Apco Imsystem Instruction manual

2/02/17

General

Instructions

Projection Wall Mount / Ceiling Mount / General Care & Maint.

2/02/17

General

Instructions

Removal & Replacement of Inserts

Replacing Damaged PresLocks

PresLocks may be damaged if the sign insert is not properly aligned with

the sign holder. Never force an insert, especially if it offers resistance.

Should the "prongs" become damaged, usually the three "prongs" can

be realigned. If not, the damaged PresLock may need to be replaced.

Several replacements are sent with each order. If you need more,

telephone and they will be supplied without charge.

Follow these steps:

1. Pry damaged PresLock from holder using sharp object

(Fig. 1)

2. Clean any adhesive residue from back of sign insert with isopropyl

alcohol.

3. Press new PresLock into holder (Fig. 2)

4. Peel paper backing from adhesive on PresLock (Fig. 3)

5. Replace insert into holder applying pressure to adhere PresLock to the

backside of the insert.

6. The adhesive will not achieve full strength for 1 hour.

Projection Wall Mount (PWM)

Your IM System/SignMatch order may incorporate wall projections signs

of the IM System OR APCO’s Standard Overhead system featuring 1/2”

thick panels (shown here). Functionality and installation of the mounting

bracket are the same for both options.

See IS464 Projection Wall Mount instruction sheet included with the

shipment for detailed instructions or visit www.apcosigns.com.

Removing an Insert from the Holder

A Suction Cup Tool (SCT) is included with your order. It is provided to

remove a sign insert from its holder. Please keep the SCT for future use.

IM System/SignMatch inserts are retained within the holder and removed

in one of two ways:

1. PresLocks

PresLocks are round, plastic fasteners that are adhered to the back of

ADA (tactile/Braille) inserts and certain sizes of non-ADA, opaque

inserts and snap into receptacles within the plastic holder.

Removal

For the inserts, press the SCT firmly onto the sign insert, near to an

edge (Fig. 1) and pull the SCT outward.

Replacement

To replace the insert, position it flat into the holder and then press the

insert into the holder so that the PresLocks snap into the holder’s

receptacles.

2. SnapLock

All ClearLens inserts and certain opaque inserts feature a 3-point or

4-point tab design that engages the insert to the holder. (Fig 2)

Removal

Press an APCO Suction Cup Tool (SCT) onto the insert, near the

top/middle. Gently flex the upper rail of the holder and pull the SCT

outward (Fig 3).

Replacement

Gently flex the upper rail of the holder, line up the bottom tabs of the

insert with the corresponding holder notches and then press the top

of the insert into the holder (Fig 4).

Fig. 1

Fig. 2

Fig. 4

Fig. 3

PresLock

Paper Backing

Ceiling Mount (CM)

See IS463 Ceiling Mount instruction sheet included with the shipment for

detailed instructions or visit www.apcosigns.com.

IM System/SignMatch products are designed to provide years of

trouble-free service, but proper care is essential.

Always clean by wiping with a soft, lint-free, damp cloth, taking care to

wipe gently, not rub. Using a very mild solution of liquid hand soap and

lukewarm water is optional. If cleaning with liquid and/or damp cloth,

take care not to make contact with any subsurface, paper sign displays

as they may be damaged by the moisture.

IMPORTANT

Avoid using products such as window cleaners, liquids containing

ammonia, scouring compounds or solvents of any kind (i.e. alcohol,

acetone, etc) as the may damage the sign’s finish.

IMPORTANT REGARDING ADA SIGNS

ADA (tactile & Braille) signs are only suited for interior, climate-controlled

environments. Regular exposure to high humidity and temperature

extremes may result in sign deterioration.

General Care and Maintenance

APCO

388 Grant Street, SE, Atlanta, Georgia USA 30312-2227 Toll Free 877-988-APCO (2726) www.apcosigns.com IS411

APCO

388 Grant Street, SE, Atlanta, Georgia USA 30312-2227 Toll Free 877-988-APCO (2726) www.apcosigns.com IS411

Pin Mount (PIN)

It is necessary for pins to be in a vertical position in order to be mounted

properly to fabric panels (see Fig. 1). The pins swing freely from side to

side, but must always remain parallel to the holder ends.

DO NOT PULL PINS OUTWARD, as they may break off or become

separated from holder (see Fig. 2).

When installing, place holder at a slight angle and insert pins into fabric

panel (see Fig. 3).

When removing, DO NOT PULL OUT AT A SEVERE ANGLE, as the pins

may break off or the fabric may be damaged (see Fig. 4). For correct

removal, simply lift holder straight up (see Fig. 5).

Fig. 1

Correct

Fig. 2

Incorrect

Fig. 3

Correct Position

Fig. 4

Incorrect Position

2/02/17

General

Instructions

Installation (Vinyl Tape, Mechanical, Pin Mount)

2/02/17

General

Instructions

Panel Clip Attachment

Vinyl Tape

If your sign holder was supplied with Vinyl Tape (VT) mounting, strips of

double-sided tapes are already affixed to the back side.

As with all adhesives, the user must insure the surface to which the sigh

holder is to be mounted is Clean, Dry and free from any form of grease,

oil or silicones. If the sigh holder is to be affixed to a wood, the surface

must have been sealed with a varnish or lacquer prior to attachment.

Textured wall covering and some vinyl wall covering may reject

double-sided tape. The sigh holder may appear to adhere initially, but

may release shortly thereafter. For this reason, it is advisable to perform

a test with a single sign holder, prior to installing all holders. Usually 24

hours is sufficient to determine if tape and wall covering are compatible.

If the wall covering rejects the tape, a Silicone Adhesive, such as such

as Worksite®clear silicone sealan can be used to supplement the tape,

as the tape will hold the sign holder in place until the silicone adhesive

sets up. Again, a test for suitability with a single sign is advisable.

VERY IMPORTANT - READ BEFORE PROCEEDING.

Referencce APCO’s IS456 Vinyl Tape Info instruction sheet at

www.apcosigns.com for more information.

Mechanical Fasteners

While double sided tapes are widely used in place of mechanical

fasteners, some conditions may warrant the use of screws and other type

fasteners. Because of the wide range of mounting surfaces, Mechanical

Fasteners are never included. A broad range of suitable fasteners can

usually be found locally.

Panels from 1-1/8" to 1-11/16" Thick

1. Place Part B over back of partition/panel (long leg down, short

leg on top). See Fig.1 below.

2. Peel Double-Sided Tape backing off underside of Part A.

3. Place Part A over front of partition/panel, align left to right and

slide down onto top of Part B. See Fig.1 below.

NOTE: Apply pressure to tape line to assure adhesion.

4. Remove Panel Clip from partition/panel. Engage Panel Clip Hook

into Sign Holder Slot (see Fig.2 below). Dimension from top of

partition/panel to holder is fixed at 2-1/4".

5. Hang Panel Clip with Holder over partition/panel.

Panels from 1-11/16" to 2-3/16" Thick

1. Place Part B over back of partition/panel (short leg down, long

leg on top).

2. Follow 2-5 above instructions.

NOTE: Once Panel Clip is assembled, it cannot be used on a

partition/panel of greater thickness and may not function

properly on a partition/panel of lesser thickness.

2-1/4"

Part A

Accomodates

1-1/8" to 1-11/16"

Partition/Panel

Thickness

(Short Leg)

Part B

(Long Leg)

Sign Holder

Part A

Accomodates

1-11/16" to 2-3/16"

Partition/Panel

Thickness

(Long Leg)

Part B

(Short Leg)

Fig. 2

Sign Insert

Part A

Slot

Back of

Sign Holder

Double-Sided Tape

(on underside)

Hook Engages with

Sign Holder Slot

Typical Office

Partition/Panel

Fig.1

APCO

388 Grant Street, SE, Atlanta, Georgia USA 30312-2227 Toll Free 877-988-APCO (2726) www.apcosigns.com IS411

APCO

388 Grant Street, SE, Atlanta, Georgia USA 30312-2227 Toll Free 877-988-APCO (2726) www.apcosigns.com IS411

Fig. 5

Correct Position