AOC LM565 User manual

AOC LM565
1
15” LCD MONITOR
LM565
THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY REASONABLE EFFORT
HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE
ACCURACY OF THIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS RE LIABILITY FOR
CHANGES, ERRORS OR OMISSIONS.
SERVICE MANUAL
http://www.wjel.net

AOC LM565
2
Table of Content
Revision List…………………………………………………………………………………………………………. 3
1. Monitor Specifications………………………………………………………………………………………….. 4
2. LCD Monitor Description……………………………………………………………………………………….. 5
3. Operating Instructions………………………………………………………………………………………….. 6
3.1 General Instructions…………………………………………………………………………………………... 6
3.2 Front Panel Control…………………………………………………………………………………….……... 6
3.3 Adjusting the Picture………………………………………………………………………………………….. 7
4. Input/Output Specification……………………………………………………………………………………... 9
4.1 Input Signal Connector……………………………………………………………………………………….. 9
4.2 Power Supply Requirements………………………………………………………………………………… 9
4.3 Factory Preset Display Modes……………………………………………………………………………….. 10
4.4 Panel Specification………………………………………………………………………………………….… 11
4.4.1 Panel Feature……………………………………………………………………………….……………. 11
4.4.2 Display Characteristics……………………………………………………………….………………….. 11
4.4.3 Optical Characteristics…………………………………………………………………………………… 12
4.4.4 Electrical Characteristics………………………………………………………………………………… 13
5. Block Diagram………………………………………………………………………………………………….… 14
5.1 Monitor Explored View………………………………………………………………………………………... 14
5.2 Software Flow Chart…………………………………………………………………………………………... 15
5.3 Electrical Block Diagram……………………………………………………………………………………… 17
5.3.1 Main Board……………………………………………………………………………………………….. 17
5.3.2 Inverter/Power Board……………………………………………………………………………………. 18
6. Schematic……………………………………………………………………………………………………….… 19
6.1 Main Board…………………………………………………………………………………………………….. 19
6.2 Power Board……………………………………………………………………………………….………….. 25
6.3 Audio Board……………………………………………………………………………………….…………… 27
7. PCB Layout……………………………………………………………………………………………………….. 28
7.1 Main Board…………………………………………………………………………………………………….. 28
7.2 Power Board………………………………………………………………………….……………………….. 29
7.3 Audio Board………………………………………………………………………….………………………… 30
7.4 Keypad Board…………………………………………………………………………………………………. 30
8. Maintainability……………………………………………………………………………………………………. 31
8.1 Equipments and Tools Requirement………………………………………………………………………… 31
8.2 Trouble Shooting…………………………………………………………………………………………….… 32
8.2.1 Main Board………………………………………………………………………………………………... 32
8.2.2 Power /Inverter/Board…………………………………………………………………………………… 35
8.2.3 Keypad Board…………………………………………………………………………………………….. 37
9. White-Balance, Luminance adjustment………………………………………………………………….….. 38
10. EDID Content……………………………………………………………………………………………………. 39
11. BOM List ………………………………………………………………………………………………………... 40
12. Different Parts List……………………………………………………………………………………………... 51
http://www.wjel.net

AOC LM565
4
1. Monitor Specifications
Items Description
Driving system TFT Color LCD
Type SVA150XG04TB
Size 38cm (15.0")
Pixel pitch 0.297mm (H) x 0.297mm (V)
Viewable angle 120(H) 100(V)
LCD Panel
Response time 16 ms
Sync. Type H/V TTL
Input Signal 15Pin Analog
H-Frequency 30kHz – 60kHz
Input
V-Frequency 55-75Hz
ON Mode <25W
Power Consumption
OFF Mode <2W
Display Color 16,777,216 colors (6bit+FRC)
Contrast Ratio 450:1
Dot Clock 80MHz
White Luminance 250cd/m2
Max. Resolution 1024 x 768
Plug & Play VESA DDC2BTM
Power Source 100~240VAC,47~63Hz
Maximum Screen Size Horizontal : 304.1mm
Vertical: 228.1mm
Environmental
Conditions
Operating Temp: 5°C to 35°C
Storage Temp: -20°C to 60°C
Operating Humidity: 10% to 85%
http://www.wjel.net

AOC LM565
5
2. LCD Monitor Description
The LCD MONITOR will contain a main board, a power board, a keypad board and an audio board which house the
flat panel control logic, brightness control logic and DDC.
The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips
each voltage.
Video signal, DDC
CCFT Drive.
PWPC Board
(
Include Ada
p
ter and Inverter
)
Flat Panel and
CCFL backlight
Main Board
RS232 Connector
For white balance
adjustment in factory
mode
HOST Computer
AC-IN
100V-240V
Monitor Block Diagram
Audio board Keyboard
http://www.wjel.net

AOC LM565
6
3. Operating Instructions
3.1 General Instructions
Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the
monitor. By changing these settings, the picture can be adjusted to your personal preferences.
•The power cord should be connected.
•Connect the video cable from the monitor to the video card.
•Press the power button to turn on the monitor position. The power indicator will light up.
3.2 Front Panel Control
-Power Button:
When pressed, the monitor enters the off mode, and the LED turns blank. Press again to restore normal status.
-Left / Right Button:
The Left/Right Button is used to control the monitor functions. Press to switch functions or adjust settings.
- Auto Adjust Key:
The Auto Adjust Key is used to automatically set the H Position, V Position, Clock and Phase.
AUTO VOL- POWER VOL+ MENU
NO. Name Within OSD Without OSD
1 AUTO Exit OSD or back to previous menu Auto configuration
2 VOL- / 1.Move the cursor to left
2.Decrease the value of the selected item Activate the audio menu
3 Power Power On / Off Power On / Off
4 VOL+ / 1.Move the cursor to right
2.Increase the value of the selected item
Activate the audio menu
5 MENU Select Function or select Sub menu Activate OSD main menu
http://www.wjel.net

AOC LM565
7
3.3 Adjusting The Picture
The Description For Control Function:
Main Menu
Item
Main
Menu
Icon
Sub Menu
Item
Sub Menu
Icon Description Adjust
Range Reset Value
Contrast
Contrast from Digital-register. 0-100 Recall Cool
Contrast Value
Luminance
Brightness
Backlight Adjustment 0-100 Recall Cool
Brightness Value
Focus
Adjust Picture Phase to reduce
Horizontal-Line noise 0-100 Do Auto Config
Image Setup
Clock
Adjust picture Clock to reduce
Vertical-Line noise. 0-100 Do Auto Config
H. Position
Adjust the horizontal position of the
picture. 0-100 Do Auto Config
Image
Position V. Position
Adjust the vertical position of the
picture. 0-100 Do Auto Config
C1 N/A
Recall warm Color Temperature
from EEPROM. N/A
C2 N/A
Recall cool Color Temperature from
EEPROM. N/A
User / Red
Red Gain from Digital-register. 0-100
User /
Green
Green Gain from Digital-register. 0-100
Color Temp.
User / Blue
Blue Gain from Digital-register. 0-100
The Color
Temperature will
be set to Cool.
The User R/G/B
value (default is
100) will not be
Modified by Reset
function.
Yes N/A
A
uto Adjust the H/V Position, Focus
and Clock of picture. N/A N/A
Auto Config
(Analog-Only
Model) No N/A
Do not execute Auto Config, return
to main menu. N/A N/A
http://www.wjel.net

AOC LM565
8
H. Position
Adjust the horizontal position of the
OSD. 0-100 50
V. Position
Adjust the vertical position of the
OSD. 0-100 50
OSD Setup
OSD
Timeout
Adjust the OSD timeout. 10-120 10
English N/A Set OSD display language to
English. N/A
Deutsch N/A Set OSD display language to
German. N/A
Français N/A Set OSD display language to
French. N/A
Español N/A Set OSD display language to Spain. N/A
Italiano N/A Set OSD display language to Italian. N/A
Language
简体中文 N/A Set OSD display language to
simplified Chinese. N/A
The Language
will be set to
English.
Information
Information N/A
Show the resolution, H/V frequency
and input port of current input
timing.
N/A N/A
Yes N/A
Clear each old status of
Auto-configuration and set the color
temperature to Cool.
N/A N/A
Reset
No N/A
Do not execute reset, return to main
menu. N/A N/A
Exit
N/A N/A Exit OSD N/A N/A
http://www.wjel.net

AOC LM565
9
4. Input/Output Specification
4.1 Input Signal Connector
Pin No. Description Pin No. Description
1. Red 9. +5V
2. Green 10. Logic Ground
3. Blue 11. RS-232RX
4. RS232-TX 12. DDC-Serial Data
5. Ground 13. H-Sync
6. R-Ground 14. V-Sync
7. G-Ground 15. DDC-Serial Clock
8. B-Ground
VGA connector layout
15
610
11 15
4.2 Power Supply Requirement
A/C Line voltage range : 100 V ~ 240 V
A/C Line frequency range : 50 ±3Hz, 60 ±3Hz
Input Current : 0.6A max. at 100V , 0.35A max. at 240 V <0.3A
Peak surge current : < 55A peak at 240 VAC and cold starting
Leakage current : < 3.5mA
Power line surge : No advance effects (no loss of information or defect)
with a maximum of 1 half-wave missing per second
Voltage : 12VDC ± 5%
CURRENT : 3.5 Amp (max)
http://www.wjel.net

AOC LM565
10
4.3 Factory Preset Display Modes
VESA MODES
Horizontal Vertical
Mode Resolution Total
Nominal
Frequency
+/- 0.5kHz
Sync
Polarity
Nominal
Freq.
+/- 1 Hz
Sync
Polarity
Nominal
Pixel
Clock
(MHz)
640x480@60Hz 800 x 525 31.469 N 59.940 N 25.175
640x480@72Hz 832 x 520 37.861 N 72.809 N 31.500
VGA
640x480@75Hz 840 x 500 37.500 N 75.00 N 31.500
800x600@56Hz 1024 x 625 35.156 N/P 56.250 N/P 36.000
800x600@60Hz 1056 x 628 37.879 P 60.317 P 40.000
800x600@72Hz 1040 x 666 48.077 P 72.188 P 50.000
SVGA
800x600@75Hz 1056x625 46.875 P 75.000 P 49.500
1024x768@60Hz 1344x806 48.363 N 60.004 N 65.000
1024x768@70Hz 1328x806 56.476 N 70.069 N 75.000
XGA
1024x768@75Hz 1312x800 60.023 P 75.029 P 78.750
IBM MODES
Horizontal Vertical
Mode Resolution Total
Nominal
Frequency
+/- 0.5kHz
Sync
Polarity
Nominal
Freq.
+/- 1 Hz
Sync
Polarity
Nominal
Pixel
Clock
(MHz)
DOS 720x400@70Hz 900 x 449 31.469 N/P 70.087 N/P 28.322
DOS 640x350@70Hz 800 x 449 31.469 P 70.087 N 25.175
XGA 1024x768@72Hz 1304x798 57.515 P 72.100 P 75.000
MAC MODES
VGA 640x480@67Hz 864x525 35.000 N 66.667 N 30.240
SVGA 832x624@75Hz 1152x667 49.725 N 74.551 N 57.2832
SGA 1024x768@75Hz 1328x804 60.241 N 74.927 N 80.000
http://www.wjel.net

AOC LM565
11
4.4 Panel Specification
4.4.1 Panel Feature
• a-Si TFT active matrix
• LVDS interface (8 bit)
• Selectable LVDS input map
• Wide viewing angle
• high response time : 16ms
• PSWG standard
• High contrast: 450:1
• Edge light type backlight (Inverter less)
• Replaceable lamp for backlight
4.4.2 Display Characteristics
http://www.wjel.net

AOC LM565
16
REMARK:
1) MCU initialize.
2) Is the EEprom blank?
3) Program the EEprom by default values.
4) Get the PWM value of brightness from EEprom.
5) Is the power key pressed?
6) Clear all global flags.
7) Are the AUTO and SELECT keys pressed?
8) Enter factory mode.
9) Save the power key status into EEprom.
Turn on the LED and set it to green color.
Scalar initialize.
10) In standby mode?
11) Update the lifetime of back light.
12) Check the analog port, are they’re any signals coming?
13) Does the scalar send out an interrupt request?
14) Wake up the scalar.
15) Are there any signals coming from analog port?
16) Display "No connection Check Signal Cable" message. And go into standby mode after the message
disappear.
17) Program the scalar to be able to show the coming mode.
18) Process the OSD display.
19) Read the keyboard. Is the power key pressed?
http://www.wjel.net

AOC LM565
17
5.3 Electrical Block Diagram
5.3.1 Main Board
MCU
W78E65
(U601)
Scalar IC TSU13AK
(Include ADC, OSD)
(U401)
EEPROM
24LC16B
(U602)
EEPROM
M24C02
(U301)
H sync
V sync
RGB
DB15_SDA,
DB15
_
SCL
EPR_SDA
EPR_SCL
LCD Interface
(CN503)
Key Board
Control
D-Sub
Connector
(CN301)
Crystal
14.318MHZ
(X401)
http://www.wjel.net

AOC LM565
18
5.3.2 Inverter/Power Board
EMI filter
Bridge
Rectifier
and Filter
Start Circuit
R906, R907
PWM
Control IC
Over
Voltage
Protect
AC input
5V
12V
PWM
Control IC
Feedback
Circuit
OSC and
Output
Circuit
DC Convert
Circuit
MOSFET
Q203/Q204
Over
Voltage
Protect
Lamp
ON/OFF
ON/OFF
Control
Rectifier
CMOS
Feedback
Circuit
Transformer
CN102
DIM
http://www.wjel.net

AOC LM565
19
6. Schematic
6.1 Main Board
715L1237-1-3
VCC2.5
VLCD
B1
3.INPUT
RIN
GIN
BIN
VSYNC
GNDR
GNDG
GNDB
ST_DET1 HSYNC
SOGDDC_CLK
DDC_DAT
ST_DET2
R+
R-
G-
G+
B+
B-
CLK+
CLK-
TXD
RXD
VCC3.3
B5
5.PANEL INTERFACE
VLCD
PB[0..9]
PA[0..9]
B4
2.POWER
onPanel_5V/3.3V
onBACKLITE
AdjBACKLITE
VCC3.3
VCC2.5
VAA1
VAA2
VAA3
VAA4
VCC5V
VCC12V
VLCD
VCPU
VLCD
VAA4
VCC5V
VCC12V
VCC12V
VCPU
TSU13AK for AOC
VCC2.5
VAA1
VCPU
B3
6.MCU
onBACKLITE
ST_DET2
onPANEL_5V/3.3V
SDA
INT
CSZ
DDC_DAT
ST_DET1
SCL
HWRESET
DDC_CLK
Volume
VCC5V
VCC12V
VCPU
RXD
TXD
AD0
AD1
AD2
AD3
VAA4
VCC3.3
PB[0..9]
VAA3
TSU13AK SCHEMATIC
VAA2
B2
4.SCALER
RIN
GIN
SOG
BIN
GNDR
GNDG
GNDB
HSYNC
VSYNC
R+
R-
G-
G+
B+
B-
CLK+
CLK-
CSZ
SCL
SDA
HWRESET
INT
Volume
AdjBACKLITE
PA[0..9]
PB[0..9]
VCC2.5
VCC3.3
VAA1
VAA2
VAA3
VAA4
AD0
AD1
AD2
AD3
VAA3
VAA2
PA[0..9]
VCC5V
VAA1
TOP
D
B
16Wednesday, April 14, 2004
Title
Size Document Number Rev
Date: Sheet of
http://www.wjel.net

AOC LM565
20
VAA2
ON_OFF
+
C215
47uF/16V
VCPU
VCC5V
C205
0.1uF
TSU13AK for AOC
R206
10K 1/16W
VCC12V
R202
10K 1/16W
onBACKLITE 6
VCC5V
D202
GS1D
R215
100K 1/16W
VAA3
VCC5V
C214
0.1uF
C
BE
GND
GND DIM
CN201
CONN
2
4
6
8
10
12
1
3
5
7
9
11
U201
RT9164
3 2
1
VI VO
GND
C207
0.1uF
VCC3.3
VCC5V
VCC5V 3,4,6
onPanel_5V/3.3V6
R211
10K 1/16W
VCC12V
NEW
Circuit
VCC3.3
C201
0.1uF
FB201
600 OHM
C217
0.068uF
VCC3.3 4
GND
C216
0.1uF
Q202
PMBS3904
32
1
VCC12V 6
VAA1
VAA4
VCC12V
VAA1 4
SOT-252
C
BE
U202
AIC1084-33M
3
1
2
VIN
ADJ
VOUT
VLCD 5
+
C208
100uF/16V
R203
1K 1/16W
+
C204
220uF/25V
VLCD
C206
1uF/25V
GND
R210
NC
R205 4.7K 1/16W
Q203
AO3401
VCC12V
VCC5V
VCC5V
GND
C203
0.1uF
D201 SS14
R209
0 1/16W
R213
NC
+
C202
220uF/25V
Q204
PMBS3904
32
1
VAA4 4
VAA2 4
R201 4.7K 1/16W
C212
0.1uF
VAA3 4
VCC5V+
VCC5V
VCC5V+
Brightness
VCC2.5
+
C211
47uF/16V
TO-263
VCC5V+
R208
10K 1/16W
R212 4.7K 1/16W
R207
4.7K 1/16W
Q201
PMBS3904
32
1
C210
0.1uF
AdjBACKLITE4
R214 delete
POWER
D
B
26Friday, November 26, 2004
Title
Size Document Number Rev
Date: Sheet of
VCC5V
R216
4.7K 1/16W
GND
R204
10K 1/16W
VCPU 6
VCC2.5 4
http://www.wjel.net
Table of contents
Other AOC Monitor manuals