APEX Customs GRASSHOPPER 2.0 User manual

the
GRASSHOPPER
2.0
12mm Mini Dual Action
Random Orbital Polisher
Bringing back that showroom shine
To reduce risks associated with the use of the polisher, please
carefully read the following instructions.
Work area
• Do not operate the polisher while near or exposed to
flammable liquids or gases.
• Keep a safe distance from bystanders while operating the
polisher.
Electrical safety
• There should be no modification of the polisher in any way.
• Avoid body contact with earthed or grounded surfaces such
as pipes, radiators, ranges and refrigerators.
• Do not expose the polisher to water or leave it in an area
where it may become wet.
• Do not use the polisher in any wet weather conditions.
• Keep the cord away from any heat, oil, sharp edges or
moving parts.
Personal safety
• Do not use the polisher while you are tired or under the
influence of drugs, alcohol or medication.
• Use personal protective equipment such as safety glasses
and gloves.
• Ensure the switch is in the off position before connecting to
a power source.
• Remove any adjusting key or wrench before turning the
polisher on.
Polisher use and care
• Do not use the polisher if any of the parts are broken,
misaligned or showing signs of excessive wear.
• Disconnect the plug from the power source before making
any adjustments, change in accessories or when storing the
polisher.
• Keep the polisher clean and well maintained to prolong its
intended life cycle. If damaged, have the polisher repaired by
an authorised repairer or contact the Apex Customs
customer support team for further information.
Service
• Please note that the standard 12 month warranty from date
of purchase will be void if your polisher has been tampered
with or serviced by a non qualified Apex Customs repairer.
Only use original parts supplied by Apex Customs.
Stay safe
!
6000
5000
4000
3000
2000
1 2 3 4 5 6
OPM
The grasshopper 2.0 specifications
Pad size compatibility
75mm / 3”
Max power
600 Watts
Variable speeds
2000 - 6000 OPM
Max noise levels
63dB @1m
Orbit size
12mm
Weight
2kg
Voltage
220 - 240V AC
KG
apexcustoms.com.au
Register your Apex Customs polisher
online, and we will keep track of the
paperwork for you.
Visit bit.ly/apex warrantyredeem
or scan the QR code.
Warranty

1. NEVER start the machine before the
backing pad is installed.
2. Align the backing pad with the foam
pad's center. Otherwise, vibration may
be excessive.
3. Generally, lower speeds are
recommended for tight work areas
while higher speeds are ideal for
larger surface areas.
4. To prevent burning through paint, use
very light pressure and keep the
polisher moving constantly.
5. Use the polisher at low speeds while
polishing rough surfaces.
6. For tricky or tight areas, use
"coast-down" to polish. To do so, turn
the machine on for a few seconds to
enable it to oscillate, then turn it off
and use the residual oscillations to
polish.
Troubleshooting
1. If the polisher does not start, check the following:
• Is the power source active?
• Is the power cable on the the machine damaged?
• Are any screws on the switch loose?
• Is the switch or the speed controller damaged?
• Is the armature or stator damaged?
Best practice
2. If large sparks are visible from the side vents of the
machine, the carbon brushes may need to be replaced.
Kindly contact the Apex Customs customer support team
for further information on how to replace these.
3. If the machines become noticeably noisier over time, stop
using immediately and inspect if the bearings or counter
weight are damaged / misaligned.
Key features
?
Non-slip soft
rubber coated grip
CNC machined
counterweight
Switch self-locking button
Keep the switch locked whilst
the polisher is running
Constant speed controller
6 speed setting
3” interchangeable
backing plate
Housing lock nut
Air vents
Do not cover
during operation
4 meter cord