Aqua EZ RVP31 User manual

Have a question or need a part?
Our customer service team is available to help
Mon - Thurs: 8AM to 5PM EST Friday: 8AM to 3PM EST
RECHARGEABLE POOL VACUUM
USER MANUAL
LIMPIAFONDOS INALÁMBRICO RECARGABLE
MANUAL DE USUARIO
Please contact us directly at
Toll Free: [phone] Web: www.aquaez.com

1
PARTS DIAGRAM
Have a question or need a part?
Our customer service team is available to help
Mon - Thurs: 8AM to 5PM EST Friday: 8AM to 3PM EST
1
Main body
2
Locking hole (for pole
connector /handle)
3
Locking button (for
transparent canister)
4
Transparent canister
5
Water draining valve
6
Suction nozzle flap
7
Filter cage
8
Telescopic pole
connector
9
Pivoting suction head
(with side brushes)
10
Brushes
11
Side Brushes
12
Wheel
Battery: Rechargeable Li-ion battery pack –
2000mAH, 7.4V, 14.8Wh
Charging voltage : 8.4V DC, 1.0 A
Motor: 7.2V DC
13
Sliding brush
14
Flat Suction Nozzle
15
Charger base
16
Power ON/OFF
button
17
Protective cap
Please contact us directly at
Toll Free: [phone] Web: www.aquaez.com

2
SAFETY WARNINGS & INSTRUCTIONS
Read and follow all instructions in this manual and on the equipment. Failure to do so
could result in severe or fatal injuries.
WARNING!
-This is not a TOY. Children should be kept out of reach from this pool vacuum and
its accessories.
-Never allow children to operate this product.
-This pool vacuum is not intended for use by someone with reduced physical,
sensory or mental capabilities, or a lack of experience and knowledge unless they
have been given instructions concerning the appliance and are under supervision
of the person responsible for their safety.
-Make sure the pool vacuum is fully immersed in the water before operation. The
minimum water level required to operate the device must reach above the power
button of the pool vacuum when it is held in a vertical position. Operating the pool
vacuum when it is not immersed in the water correctly could damage the unit and
void the warranty as a result.
-Maximum operating depth in water is 3 meters (10ft).
-Maximum water temperature: 5˚C(41˚F) –35˚C(95˚F)
-DO NOT use power extension cords.
-Connect the external adaptor to a power source through a ground fault circuit
interrupter (GFCI). If in doubt, consult a qualified professional electrician.
-Do not use this pool vacuum if any damage is detected.
-Replace damaged parts as soon as possible. Only use parts certified by the
distributor or manufacturer.
-Turn off the power, disconnect the external adaptor from the power source, and
unplug the external adaptor from the charging base before detaching the pool
vacuum from the charging base.
-Disconnect the pool vacuum from the supply mains prior to carrying out user
maintenance such as cleaning the filter.
-Detach the pool vacuum from the charging base and make sure the pool vacuum
is OFF before servicing the product.
-Battery installed is a rechargeable Li-ion battery pack. Never attempt to replace
the battery pack.
-The pool vacuum is only to be used with the external adaptor delivered with this
product.
-You should not operate this pool vacuum when people/pets are present in the
water.
-DO NOT use this pool vacuum without an intact filter cage in place, as your
warranty will be voided as a result.
-Suction entrapment hazard: This pool vacuum generates suction. Do not allow
hair, body, or any loose parts of your clothing to make contact with the suction
hole of the pool vacuum during its operation.
-Never insert body parts, clothing or other objects into the openings and moving
parts of the pool vacuum.
-DO NOT use this pool vacuum to pick up any toxic substance, flammable or
combustible liquids such as gasoline, or in the presence of explosive or flammable
fumes.
-Never attempt in any way to disassemble this pool vacuum.

3
-Under no circumstances should you attempt to disassemble the pool vacuum and
replace the impeller, motor, and battery by yourself.
-Never insert any object to touch the impeller.
- External adaptor and charging base:
For indoor use only.
Never use the external adaptor and charging base for anything other than
charging the battery of the pool vacuum that is supplied in the same pack.
The external adaptor and charging base should not be used outdoors, nor
exposed to rain, humidity, any liquid or heat.
Keep the external adaptor and charging base out of reach of children.
Never use the external adaptor and charging base if any damage is
detected.
DO NOT handle the external adaptor and charging base with wet hands.
DO NOT handle the pool vacuum, external adaptor, and charging base
while charging with wet hands and without shoes.
Keep the external adaptor disconnected from power when it is not in use.
Never attempt to open the external adaptor and charging base.
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or an equally-qualified person in order to prevent hazards of
any kind.
Make sure the pool vacuum and the charging base are completely dry
before charging.
CAUTION!
- This pool vacuum is designed for underwater use only; it is not an
all-purpose vacuum cleaner. DO NOT attempt to use it to clean anything
other than your pool / spa.
- Use only original accessories delivered with this product.
- DO NOT use this pool vacuum right after pool-shocking. It is
recommended to leave the pool circulating for at least 24-48 hours.
- It is not recommended to use this pool vacuum with another pool
vacuum/cleaner simultaneously.
- Avoid picking up hard, sharp objects with this product. They may
damage the pool vacuum and filter.
- Exercise caution when cleaning pool stairs.
- Only use the charging base for its intended purpose as outlined in this
manual.
- To avoid damaging the external adaptor and the cord, do not carry the
pool vacuum by the cord or pull the cord to disconnect it from the power
source and product.
- Charge the pool vacuum indoor in a clean, dry area with good ventilation
and an ambient temperature between 5˚C(41˚F) and 30˚C(86˚F).
- DO NOT leave the pool vacuum charged for over 20 hours.
- If the pool vacuum will not be used for an extended period, detach it from
the charging base and use a damp cloth to clean and dry the pool
vacuum and accessories. Make sure to charge the pool vacuum
completely before it is stored. Store in a well-ventilated area away from
sunlight, heat, ignition sources, pool chemicals, and children. Never

4
leave the pool vacuum plugged in for long-term storage. Recharge the
pool vacuum every three months.
Above warnings and cautions are not intended to incorporate all possible
instances for risks and / or severe injuries. Pool / spa owners should always
exercise extra caution and common sense when utilizing the product.
GETTING STARTED
IMPORTANT NOTE: Fully charge the pool vacuum before using it for the first time.
Charging the battery
WARNING!
Charging must be done indoors, in a well-ventilated area away from sunlight,
children, heat, ignition sources, and with an ambient temperature between 5˚C(41˚F)
and 30˚C(86˚F).
Never use the external adaptor and charging base if any damage is detected.
Use only the original external adaptor provided.
Make sure the pool vacuum and the charging base are clean and dry before set-up.
Place the unit on a flat surface. Open the protective cap on the end of the body and
align the 2 pins of the charger base above the charging sockets. WARNING! Make
sure not to invert the position of the charger base. Press the charger base onto the
rear body until it the pins are inserted completely into the sockets. Plug the female
jack of the external adaptor into the charging port at the end of the charging base.
Important note:
Close the protective cap tightly after charging before operation
In case, charging sockets gets wet, dry the area completely (eg, using cotton bud)
before charging.

5
WARNING!
DO NOT handle the pool vacuum, external adaptor and charging base while it is
charging with wet hands and without shoes.
Connect the external adaptor to the power source through a ground fault circuit
interrupter (GFCI).
Charge the pool vacuum with the original external adaptor provided.
DO NOT use power extension cords.
Fully charge the battery before first use.
Charging must be done indoors, in a dry & well-ventilated area away from sunlight,
children, heat, ignition sources, and with an ambient temperature between 5˚C(41˚F)
and 30˚C(86˚F).
Always disconnect the external adaptor from the power source when charging is
complete.
Do not leave the pool vacuum in charge for over 20 hours.
Immediately turn the power off and disconnect the external adaptor from the power
source if you detect any of the following conditions:
- Offensive or unusual odor
- Excessive heat
- Deformation, cracks, leaks
- Smoke
1. Make sure that the pool vacuum is turned off prior to charging.
2. Connect the external adaptor to the power source. Once the pool vacuum begins
charging, the indicator light on the external adaptor will turn red. Normally, it takes
about 4- 5 hours to reach a full charge. The indicator light will turn green when the
pool vacuum is almost fully charged.
Note: If the motor is generating noise, immediately turn off the device by pressing the
ON/OFF button. Otherwise, it could potentially lead to failure of the shaft seals / motor,
and the warranty will be voided as a result.
Note: Charge the pool vacuum completely (about 4-5 hours) prior to the first use.
3. When charging is complete, disconnect the external adaptor from the power source
and unplug the jack from the charging base.
4. Detach the charger base from the pool vacuum.
Normally, the pool vacuum can be operated up to 30 minutes on a full charge
(charged for 4-5 hours)
FACT: Rechargeable lithium-Ion battery is classified as a consumable item. It has a
limited life and will gradually lose its capacity to hold a charge. Therefore, running
time of the pool vacuum will gradually reduce through repeated charging and
discharging in operation.
NOTE: Let the pool vacuum rest for 30 to 40 minutes before charging it again.

6
Set-Up Before Use
Telescopic pole connector assembly
Press down the side pins of the connector/handle and insert it inside the main body.
Turn the connector in either direction until the pin is secured in the hole, as shown in
the diagram.
Telescopic pole assembly
Note: a V-clip is installed inside the pole connector to secure the telescopic pole (not
included) in position. Slide the telescopic pole onto the pole connector. Press on the
side pins of the connector and slide the telescopic pole further down until the pins of
the connector are secured inside the holes of the pole.
To release the telescopic pole, press down the side pins simultaneously and pull out
the pole.
Suction head assembly
Insert the suction head directly into the suction mouth of the pool vacuum until the
side tabs of the transparent case clip in the holes of the suction head’s pivot.
NOTE: To replace the brushes on the suction head, lift one end and pull the brush out
to make space for a new one.

7
WARNING! For vinyl liner and fibreglass pools, it is recommended to keep the
brushes on the suction head to avoid damaging the pool.
OPERATION
WARNING!
Do not use the pool vacuum if any damage is detected.
Oil stain could occur due to possible leakage of lubricants applied to the O-ring.
Do not operate this pool vacuum if there are people/pets present in the water.
Make sure the pool vacuum is fully immersed in the water before initiating operation.
The minimum water level required to operate the device must reach above the
power button of the pool vacuum when it is held in a vertical position. Operating the
pool vacuum when not immersed in the water correctly can damage the unit and
the warranty will be voided as a result.
Maximum operating depth in water is 3 meters (10ft).
Maximum water temperature:5˚C(41˚F) –35˚C(95˚F)
DO NOT use the pool vacuum without an intact filter cage in place. Using your pool
vacuum without an intact filter cage in place will VOID your warranty.
Suction entrapment hazard: This pool vacuum generates suction. Do not allow hair,
body or any loose parts of your clothing to make contact with the suction mouth of
the pool vacuum during its operation.
Never insert body parts, clothing or other objects into the openings and moving
parts.
DO NOT use this pool vacuum to pick up any toxic substance, flammable or
combustible liquids such as gasoline, or operate in the presence of explosive or
flammable fumes.
DO NOT cover the side slot of the cleaner body during operation. The
impeller/motor may be damaged as a result.
Never insert any object to touch the impeller.
CAUTION
Use only original accessories delivered with this product.
DO NOT use this pool vacuum immediately after pool-shocking. It is recommended
to leave the pool circulating for at least 24-48 hours.
It is not recommended to use this pool vacuum with another pool vacuum/cleaner
simultaneously.
DO NOT leave the pool vacuum in the water when it is not in use or when battery is
low as water leakage may occur.

8
1) Bring your pool vacuum to the side of your pool / spa. Immerse the pool vacuum in
water and press the power button to initiate operation.
CAUTION! Make sure the pool vacuum is always facing downwards when it is placed
into the pool. Otherwise it may bend the pole connector and damage it during the
process.
2) To remove the pool vacuum from the pool / spa, lift the pool vacuum while pointing
it downwards in order to allow water to escape from the outlet valve. Water is going to
escape via the handle / pole connector and draining holes inside the handle chamber
on the rear body.
CAUTION! Make sure the pool vacuum is always facing downwards when it is
removed from the pool. Otherwise, the pole connector may be bent and damage the
pool vacuum in the process.
3) Rinse the pool vacuum with fresh water after every use. DO NOT use any
detergent.
EMPTYING THE FILTER
WARNING! Using the pool vacuum without a filter cage in place will VOID
your warranty.
In order to maximize the cleaning efficiency, be sure to clean the filter cage before
and after each use.
CAUTION! If the pool vacuum is charging, disconnect the external adaptor from the
power source and detach the pool vacuum from the charger base.
Emptying the filter cage
1. Place the pool vacuum on a stable surface.
2. Press the locking button until the locking hole on the clear canister is released.
Slide the canister away until the notch on the bottom of canister opening is released
from the hook on the bottom of main body. Remove the filter cage from the main
body.
CAUTION! Replace the damaged filter cage immediately before the next operation.
3. Clean out the debris and rinse the filter cage with water. If brushing is deemed
necessary, use only a soft brush to clean the cage gently and carefully.
4. Re-position the filter cage inside the main body. Make sure the filter cage is
completely inserted inside the main body.

9
To re-install the canister, first align the notch of the canister with the hook on main
body and then press the canister onto main body. Make sure the locking hole on the
clear canister is secured with the locking button.
MAINTENANCE & STORAGE
NOTE:
1. Battery discharges on its own during storage. Make sure to fully-charge the pool
vacuum before storage.
2. You must re-charge the battery at least once every three months when it is not in
use.
Unplug the external adaptor from socket and then unplug the adapter jack from the
charging base.
Detach accessories from the pool vacuum. If necessary, rinse the pool vacuum and
accessories with fresh water. DO NOT use detergent.
Make sure to drain the water from the unit, handle and pole connector.
Use a damp cloth to clean and dry the pool vacuum and its accessories.
Store them in a well-ventilated area away from the sunlight, children, heat, ignition
sources, and pool chemicals. Ambient temperature for storage should be 10˚C –
25˚C (50˚F –77˚F). NOTE: A higher temperature may reduce the battery life during
storage.
WARNING!
-Never attempt in any way to disassemble the pool vacuum.
-Under no circumstances should you attempt to disassemble the pool vacuum and
replace the impeller, motor and battery by yourself.
CAUTION!
Excessive heat can damage the battery and reduce its lifespan as a result.
The battery supplied with your pool vacuum lasts for about 300 charging cycles
(with proper charging and operation). Replace your pool vacuum with a new battery
if the following happens. Consult your dealer regarding battery replacement.
- Battery appears damaged or will not charge fully.
- Battery operation time is noticeably reduced. Observe and note down
the run times of operation of the first few times (on a full charge). Use
these run times as a reference point to compare run times with older
batteries.
The battery must be removed from the pool vacuum before it is scrapped.
The pool vacuum must be disconnected from the supply mains when removing the
battery

10
The battery is to be disposed safely and according to local ordinances or
regulations.
NOTE: Incorrect maintenance may reduce the battery life and affect its capacity as a
result.
BATTERY DISPOSAL
Your pool vacuum battery is a maintenance-free rechargeable lithium-ion battery
pack, which must be disposed properly. Recycling is required; please contact your
local authority for information.
WARNING!
Never attempt to disassemble a battery pack
Remove all personal items such as rings, bracelets, necklaces and watches when
the battery pack is unwired from the pool vacuum.
A battery can produce a short circuit current high enough to weld a ring (or similar
item) to metal, causing a severe burn in the process.
Wear complete eye protection, gloves and protective clothing when the battery
pack is being removed.
Avoid touching the wires altogether and avoid allowing them to make contact with
any metal items, which could cause sparking and/or short circuit the battery.
Never smoke or allow a spark or flame in the vicinity of the battery or the pool
vacuum.
Do not expose the battery to fire or intense heat as this may result in an explosion.
CAUTION!
If a battery leak occurs, avoid contact with the leaking fluids and place the damaged
battery in a plastic bag.
-If leaking fluids come in contact with skin and clothing, wash immediately with
plenty of soap and water.
-If leaking fluids come in contact with eyes, immediately flush eyes with cool
running water for at least 15 minutes and do not rub them. Seek medical attention
as soon as possible.
How to remove the battery pack
Recommended tools (not included): Philips screwdriver and small slot screwdriver
1. Press on the locking button and detach the clear canister from the body. Use a
small screwdriver to detach the ring from the body. It is hard to detach the ring by
screwdriver, use cutting plier to cut.
2. Use Philips screwdriver to unscrew all the screws on the main body.

11
3. Separate the body in two halves to access the main chamber. Use a Philips
screwdriver to remove the end cover and access the battery pack.
4. Take out the battery pack from the main chamber. To detach the battery pack,
press the clip on the connector and pull it out. NOTE: Wrap the connector
immediately with insulating tape in order to avoid short circuit caused by the contact
of both wire terminals.

12
TROUBLESHOOTING
Problem
Possible Cause
Solution
Pool vacuum does not capture
debris
Battery is running out
Charge the battery again.
Impeller is jammed
Power off the pool vacuum and visually check the gap
in the middle of the pool vacuum to see if the impeller
is jammed by large debris. If possible, use a small tool
to remove the debris carefully. If necessary, contact
your dealer for further instructions.
WARNING!Make sure the pool vacuum is
powered off when the unit is being serviced.
Impeller is broken
Contact your dealer for impeller replacement.
Filter cage is full
Clean the filter cage.
Debris escapes from the filter
Suction nozzle flap is
broken
Suction nozzle flap works like a door to prevent debris
from escaping from the filter. Contact dealer for
replacement part and instructions.
Filter cage is damaged.
Replace with a new filter cage.
Outlet valve comes off.
Without the outlet valve, the pool vacuum might
capture debris through this opening. Contact dealer for
a valve replacement.
Telescopic pole connector
cannot be secured in assembly
Side pin on pole
connector is broken
Replace with a new pole connector.
Pool vacuum cannot be
charged / recharged
Battery is damaged
Contact dealer for battery replacement.
WARNING! DO NOT open the pool vacuum
and replace the battery by yourself. This could result in
severe or fatal injury and the warranty will be voided
as a result.
Contact pins of the
charger base and unit
are not connected.
Make sure that the charger base is assembled on the
unit properly and the contact pins are connected.
External adaptor
damaged
Contact dealer for replacement.
WARNING! Using the wrong external adaptor
will result in damaging the pool vacuum / battery and
voiding the warranty as a result.
Pool vacuum does not move
smoothly
Wheel is jammed
Clean out the debris from the wheel.
If soft copy of this instruction manual is required, please contact our customer service by email:
[email protected]m

13
DIAGRAMA DE LAS PARTES
1
Cuerpo principal
2
Orificio de bloqueo
(para conector para
pértiga/manija)
3
Botón de bloqueo (para
contenedor
transparente )
4
Contenedor
trasparente
5
Válvula de drenaje de
agua
6
Solapa de la boquilla
de succión
7
Filtro rígido
8
Conector de pértiga
telescópica
9
Cabeza de aspiración
pivotante (con cepillos
laterales)
10
Cepillos
11
Cepillos laterales
12
Rueda
Batería: paquete de baterías de iones de litio recargable,–
2000mAh, 7.4V, 14.8Wh
Tensión de carga:: 8.4V DC, 1.0 A
Motor: 7.2V DC
13
Cepillo dezlisante
14
Boquilla de aspiración
plana
15
Base del cargador
16
Botón de APAGADO /
ENCENDIDO
17
Capuchón protector

14
AVISOS E INSTRUCCIONES DE SEGURIDAD
Lea y siga todas las instrucciones contenidas en este manual y en el equipo. En caso
contrario, podría sufrir lesiones graves o mortales.
¡ATENCIÓN!
-Este dispositivo no es un JUGUETE. Mantenga a los niños lejos de esta
aspiradora de piscina y de sus accesorios.
-Los niños no deben usar este producto.
-Esta aspiradora de piscina no está diseñada para ser usada por personas con
discapacidad física, sensorial o mental, ni por personas con falta de experiencia y
conocimientos, a menos que hayan recibido instrucciones sobre el dispositivo y
sean supervisadas por la persona responsable de su seguridad.
-Asegúrese de que la aspiradora de piscina está totalmente sumergida en el agua
antes de usarla. El nivel mínimo de agua necesario para usar el dispositivo debe
estar por encima del botón de encendido de la aspiradora de piscina en posición
vertical. El uso de la aspiradora de piscina, si no está correctamente sumergida
en el agua, podría dañar la unidad y anular la garantía.
-La profundidad máxima a la que se puede usar el dispositivo es de 3 metros.
-Temperatura máxima del agua: 5˚C –35˚C
-NO se deben usar regletas de enchufes eléctricos.
-Conecte el adaptador externo a una fuente de alimentación mediante un
interruptor de circuito con fuga a tierra (ICFT). Si tiene alguna duda, consulte a un
electricista profesional cualificado.
-No use esta aspiradora de piscina si detecta cualquier daño.
-Sustituya las piezas dañadas lo antes posible. Sólo debe usar piezas certificadas
por el distribuidor o el fabricante.
-Desactive el dispositivo, desconecte el adaptador externo de la fuente de
alimentación y desenchufe el adaptador externo de la base de carga antes de
retirar la aspiradora de piscina de la base de carga.
-Desconecte la aspiradora de piscina de la alimentación eléctrica antes de realizar
cualquier operación de mantenimiento de usuario, como puede ser la limpieza del
filtro.
-Retire la aspiradora de piscina de la base de carga y asegúrese de que está
apagada antes de manipular el producto.
-La batería instalada es un paquete de baterías de iones de litio recargable. Nunca
debe intentar sustituir el paquete de baterías.
-La aspiradora de piscina sólo debe usarse con la unidad de adaptador externo
que se suministra con este producto.
-No debe usar esta aspiradora de piscina si hay personas/mascotas en el agua.
- NO use esta aspiradora de piscina sin un filtro rigido intacto instalados, ya que de
lo contrario la garantía quedará anulada.
-Peligro de atrapamiento por succión: Esta aspiradora de piscina genera succión.
No permita que su pelo, cuerpo o prendas sueltas entren en contacto con el
orificio de succión de la aspiradora de piscina cuando esté en funcionamiento.
-No introduzca nunca partes del cuerpo, ropa u otros objetos en las aberturas y
piezas móviles de la aspiradora de piscina.
-NO use esta aspiradora de piscina para recoger sustancias tóxicas, inflamables o
líquidos combustibles como gasolina, ni tampoco cerca de gases explosivos o
inflamables.

15
-No intente nunca desmontar la aspiradora de piscina.
-No intente, bajo ninguna circunstancia, desmontar la aspiradora de piscina y
sustituir el propulsor, el motor y la batería por sí mismo.
-Nunca debe introducir ningún objeto para tocar el propulsor.
- Adaptador externo y base de carga:
Sólo para uso interior.
Sólo debe usar el adaptador externo y la base de carga para recargar la
batería de la aspiradora de piscina suministrada en el mismo paquete.
El adaptador externo y la base de carga no deben usarse en el exterior, ni
exponerse a la lluvia, la humedad, al calor ni a ningún líquido.
Mantenga el adaptador externo y la base de carga fuera del alcance de los
niños.
Nunca debe usar el adaptador externo ni la base de carga si detecta
cualquier daño.
NO coja el adaptador externo ni la base de carga con las manos mojadas.
Mientras el dispositivo se esté cargando, NO manipule la aspiradora de
piscina, el adaptador externo ni la base de carga, con las manos mojadas y
sin zapatos.
Mantenga el adaptador externo desconectado de la corriente eléctrica
cuando no lo esté usando.
No intente abrir el adaptador externo ni la base de carga.
Si el cable eléctrico está dañado, debe ser sustituido por el fabricante, por
su representante de servicio o por un profesional cualificado, con el objetivo
de evitar cualquier peligro.
Asegúrese de que la aspiradora de piscina y la base de carga están
completamente secas antes de iniciar la recarga.
¡PRECAUCIÓN!
- Esta aspiradora de piscina sólo está diseñada para ser usada bajo el
agua; no es una aspiradora de uso general. NO intente usarla para
limpiar una superficie que no sea su piscina/spa.
- Sólo debe usar accesorios originales provistos junto con este producto.
- NO use esta aspiradora de piscina justo después de aplicar el
tratamiento de choque a la piscina. Se recomienda dejar circular el agua
de la piscina durante al menos 24-48 horas.
- No se recomienda usar esta aspiradora de piscina simultáneamente con
otra aspiradora o limpiador de piscina.
- Evite recoger objetos duros y afilados con este dispositivo. Podrían
dañar la aspiradora de piscina y el filtro.
- Tenga cuidado al limpiar las escaleras de la piscina.
- Sólo se debe usar la base de carga con el objetivo especificado en este
manual.
- Para evitar dañar el adaptador externo y el cable, no transporte la
aspiradora de piscina por el cable ni tire del cable para desconectarlo de
la fuente de alimentación y del producto.
- Recargue la aspiradora de piscina en una zona interior limpia y seca,
con buena ventilación y con una temperatura ambiente de entre 5˚C y
30˚C.
- NO deje la aspiradora de piscina cargando durante más de 20 horas.

16
- Si no va a usar la aspiradora de piscina durante un periodo de tiempo
prolongado, sepárela de la base de carga y use un paño húmedo para
limpiar y secar la aspiradora de piscina y sus accesorios. Asegúrese de
cargar totalmente la aspiradora de piscina antes de guardarla. Guárdela
en una zona bien ventilada y libre de luz solar, calor, fuentes de ignición
y productos químicos para piscina, fuera del alcance de los niños. No
deje nunca la aspiradora de piscina conectada si va a guardarla durante
un periodo de tiempo prolongado. Recargue la aspiradora de piscina
cada tres meses.
Los avisos y precauciones anteriores pueden no incluir todas posibles
situaciones de riesgo y/o lesiones graves. Los propietarios de piscina/spa
deben tener siempre mucho cuidado y sentido común al utilizar el producto.
PRIMEROS PASOS
AVISO IMPORTANTE: Recargue completamente la aspiradora de piscina antes de
usarla por primera vez.
Carga de la batería
¡ATENCIÓN!
La recarga debe realizarse en una zona interior, bien ventilada y libre de luz solar,
niños, calor, fuentes de ignición y con una temperatura ambiente de entre 5˚C y
30˚C .
Nunca debe usar el adaptador externo ni la base de carga si detecta cualquier
daño.
Use sólo el adaptador externo original provisto con el producto.
Asegúrese de que la aspiradora de piscina y la base de carga están limpias y
secas antes de instalarlas.
Coloque la unidad sobre una superficie estable. Abre el capuchón protector en la
parte trasera del cuerpo y alinee las dos fichas machos de la base de carga encima
de los orificios de carga. AVVETENZIA: Asegúrese de no invertir la posición de la
base de caga. Empuje la base de carga en la carcasa trasera hasta que las fichas
sean completamente inseridas dentro los orificios. Conecte la parte hembra del
adaptador externo dentro el orificio de carga localizada en la base del cargador.

17
Noticia Importante:
- Después de la recarga y antes de la próxima operación, cierre el capuchón
protector.
- Si los orificios de carga están mojados, secarlos completamente (por ejemplo
con un bastoncillo de algodón) antes de recargar la aspiradora.
¡ATENCIÓN!
Mientras el dispositivo se esté cargando, NO manipule la aspiradora de piscina, el
adaptador externo ni la base de carga, con las manos mojadas y sin zapatos.
Conecte el adaptador externo a la fuente de alimentación mediante interruptor de
circuito con fuga a tierra (ICFT).
Cargue la aspiradora de piscina mediante el adaptador externo original
suministrado.
NO se deben usar regletas de enchufes eléctricos.
Cargue completamente la batería antes de usarla por primera vez.
La recarga debe realizarse en una zona interior, seca, bien ventilada y libre de luz
solar, niños, calor, fuentes de ignición y con una temperatura ambiente de entre
5˚C y 30˚C .
Desconecte siempre el adaptador externo de la fuente de alimentación cuando
termine la carga.
No deje la aspiradora de piscina cargando durante más de 20 horas.
Desactive inmediatamente el dispositivo y desconecte el adaptador externo de la
fuente de alimentación si detecta alguna de las siguientes condiciones:
- Olor ofensivo o inusual
- Calor excesivo
- Deformación, grietas o fugas
- Humo
1. Asegúrese de que la aspiradora de piscina está desconectada antes de cargarla.
2. Conecte el adaptador externo a la fuente de alimentación. Cuando la aspiradora
de piscina empiece a cargarse, el piloto indicador del adaptador externo se pondrá
rojo. Normalmente se tardan unas 4-5 horas en conseguir una carga completa. El
piloto indicador se pondrá verde cuando la aspiradora de piscina esté casi cargada al
máximo.
Atención: Si el motor emite ruido, apague inmediatamente el dispositivo pulsando el
botón ON/OFF. En caso contrario, podría causar una avería de los sellos del eje / del
motor, por lo que la garantía quedaría anulada.
Atención: Cargue totalmente la aspiradora de piscina (unas 4-5 horas) antes de
usarla por primera vez.

18
3. Cuando la carga haya terminado, desconecte el adaptador externo de la fuente de
alimentación y desenchufe el conector de la base de carga.
4. Separe la base de carga de la aspiradora de piscina.
En condiciones normales, la aspiradora de piscina se puede usar hasta 30 minutos si
tiene carga completa (recargada durante 4-5 horas)
HECHO: La batería recargable de iones de litio está clasificada como un producto
consumible. Tiene una vida útil limitada y perderá gradualmente su capacidad de
retener la carga. Así pues, el tiempo de funcionamiento de la aspiradora de piscina
se reducirá gradualmente a medida que se cargue y se descargue la aspiradora por
su uso.
NOTA: Deje reposar la aspiradora de piscina durante unos 30 o 40 minutos antes de
volverla a cargar.
Montaje previo al uso
Montaje del conector de pértiga telescópica
Pulse los dos pasadores laterales del conector / manija y inserirlo dentro el cuerpo
principal. Giren el conector en cualquier dirección hasta que los pasadores queden
fijados en los orificios, como indicado en el diagrama.
Montaje de la pértiga telescópica
Nota: Un clip “V” esta instalado dentro el conector de pértiga para mantener en
posición la pértiga telescópica (no incluida). Inserte el conector dentro la pértiga
telescópica. Pulse los pasadores laterales del conector y deslice la pértiga
telescópica hasta que los pasadores laterales queden fijados en los orificios de la
pértiga.
Para liberar la pértiga telescópica, pulse los pasadores laterales simultáneamente y
tire la pértiga.

19
Montaje del cabezal de succión
Inserte el cabezal de succión directamente en la boquilla de succión de la aspiradora
de piscina hasta que. Las pestañas laterales de la carcasa transparente encajarán en
los orificios del pivote del cabezal de succión.
NOTA: Para sustituir los cepillos del cabezal de succión, levante el extremo y tire de
él para dejar espacio para uno nuevo.
¡ATENCIÓN! En el caso de piscinas revestidas de vinilo o piscinas de fibra de
vidrio, se recomienda mantener los cepillos en el cabezal de succión para evitar
dañar la piscina.
FUNCIONAMIENTO
¡ATENCIÓN!
No use la aspiradora de piscina si detecta cualquier daño.
Es posible que se generen manchas de aceite causadas por el derrame de
lubricante que se suele aplicar al anillo sellador.
No debe usar esta aspiradora de piscina si hay personas/mascotas en el agua.
Asegúrese de que la aspiradora de piscina está totalmente sumergida en el agua
antes de empezar a usarla. El nivel mínimo de agua necesario para usar el
dispositivo debe estar por encima del botón de encendido de la aspiradora de
piscina en posición vertical. El uso de la aspiradora de piscina, si no está
correctamente sumergida en el agua, puede dañar la unidad y anular la garantía.
La profundidad máxima a la que se puede usar el dispositivo es de 3 metros.
Temperatura máxima del agua:5˚C –35˚C
NO use la aspiradora de piscina sin un filtro rigido intacto instalados. El uso de la
aspiradora de piscina sin un filtro rigido intacto instalados ANULARÁ su garantía.
Peligro de atrapamiento por succión: Esta aspiradora de piscina genera succión.
No permita que su pelo, cuerpo o prendas sueltas entren en contacto con la