AOC AD110DX User manual

F
K
8
F
K
I
G
A
B
DE
FGH
IJK
L
G(Long screw)
C (L-Plate)
=+
C
C
L-Plate Turner
M4x12MM M5x12MM
Step1
Step 3
Step 2Step 2
Step1
Step 3
Packing Lilst
A. Clamp-Mounting Procedure
B. Hole-Mounting Procedure
Monitor Size: 13"~32" Weight
Capacity: 2~9 kg
VESA Size: 75x75 mm, 100x100 mm
AD110DX
AD110DX/86
Ergonomic Monitor Arm
User Manual
A. Clamp-Mounting
B. Hole-Mounting
C. Cable-Management
D. VESA Mount Installation
E. Monitor Angle Adjustment
Tighten the 3 screws
(black only) to the arm
base.
Secure base B firmly on
desk, then hop on the
whole monitor arm.
Note:
Before hopping on the monitor arm,
adjust the base to the desired
height, then tighten the security
screws of the monitor arm into the
lock position.
Note:
Before hopping on the monitor arm,
adjust the base to the desired
height, then tighten the security
screws of the monitor arm into the
lock position.
Once L-Shape is secured,
hook it on the base-tuner.
Insert screws from (E)
into(H) plate, tighten the
3 screws (D) onto the
arm base.
Hop on (G) into the
bottom twister (E)
according to the
tickness of table.
Warning:
Please make sure to
tighten the screws.
Warning:
Please make sure to
tighten the screws.
Warning:
Please make sure to
tighten the screws.
1
/
2

Step 2
Step 1
C. Cable Management
D/E
5 MM
+60 -45
Pull out
upper
compartment.
Unscrew bottom
compartment
Q&A
1) Why monitor arm is hard to press down?
It is normal to feel pressure while pressing down without a monitor. Once
the monitor is mounted, the weight of itself helps to reduce the air-
pressure, then the arm will be easy to press down.
2) Why my monitor cannot move lower or higher freely?
Please adjust the "+" or "-" for best experience. Please do check your
monitor weight, if > 9kg, arm will not hold.
3) Why my Type-C does not charge?
Each Type-C cable has different materials and please reverse the cable
to try again.
Warning:
Please make sure to
tighten the screws.
Tighten screws
D. VESA Mount Installation
Manually tighten A or
B onto the top 2
holes, then hook on
the monitor. Please
do not fully tighten
until monitor
is stable.
Monitor Weight Adjustment "+" Increase weight capacity
"–" Decrease weight capacity
Note: Please ensure monitor is within the 2~9 kg weight range.
Condition 1: After attached, your monitor is freely movable in any
direction without adjustment.
Condition 2: After attached, monitor will bounce up, please use
wrench provided to turn "-" counterclockwise until stable.
Condition 3: After attached, monitor will fall down, please use
wrench provided to turn "+" clockwise until stable.
Once monitor is stable, tighten
top 2 and bottom 2.
E. Adjust Monitor Angles
AFTER INSTALLATION, ADJUST
GAS-SPRING POWER
1. Ensure monitor is tightened to monitor arm
2. Ensure monitor is not over-weight (2-9kg)
Weight Adjustment
Reduce Arm
Weight Capacity
Increase Arm
Weight Capacity
Warning
Warning
Envision Peripherals Inc.
490 North McCarthy Blvd. Suite #120 Milpitas, CA
95035
AOC International (Europe) B.V.
Prins Bernhardplein 200, 1097 JB Amsterdam, The
Netherlands
www.aoc.com
Made in China
2/
2