
Note:
a) The HDMI input on the TV supports High-bandwidth Digital
Content Protection (HDCP). HDCP encrypts the transmission
between the video source and the digital display for added
security and protection.
b) Refer to your TV Set-Top Box user manual for more information
about the video output requirements of the product or consult
your cable or satellite operator.

18
For TV Set-Top Boxes with DVI
1. Turn off the power to the TV and TV Set-Top Box.
2. Using a HDMI-DVI cable, connect the DVI end to your TV Set-Top
Box and the HDMI end to the HDMI Input at the rear of the TV.
3. Turn on the power to the TV and TV Set-Top Box.
4. Select HDMI using the INPUT button on the remote, side of the TV,
or directly by pressing the PC/HDMI button on the Remote Control.
Using Component Video
Connecting your TV Set-Top Box (Better):
1. Turn off the power to the TV and TV Set-Top Box.
2. Connect the Pr (red color) connector on your TV Set-Top Box to the
corresponding Pr (red color) connector in the Component group.
3. Connect the Pb (blue color) connector on your TV Set-Top Box to
the corresponding Pb (blue color) connector in the Component
group.
4. Connect the Y (green color) connector on your TV Set-Top Box to
the corresponding Y (green color) connector in the Component
group.
Note:
a) The HDMI input on the TV supports High-bandwidth Digital Content
Protection (HDCP). HDCP encrypts the transmission between the
video source and the digital display for added security and protection.
b) Refer to your TV Set-Top Box user manual for more information about
the video output requirements of the product or consult your cable or
satellite operator.
c) The DVI to HDMI connection provides video only. Connecting an
alternate audio player to PC audio port is required for audio.