AOC L26W861 User manual

26”LCDTV AOCL26W861
1
Service
Service
Service
Horizontal Frequency
31~60kHz
TABLE OF CONTENTS
Description Page Description Page
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
6.1.Main Board…………..…………...……….......27
6.2.Power Board……………..………….………...29
6.3.Key Board………………………..……….......30
6.4.IR Board…………………………..……….......30
7. White-Balance, Luminance Adjustment............31
8. Block Diagram.……..........................................33
9. Schematic……………...…………..…………...35
9.1.Main Board……………………………...….......35
9.2.Power Board…………………...………….......48
9.3.Key Board……………….….………….......49
10. Exploded View…………………………….…...50
11. BOM List……………….……………………….51
12.Different Parts List……………………………...69
Table Of Contents.......……..............................…........1
Important Safety Notice.......................................……......2
Revision List…………………………………………………3
1. General Specification..............................………........4
2. Operating Instructions…………………….……….......5
2.1. The Use Of Remote Control…….………….…….......5
2.2. To Use The Menu…...…………………….……….......6
2.3. How To Connect…….…………………….……….....14
2.4. Front Panel Control Knobs……………….……….....16
3. Input/Output Specification…………....................…....17
4. Mechanical Instructions…………………….................19
5. Repair Flow Chart ……………………….…….…….....22
6. PCB Layout ………………..………………....….......27

26”LCDTV AOCL26W861
2
Revision List
Version Release Date Revision Instructions TPV Model
A00 Jul.-15-2008 Initial Release E268MZNKW8AENN
A01 Sep.-17-2008 Add New BOM E268MZNKW8A52N
A02 Sep.-28-2008 Add New BOM E268MZNSW8AENN
A03 Nov.-28-2008 Add New BOM E26RMZNKW8A52N

26”LCDTV AOCL26W861
3
Important Safety Notice
Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The service
procedures recommended by AOC and described in this service manual are effective methods of performing service
operations. Some of these service operations require the use of tools specially designed for the purpose. The
special tools should be used when and as recommended.
It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in
order to minimize the risk of personal injury to service personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. AOC could not possibly know, evaluate and advise the service trade of all conceivable ways in
which service might be done or of the possible hazardous consequences of each way. Consequently, AOC has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not
recommended by AOC must first satisfy himself thoroughly that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, AOC Company will be referred to as AOC.
WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics might create
shock, fire, or other hazards.
Under no circumstances should the original design be modified or altered without written permission from AOC.
AOC assumes no liability, express or implied, arising out of any unauthorized modification of design.
Servicer assumes all liability.
FOR PRODUCTS CONTAINING LASER:
DANGER-Invisible laser radiations when open AVOID DIRECT EXPOSURE TO BEAM.
CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION -The use of optical instruments with this product will increase eye hazard.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF
THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment person’s body is grounded through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may
damage the panel.)

26”LCDTV AOCL26W861
4
1. General Specification
Items Specification
Panel Type V260B1-L11 26" CMO TW
Driving system TFT-LCD CMO Panel
Active Area 575.769(H) x 323.712(V)
Resolutions 1366 x768
Brightness 500 cd/㎡
Contrast 800:1
Pixel Pitch 0.1405mm x0.4215mm
Display colors 16.2 million
LCD Panel
Color Temperature Cool / Warm/normal
Television System TV Standard NTSC standard
ATSC standard (8-VSB, Clear-QAM)
AV RCA x 1
S-Video S-Video x 1 Audio L/R x 1
COMPONENT Y,Cb,Cr x 1 Audio channel L / Rx 1
HDMI 720p,1080i,480p,480i
Video Inputs
PC VGA x 1 PC Audio in x 1
Speaker (built-in): Two 5W speakers
Audio Output Audio Output: L / R SPDIF
OSD language English, etc
Wall Mount VESA 200 mm x 100 mm
Dimensions 651.9mm(W) x 480.0mm(H) x 219.7mm(L)
Weight 9kg(With Stand)
Power Supply AC100V~240V, 50/60Hz
< 120W
Power Power Consumption 1 W in standby mode (power cord plugged in and
power OFF)
Operating 5 °C ~ 40 °C
Storage 0 °C ~ 50 °C
Environment
Operating 10% ~ 85%

26”LCDTV AOCL26W861
5
2. Operating Instructions
2.1 The Use of Remote Control
PREV CH
Press to display the previous TV .
MTS/SAP
Press to activate the NTSC TV
sounds, such as: Stereo, SAP or
Mono tone. And languages of DTV.
WIDE
Press to choose the display aspect
as: Normal, Wide, Zoom or Cinema
mode.
SOURCE
Press repeatedly to choose the
various input sources (Video 1 ~ 6).
EPG
This function is not support.
MUTE
Press to set TV sound mute ON/OFF
DISPLAY
Press to show the information about
the input source、TV channel、display
resolution and current time.
VOL- / VOL+
Press + or - to adjust the volume.
Exit
Press to exit menu or OSD.
V-CHIP
Press to lock / unlock Parental
Control temporarily. (After setting the
restricted table of MPAA or TV
Rating.)
VIDEO ADJ
Press to choose the Brightness or
Contrast adjustment.
AUDIO ADJ
Press to switch the ATSC
multi-channel TV sounds.
CC
Press repeatedly to change the
closed caption type as CC ON/CC
OFF/CC ON WHEN MUTE.
FAVORITE
Press to toggle the Favorite/Normal
mode.
POWER
Press to power ON/OFF (standby)
TV. (Note:1.TV is never completely
power off.
unless physically unplugged.
2.Press to turn on TV after the power
on status LED had changed to the
red color and stopped flashing. )
VIDEO
Press repeatedly to choose S-Video/
Composite source mode (Video 1 ~ 2).
COMP
Press repeatedly to choose
Component
source mode (Video 3 ).
PC/HDMI
Press repeatedly to choose VGA or
HDMI source mode (Video 4 ~ 6).
TV
Press to choose ATSC/NTSC TV
source mode.
0 ~ 9 /- number
Press to enter TV channel number to
select channel (Press ‘-’ to indicate
choosing the sub-channel).
SLEEP
Press to set a time period
(off/30min/60min/90min) after which
the TV should switch itself to standby
mode.
FREEZE
Press to freeze the displayed picture
VOL- / VOL+
Press + or - to adjust the volume.
MENU
Press to open or exit menu.
“∧”,“∨”,“＜”,“＞”, “ENTER”
Press to adjust the various function
items on the menu.

26”LCDTV AOCL26W861
6
MAIN MENU
2.2 To Use the Menus
1 Press the MENU button.
2 Press the or button repeatedly to select a menu item.▽△
3 Press the < or > buttons to enter a sub-menu.
4 Press the ENTER or > button to confirm an adjustment or toggle a setting.
5 Press MENU or EXIT to close the on-screen menu.
On-screen menus
On-screen menu Options
Setup
Tuning Band–Selects the TV antenna source (Air or Cable).
DTV Signal–Displays the digital TV signal strength. For more information.
Auto Ch Search–Automatically sets up a list of the channels available in your
area.
Add On Ch Search–Lets you add new channels without going through the
entire list of available channels.
Manual Ch Set–Lets you add or delete channels from the channel list.
Channel Labels–Lets you add a label to a channel. For more information.
Menu Language–Selects the language for the on-screen menu. You can
select English, French, or Spanish.
Aspect Ratio–Selects the screen aspect ratio:
Normal, Wide1, Wide2, Zoom, or Cinema. You can also press ZOOM to
select the aspect ratio.
Favorite Channel mode–Lets you edit your favorite channel list. Press
FAVORITE on the remote to toggle this mode on or off.
Video
(Options may vary in different
modes.)
Contrast–Increases the picture level to adjust the white areas of the picture.
Decreases the picture level to adjust the black areas of the picture. (0 ~ 100)
Brightness–Increases the brightness to add more light to dark areas of the
picture. Decreases the brightness to add more dark to light areas of the
picture. (0 ~ 100)
Sharpness–Increases the sharpness for a cleaner and clearer image.
Decreases the sharpness for a smoother picture. (-50 ~ 50)

26”LCDTV AOCL26W861
7
Color–Adjusts the overall color of the picture. (0 ~ 100)
Tint–Increases the color level to add more green to skin tones. Decreases the
color level to add more purple to skin tones. (R50 ~ G50)
Backlight–Adjusts the backlight level (0 ~ 10).
Settings–Restores the video settings to factory default.
Audio
(Options may vary in different
modes.)
Audio Language–Selects an alternate language if the program has more
than one language available. Only available in ATSC TV mode.
Bass–Adjusts the low sounds (bass).
Treble–Adjusts the high sounds (treble).
Balance–Adjusts the right and left speaker volumes.
Digital Audio Output–Selects the audio mode for the digital audio optical
jack.
• RAW: AC-3 in - AC-3 out/PCM in – PCM out.
• PCM: AC-3 in - PCM out/PCM in – PCM out.
TV Speaker–Turns the internal TV speaker On (default) or Off. Does not
affect the digital audio output, the headphone output, and the composite audio
output.
Settings–Restores the audio settings to factory default.
Feature
Time Set–Sets the clock. For more information
Sleep Timer–Sets the sleep timer.
Advanced Video Set–
• Noise Reduction–Select from Low, Mid, High, and Off.
• Color Temperature–Select from Normal, Warm, and Cool (default).
• 3D Y/C–Choose from On (default) or Off.
• Dynamic Contrast–Choose from On or Off (default).
• Setting–Restores the settings to factory default.
Password Set–Lets you set the password for parental control options. The
default password is 0000.
Parental Control–Accesses V-chip controls.
Digital Caption–Sets the digital caption type. Choose from Service 1-6, Text
1-4, and CC 1-4.
Digital Close Caption:–Customizes closed captions for digital broadcasting
systems. You can adjust Size, Font, Text Color, Text Opacity,
Background Color, Background Opacity, Edge Effect, and Edge Color.
Component Set–Only available in component mode. Lets you set Horizontal
Position (1 ~ 100), Vertical Position (1 ~ 100), and Phase (1 ~ 100). The
Settings option restores the settings to factory default.
VGA Set–Only available in VGA mode. Lets you set Horizontal Position (1 ~
100), Vertical Position (1 ~ 100), Clock (1 ~ 100), and Phase (1 ~ 100). You
can also select Auto Adjust to automatically adjust the settings. The Settings
option restores the settings to factory default.

26”LCDTV AOCL26W861
8
USING YOUR TV
To turn your TV on and off:
1 Make sure that the power cord is connected to your TV and a power outlet.
2 Press the POWER button to turn on your TV. The power indicator LED turns blue.
3 Press the POWER button again to return your TV to standby. The power indicator LED turns red.
To select the TV signal source:
• With the TV on, press the INPUT button on either the TV or the remote to choose from:
• TV
• Composite
• S-Video
• Component
• VGA
• HDMI
Setting up the channel list:
After you select your TV source, if you selected antenna or cable you need to set up the channel list. When you set
up your channel list, your TV searches for all available channels in your area and store a list of these channels.
When you press the CH ＾or CH v buttons, your TV skips the channels that do not have a signal.
To automatically set up the channel list:
1 Press the MENU button. The Main on-screen display menu opens with Setup highlighted.
2 Press the > button to enter the sub-menu, then or▽button to highlight△Auto Ch Search.
3 Press ENTER or >to start the search.
Manually adding or deleting channels from the channel list
After you create a channel list using the Auto Ch Search option, you can manually add or delete channels from the
channel list.
To add or delete channels:
1 Press the MENU button. The Main OSD (On-Screen Display) menu opens with Setup highlighted.
2 Press the > button to enter the sub-menu, then or to highlight▽△ Manual Channel Set. The Channel Setup
Table opens.
3 Press the or button to select a channel, then press then press▽△ ENTER to toggle between viewable and not
viewable.
4 Press MENU or EXIT to close the menu.
To change channels:
• Press the CH v or CH ^ button on the remote control to go to the next lower or higher channel. Or Press the
number buttons to directly select a channel (for example, if you want channel 83, press 8, then press 3).Or Press the
RECALL button to go to the last viewed channel.
Selecting a digital sub-channel
Most digital TV channels have more than one channel. The main channel carries the signal for the main TV program.
The sub-channels carry signals for additional or alternate programming, such as a radio or news broadcast.

26”LCDTV AOCL26W861
9
For example, if the main channel number is 8, the sub-channel number might be 8-1, 8-2, or 8-3.
To select a sub-channel:
1 Press the number buttons for the main channel (for example 8).
2 Press the – button, and then press the sub-channel button (for example 1).
To adjust the volume:
• Press the VOL – or VOL + button to decrease or increase the volume.
• Press the MUTE button to turn off the sound. Press the MUTE button again to turn the sound back on.
To display status information:
• Press the DISPLAY button. Your TV displays status information, such as the channel number or signal source.
To check the DTV signal strength:
1 Press the MENU button. The Main OSD (On-Screen Display) menu opens with Setup highlighted.
2 Press the > button to enter the sub-menu, then or to highlight▽△ DTV Signal. The DTV Signal meter opens.
3 Press MENU or EXIT to close the menu.
To add a label to a channel:
1 Press the MENU button. The Main OSD (On-Screen Display) menu opens with Setup highlighted.
2 Press the > button to enter the sub-menu, then or to highlight▽△ Channel Labels. The Channel Label menu
opens.
3 Press the < or > button to move the cursor to the channel field or label field, and then press the or button to▽△
select
4 Press < or > to move the cursor to the label field, then press or to select the character.▽△
5 Press the ENTER key to return to the previous menu.
Freezing the picture
You can freeze (still) the screen image.
To freeze or unfreeze the picture:
• Press the FREEZE button.
To set the clock:
1 Press the MENU button. The Main OSD (On-Screen Display) menu opens with Setup highlighted.
2 Press the or button repeatedly to highlight▽△ Feature. The Feature menu opens.

26”LCDTV AOCL26W861
10
3 Press the > button to enter the sub-menu, then or to highlight▽△ Time Set. The Time Set menu opens.
4 Press the or button move to the different fields, then press < or >to c▽△ hange the settings.
5 Press MENU or EXIT button to close the menu.
To set the sleep timer:
1 Press the MENU button. The Main OSD (On-Screen Display) menu opens with Setup highlighted.
2 Press the or button repeatedly to highlight▽△ Feature. The Feature menu opens.
3 Press the > button to enter the sub-menu, then or to highlight▽△ Sleep Timer.
4 Press < or > to select the amount of time (Off, 5 min, 10 min, 15 min, 30 min, 45 min,60 min, 90 min, 120 min,
180 min, 240 min). To turn off the timer, select off.
To view closed captions:
• Press the CCD button repeatedly to select a closed caption option. You can select:
• On
• Off
• On When Mute
Setting parental controls
Your TV has a V-chip that lets you control the type of programs your children can watch. Parental controls include
two ratings: MPAA (based on age) and TV Parental Guidelines (based on content and age). A TV program may
have an MPAA or TV Parental Guidelines rating, so you should set controls for both ratings. Before you can select
ratings, you need to set up a parental controls password.

26”LCDTV AOCL26W861
11
To set up a password:
1 Press the MENU button. The Main OSD (On-Screen Display) menu opens with Setup highlighted.
2 Press the or button repeatedly to highlight▽△ Feature. The Feature menu opens.
3 Press the > button to enter the sub-menu, then or to highlight▽△ Password Set.
4 Press the number buttons to enter the old password. If you have not set a password, enter 0000. Press ENTER to
continue.
5 Press the number buttons to enter a new password. Press ENTER to continue.
6 Press the number buttons to enter the new password again, to confirm. Press ENTER to continue.
To set the Parental Control level:
1 Press the MENU button. The Main OSD (On-Screen Display) menu opens with Setup highlighted.
2 Press the or button repeatedly to highlight▽△ Feature. The Feature menu opens.
3 Press the > button to enter the sub-menu, then or to highlight▽△ Parental Control. The Password screen
opens.
4 Press the number buttons to enter the password. Press ENTER to continue. The Parental Control Menu opens.
5 Press the or button to select▽△ USA Parental Locks or Canadian Parental Locks, the press ENTER. The
Controls Menu that you have selected opens.

26”LCDTV AOCL26W861
12
6 Press < or >, or or to move to a rating,▽△ and then press ENTER to select the rating. When you block a rating,
that rating and all higher ratings are blocked.
7 Press MENU or EXIT button to close the menu.
American MPAA ratings
Canadian MPAA Ratings

26”LCDTV AOCL26W861
13
TV Parental Guidelines ratings
Some of the age-based TV Parental Guidelines ratings also have content-based ratings.

26”LCDTV AOCL26W861
14
2.3 How to Connect

26”LCDTV AOCL26W861
15
1. HDMI – Connect the primary source for digital video such as a DVD multimedia player or set top box through
this all digital connector. The white color band on the rear of the TV indicates this connection.
2. RGB PC – Connect the video and audio cables from a computer here.
3. AV/S-VIDEO IN – Connect the primary source for composite video devices, such as a VCR or video game.
Use the white and red connectors to connect the external audio from the same source. The signal being
carried by the S-Video cable and connector, if connected, will take priority over the Video RCA connector (yellow
connector).
4. COMPONENT (YPb/CbPr/Cr with Audio L/R) – Connect the primary source for component video devices such
as a DVD Player or set top box here. From left to right, use red for Pr, blue for Pb, green for Y, red for right
audio (R) and white for left audio (L) inputs.
5. DTV – Connect to an antenna or digital cable (out-of-the-wall, not from Cable Box) for Digital TV.*
6. SPDIF (Optical Digital Audio Out) - When a digital audio signal is associated with the input selected for
viewing, the digital audio will be available on this SPDIF connection to your home theater system.
Once your equipment is connected, use the following procedure to view the input signal:
Press the source button on the remote controller to select the relevant source to view. (Ex: Press VIDEO
button to select “Composite Rear” if you have connected a video recorder to Composite Rear socket.)

26”LCDTV AOCL26W861
16
2.4 Front Panel Control Knobs
1 VOL + VOL +: Press to increase the sound volume level.
2 VOL - VOL - : Press to decrease the sound volume level.
3 CH ▲CH +: Press to select the next higher Program number.
4 CH ▼CH - : Press to select the next lower Program number.
5 MENU Menu key: Press to open or exit the OSD menu.
6 INPUT Source key: Press to select the input source.
7 POWER
Power key: Press to turn on / off (standby) the TV set.
(Please re-turn on TV after the Power-ON status LED had changed to
the Red color and finished flashing.)

26”LCDTV AOCL26W861
17
3. Input/Output Specification
3.1 RGB Signal input
15 - Pin Color Display Signal Cable
Pin No. Description Pin No. Description
1 Red Video 9 Mandatory +5V Supply for PC Bypass
2 Green Video 10 Sync Ground
3 Blue Video 11 SDA(Remote Control)
4 SCL(Remote Control) 12 Bi-directional Data (SDA) for PC Bypass
5 Ground 13 H-Sync.
6 Red Video Ground 14 V-Sync.
7 Green Video Ground 15 Data Clock (SCL) for PC Bypass
8 Blue Video Ground
3.2 HDMI Digital connector pin assignments
Pin No. Description Pin No. Description
1 TMDS Data2+ 2 TMDS Data2 Shield
3 TMDS Data2- 4 TMDS Data1+
5 TMDS Data1 Shield 6 TMDS Data1-
7 TMDS Data0+ 8 TMDS Data0 Shield
9 TMDS Data0- 10 TMDS Clock+
11 TMDS Clock Shield 12 TMDS Clock-
13 CEC 14 NC
15 SCL 16 SDA
17 DDC/CEC Ground 18 +5V Power
19 Hot Plug Detect
1
6
11 15
5
10

26”LCDTV AOCL26W861
18
3.3 AV/S-Video/Component Video Inputs
3.4 Compatible Mode Table
VESA MODES
Horizontal Vertical
Mode Resolution Total
Nominal
Frequency
(KHz)
Sync
Polarity
Nominal
Freq.
(Hz)
Sync
Polarity
Nominal
Pixel
Clock
(MHz)
640x480@60Hz 800 x 525 31.469 N 59.940 N 25.175
640x480@72Hz 832 x 520 37.861 N 72.809 N 31.500
640x480@75Hz 840 x 500 37.5 N 75 N 31.500
VGA
720x400@70Hz 900 x 449 31.469 N 70.087 P 28.322
800x600@56Hz 1024 x 625 35.156 P 56.25 P 36.000
800x600@60Hz 1056 x 628 37.879 P 60.317 P 40.000
800x600@72Hz 1040 x 666 48.097 P 72.188 P 40.000
SVGA
800x600@75Hz 1056 x 625 46.875 P 75 P 49.5
1024x768@60Hz 1344x806 48.363 N 60.004 N 65.000
1024x768@70Hz 1328x806 56.476 N 70.069 N 75.000
XGA
1024x768@75Hz 1312x800 60.023 P 75.029 P 78.750
WXGA 1360x768@60Hz 1792X795 47,712 P 60.015 P 85.5
AV (Composite Video input)
Video1
System NTSC
Amplitude 1.0 V (p-p), negative sync.
Impedance 75 ohm terminated
S-Video (Y / C input)
S-Video2
System NTSC
Y signal amplitude 1.0Vpp (including sync)
C signal amplitude 0.286Vpp
Impedance 75 ohm terminated
Component (Y, Pb/Cb, Pr/Cr input)
Video3
System 1080i, 480p, 720p, 480i
Y signal amplitude 1.0Vpp (including sync)
Cr, (R-Y) / Cb, (B-Y)
Signal amplitude ±0.35Vpp, 75 ohm
Impedance 75 ohm terminated

26”LCDTV AOCL26W861
19
4. Mechanical Instructions
1. Remove the 3 screws to remove the base.
2. Remove 11 screws to remove the rear cover.
3.RemovethescrewstoremovetheBKT-vesa.

26”LCDTV AOCL26W861
20
4. Release the connectors.
5. Remove the speakers.
6. Remove the main board, power board