Aqua One AquaStyle 850 User manual

Instruction Manual
AquaStyle 850/980

Important Safeguards
This appliance is not intended for use by
children or infirm persons without supervi-
sion. Young children should be supervised
to ensure that they do not play with the
appliance.
Warning: To guard against injury, basic
safety precautions should be observed,
including the following:
1. Read and follow all safety instructions before
using this appliance.
2. Danger: To avoid possible electric shocks,
special care should be taken since water is
employed in the use of aquarium equipment, for
each of the following situations do not attempt
repairs yourself. Return the appliance to an
authorised service facility for service or discard the
appliance.
a) If the light falls into water, do not reach for it,
unplug it and then retrieve it. If the electrical
components of the appliance get wet, unplug the
appliance immediately (non immersible equipment
only).
b) If the aquarium shows any sign of abnormal
water leakage, immediately unplug it from the
power source.
c) Carefully examine the aquarium after installa-
tion. It should not be plugged in when there is water
on parts which are not intended to be wet.
d) Do not operate any aquarium if it has a damaged
cord or plug, or if it is malfunctioning, or dropped or
damaged in any manner.
A “drip loop” (see the diagram) should be arranged
by the user for each cord connecting an aquarium
component to a receptacle . The drip loop is the
part of the cord below the level of the receptacle or
the connector if an extension cord used. It is used
to prevent water traveling along the cord and
coming in contact with the receptacle.
If the plug or receptacle does get wet, do not
unplug the appliance. Disconnect the fuse or circuit
breaker that supplies the power to the appliance,
then unplug and examine for presence of water in
the receptacle.
3. Close supervision is necessary when the
appliance is used by or near children.
4. Always unplug the aquarium from the electri-
cal outlet; when not in use, before putting on or
taking off parts, before any type of mainte
nance, or cleaning. Never yank the cord to pull
it from the outlet. Grasp the plug and unplug to
disconnect.
5. Do not use the aquarium for reasons other
than the intended use. The use of attachments
that are not recommended or sold by the
aquarium manufacturer may cause the product
to be unsafe. This is not recommended.
6. Do not install or store the aquarium where it
will be exposed to weather or temperatures
below freezing.
7. Make sure any component mounted on a
tank is securely installed before operating it.
8. Read and observe all the important notices
on the aquarium.
9. Ensure input voltage is the same voltage as
your local power supply.
10. If an extension cord is necessary, a cord
with a proper rating should be used. Care
should be taken to arrange the cord so that it
will not be tripped or pulled.
11. A G.F.C.I (Ground fault circuit interrupter) &
surge protector is recommended for all electri-
cal appliances.
12. Ensure your hand is dry when turning the
power switch on/off and when
inserting/removing the power cord from the
receptacle.
13. If you are in any doubt about the electrical
installation or safety of this product you must
consult a qualified electrician.
For Guarantee Conditions, please refer to
the Guarantee form that is enclosed with
this product.
drip loop

Before First Use / Preparation
Read and follow all the instructions, even if you
feel you are familiar with the product and find a
place to the instructions handy for future
reference. Your attention is drawn particularly to
the sections concerning “IMPORTANT SAFE-
GUARDS” and the “WARRANTY CONDI-
TONS”. Please insure you retain your original
purchase receipt in the event that warranty
service is required.
Carefully unpack the aquarium making sure
you keep all the packing material until all the
parts of the product have been found and the
product has been assembled.
This Product is shipped to you in a factory
sealed carton. Should the Product be
damaged, dropped, malfunctions in any way,
or if the glass is damaged and requires
replacement, contact the retailer where the
product was purchased for inspection.
Know Your Tank
Spray Bar
Elbow
Power Head Adapter
Power Head
Impeller
Replacement Parts & Filter Media
Use Aqua One Genuine Spare Parts
Only. See your local Aqua One Dealer
and look for the number listed below for
the spare part you require. Alternatev-
ely you will find these numbers on the
silver label located on the product.
AR850/980 Black Sponge 4S
AR850/980 White Wool Pad 4W
AR850/980 Carbon Cartridge 4C
AR850/980 Impeller 4I
Aqua One Spare Parts
4I
Shaft
Rubber End
Intake Pipe
Strainer
Impeller Cap
Extension
Outlet

Set Up Instructions
1. Remove the Filter and Light Unit from the
Aquarium Body.
2. Take all the lids on the Filter Unit off ,
3. Remove the Spray Bar, Power Head and
Filter Trays.
4. In the second filter tray you will find the
remaining accessories required to complete the
set up of your filter system.
5. Take the Filter Trays and all filter media to
the sink. Ensure there is no detergent residue in
or around the sink,
6. Open the Ceramic Noodles and empty them
into the Filter Trays. Refer to Filter Media Set
Up Diagrams below for the correct setup of your
aquarium.
7. Run tap water thought them to remove any
dust.
DO NOT WASH IN SOAP OR DETERGENT.
8. Rinse the Black Sponge and place it on top
of the Ceramic Noodles.
9. Rinse the Carbon Cartridge and place this
on top of the Black Sponge.
Filter Media Set Up Diagrams

10. Leave the Filter Trays at the sink.
11. Slide the Power Head Adaptor into the top
of the Power Head.
12. Insure it is inserted firmly.
13. Once complete slide the Power Head into
the bottom of the Filter Unit.
14. Connect the Intake Pipe and Strainer
together.
15. Slide them into the bottom of the Power
Head.
16. Connect the Outlet and Extension
together.

17. Connect them into the bottom of the Filter
Unit.
18. Then place the Trays with the washed
media inside them in to the Filter Unit.
19. You will find the silicon elbow has a tube
inserted in it. This may need to be forced in
further, having an overall length of 15cm.
120. Connect the Spray Bar and the Elbow
together.
21. Insert the Elbow and Spray Bar into the top
of the Power Head, press down firmly ensure it
is a tight fit.
22. Push the first filter tray to the right as far as
it will go.
23. You will notice the Power Head is sitting on
an angle.
24. In order to correct this you need to slide the
0-ring on the Spray Bar along and position it so
it is resting against the edge of the first filter
tray. Do this until the Power Head is straight.

25. Place the aquarium on a flat level surface
strong enough to support its weight. We recom-
mend a genuine Aqua One Aquarium Cabinet
(sold separately) rather than general house-
hold furniture.
26. Place the Filter Unit (once complete) on
top of the Aquarium Body towards the back.
27. Wash aquarium gravel.
Place a portion of gravel
into a bucket.
28. Run water through and churn it over with
your hand until the water running out of the
bucket is clear. It is important to wash the gravel
thoroughly. Repeat this process several times
until all the gravel has been washed.
29. Place washed gravel over the base of the
Aquarium.
30. At this stage place plastic plants, decora-
tions and heater (see Tips) into the tank.

31. Fill the aquarium with tap water to the level
indicated.
32. Use Aqua One quality Water Conditioner
(sold separately) to remove harmful chemicals
from tap water. E.g. chlorine (see Tips)
33. Place the Light Unit on the front of the
Aquarium.
34. Plug in the Power Head, Light Unit and
Heater (if installed) and turn on. Refer to Impor-
tant Safety guards for set up of the Drip Loop.
35. Insure the holes of the Spray Bar are facing
down and that water is flowing through it.
36. Replace all lids on the Filter Unit.
37. Turn the light switch on ensure the lights
work.
38. Test and adjust pH levels.

39. Allow the aquarium to stand for 3 to 4 days
before the introduction of any fish.
40. Seek advice from your retailer for correct
fish numbers and species compatibility.
TIPS -
An Aqua One heater and Thermometer is
required if you are setting up a tropical or
saltwater aquarium. Refer to heater instruc-
tions for correct set up and positioning.
Chlorine and other heavy metals will harm
your fish. Aqua One water conditioner will
remove these impurities and create a safe
environment for your fish.
These products are available separately
from your local Aqua One Dealer.
Introduction of Fish
Note: is only a guide! You should seek profes-
sional advice from your aquarium specialist at
the time of purchase.
DO NOT ADD ALL FISH AT ONCE!
Build stock levels slowly over time. Allow at
least one week between additions add a filter
supplement to help the biological system cope
with the additional waste.
Do not over crowd. Remember all fish will grow,
so allow them adequate space.

Tank Maintenance
DAILY Feed your fish as per instructions on your
fish food container.
WEEKLY Test and adjust pH levels if needed
Use Aqua One quality pH test kit, available from
your local Aqua One Dealer. pH is a measure of
how acidic or alkaline the water is. It is measured
on a scale of 0-14 in which 7 is neutral, less than
7 is acidic and more than 7 is alkaline.
Some species require specific pH levels please
seek advice from your aquarium specialist.
FORTNIGHTLY 25% Water Change
What you will need: A Bucket, Gravel Cleaner,
Towel, Water Conditioner, Bio Booster and clean
hands. All items are available from your local
Aqua One Dealer.
1. Unplug the Light Unit and remove it from the
aquarium. Place it somewhere safe away from
water & where it will not be broken / damaged.
2. Turn the Power Head off.
3. The fish and plants do not need to be removed
when doing any maintenance.
4. Place the towel on the floor in front of the
aquarium to guard from water spillage.
5. Use an Aqua One 4 in 1 algae scraper and
gently scrape away any algae growing on the
glass or filter pipes.
6. Using an Aqua One Gravel Cleaner* empty
approximately 25% of the aquarium water into the
bucket. Take note of how much water is emptied.
7. Fill the bucket up with the same amount of
water that was removed from the aquarium.
8. Treat the tap water with Aqua One Water
Conditioner as per the instructions on the bottle.
9. Let the bucket sit for 10 minutes.
10. Fill the aquarium up slowly to the level
indicated. Fig 31
11. Turn the Power Head back on and ensure
that water is flowing out of the Spray Bar.
12. Test and adjust pH levels.
13. Add bio booster.
12. Replace the Light Unit.
* Refer to the instructions on the back of your
Gravel Cleaner to ensure correct use.

8. Carefully leaver the screw driver downwards.
9. This will pop one side of the Impeller Cap off
Fig 4.
10. Turn the Power Head around, repeat steps 7,
8 & 9.
9. Remove the Black Rubber End Cap. The
Shaft may also come out at the same time, if not
then pull it out.
7. Grasp the Impeller Cap and remove it from the
Impeller well Fig 5.
8. Use a double ended pipe brush to clean Impel-
ler and inside of Impeller well Fig 6.
9. Also run a pipe brush through the outlet at the
top of the Power Head.
10. Clean the Intake pipe and Strainer thoroughly.
11. Reconnect all parts and place Filter Unit back
onto the aquarium.
12. Ensure the power lead is not wet and plug it
back in.
13. Turn the power back on and check that water
is flowing though the Spray Bar.
14. Replace the Light Unit and Lids.
YEARLY
The ceramic noodles are designed to be mainte-
nance free,
NEVER RINSE THEM IN TAP WATER.
See Hints & Tips for Best Results for more
information.
WEEKLY See diagrams on next page...
1. Turn the Power Head off.
2. Remove the Lids from the Filter Unit.
3. Remove the Elbow and Spray Bar unit from
the top of the Power Head.
4. Remove the Carbon Cartridges and Black
Sponges from the Filter Unit.
5. Empty a small amount of water from the
aquarium into a bucket.
6. Rinse the Black Sponges. Discard the used
water; do not add it back into the aquarium.
7. Rinse the Carbon Cartridges out under the
tap, rinse thoroughly.
8. Re-insert the Black Sponges and Carbon
Cartridges.
9. Then connect the Elbow and Spray Bar unit
back onto the outlet at the top of the Power
Head. Make sure the holes of the Spray Bar
are pointing down onto the Carbon Cartridge
and that the end of the Spray Bar has the cap
fitted.
10. Ensure the aquarium is full. Refer to Fig 31.
11. Turn the Power Head back on and ensure
that water is flowing out of the Spray Bar.
12. Replace the Lids on the Filter Unit.
13. Add bio booster.
The carbon filter cartridge should be replaced
every 6 - 8 weeks for optimum filter perfor-
mance.
MONTHLY See diagrams on next page...
1. Turn the power off. Unplug both power leads
2. Remove the Light Unit and Place it some-
where safe away from water and where it will
not be broken / damaged.
3. Remove Filter Unit from aquarium and take
to sink and remove the lid.
4. Disconnect Spray Bar and Elbow and clean
with double ended pipe brush.
5. Slide the Power Head off the bottom of the
Filter Unit Fig 1.
6. You will need a flat head screw driver Fig 2.
7. Holding the Power Head upside down Insert
the screw driver into the larger slot of the
Power Head. Fig 3
Filter Maintenance

Filter Maintenance Diagrams
Fig 1 Fig 2
Fig 3 Fig 4
Fig 5 Fig 6

LIVE PLANTS
Once the water conditions and pH levels have
been corrected, live plants can be added to the
aquarium. Remember to empty some water
from the aquarium before adding anything to it.
REMEMBER LIVE PLANTS NEED TO BE
FED! An aquarium safe plant fertiliser should
be used.
LIGHTING
No more than 8 hours of light each day and
definitely no natural light. Longer light times will
accelerate algae growth in the aquarium and
has no benefit to plants or fish.
• Specialist light tubes are available through
retailers for saltwater and planted aquariums.
• We recommend replacing the light globe once
every twelve months based on the light being
on 8 hours a day as the spectrum of light
changes over time.
FILTER MEDIA
Biological Filtration (Ceramic Noodles)
Biological filtration is a process where toxic
nitrogen compounds such as ammonia and
nitrite (fish waste) are removed from the system
via a breakdown process carried out by nitrify-
ing bacteria. (Nitrobacter and Nitrosomonas).
These nitrifying bacteria need substrate with a
high surface area to adhere to such as
Ceramic Noodles.
• When starting a new system it is important to
remember that bacteria takes time to develop
and grow.
• You can speed up the process by ‘seeding’ the
system with commercially available bacterial
cultures / bio boosters.
• Over time this media can block up or break
down so it is important to monitor it. Seek
advice from your Aquarium Specialist if either of
these problems arise.
Mechanical/Chemical Filtration (Carbon
Cartridge)
This is the removal of dissolved organic and
inorganic substances through adsorption on a
porous substrate or by direct chemical removal.
Dissolved organic compounds are what turns
the water a yellow-brown colour or causes
foaming at the surface of the aquarium and
need to be removed.
• Remove carbon if treating fish with medica-
tion.
• Replace every 6 – 8 weeks as the carbons
absorption capacity will have depleted.
• Rinse well before placing in the aquarium. (in
tap water)
Mechanical/Biological Filtration (Filter
Sponge)
This is the process whereby suspended solids
or particulate matter are removed from the
water.
It is important to remove suspended solids not
only to improve clarity of the water but also to:
• Avoid smothering the gills with solids such that
fish cannot breathe.
• Decrease risk of disease outbreaks - there are
high numbers of bacteria associated with
organic suspended solids.
• Protect the biological filter material from
rapidly becoming clogged.
• Can also act as a biological filter medium by
providing sufficient surface area to host benefi-
cial bacteria.
Hints & Tips For Best Results

If you are in any doubt about the electrical
installation or safety of this product you
must consult a qualified electrician.
LIGHT UNIT DOES NOT WORK
1. Ensure switch is in the on position on the top
of the Light Unit.
2. Check light is plugged into power supply and
the switch is on
3. Check the globe is in good condition.
Replace if needed.
POWER HEAD WORKING BUT NO / SLOW
WATER FLOW
1. Check Impeller is in good condition and
replace if needed.
2. Make sure water level in aquarium is above
the Power Head. Please note the Power Head
is a water proof unit.
3. Clean Impeller, Power Head and all Inlet and
outlet pipes.
4. Check that the Spray Bar is inserted correctly
with the end cap at the opposite end to the
elbow.
AQUARIUM POSSIBLY LEAKING
1. Clean filter cartridge as this can create an
overflow.
2. Make sure spray bar holes are pointed down
onto the Carbon Cartridge.
3. Make sure water level is not to high Refer to
Fig 31.
4. If an air stone is being used check it is not
bubbling water over the rim of the aquarium if
so turn the air pump down.
5. Make sure the aquarium is sitting on a level
surface
6. If it is a salt water aquarium remove any salt
creep as it can drain water from the aquarium.
7a. Remove the Light Unit & Filter Unit from the
top of the aquarium. Mark the water level.
Remove any excess water that may be sitting
on the edge of the aquarium. Leave for an hour.
If water level drops proceed to step 7b.
7b. Remove the fish, decorations and gravel.
Empty the aquarium and clean the glass DO
NOT WASH IN SOAP OR DETERGENT. Place
a piece of newspaper on a flat level solid
surface. Carefully fill the aquarium ensuring not
to spill any water on to the newspaper. Leave
the aquarium for several hours and then inspect
the newspaper for wet patches.
Trouble Shooting

Precision Manufactured in the P.R.C.
Designed in Australia by Aqua One
Distributed in Australia by:
Kong's (Aust.) Pty. Limited
48 Williamson Rd. Ingleburn.
2565 NSW Australia.
Distributed in New Zealand by:
Kong's (NZ) Limited
52 Glenlyon Avenue. Greerton.
Tauranga New Zealand.
Distributed in Hong Kong by:
Kong’s Aquarium Supplies Co., Ltd
No 31, 3/F Thriving Industrial Centre
26-38 Sha Tsui Road, Tsuen Wan,
Hong Kong.
Distributed in the UK by:
Kong’s (UK) Limited,
C/O Aqua Pacific UK Ltd.
PO Box 268
Romsey Hampshire
SO51 0WW
United Kingdom.
www.aquaone.com.au
® Aqua One and Kong’s are registered trademarks.
Aquarium Model: AquaStyle 850
Dimensions: 84 x 44 x 59cm (6mm glass)
Aquarium Volume: 165L
Filter Flow Rate: 2000/hr
Light Wattage: 2 x 30in 25W 1 x 23.5in 20W
Power Requirements: 220 ~ 240V
Suitable: Coldwater, Tropical, Marine
Aquarium Model: AquaStyle 980
Dimensions: 99 x 47 x 60cm (8mm glass)
Aquarium Volume: 215L
Filter Flow Rate: 2000l/hr
Light Wattage: 2 x 36in 30W 1 x 30in 25W
Power Requirements: 220 ~ 240V
Suitable: Coldwater, Tropical, Marine
Notes

Fish keeping has never been easier...
Aqua One specialises in all of your aquarium needs.
Aqua One uses state of the art technology which results in
the most efficient and superior aquarium products.
The Aqua One range includes a wide range of curved glass
aquariums, air pumps, filters, power heads, heaters,
reflectors, under water lighting, along with fish foods,
cleaning and maintenance accessories and decorations.
Keep an eye out for these Aqua One
products at your local retailer...
www.aquaone.com.au