Aqua Quip APL 511N Manual

1
PLUG-IN TRANSFORMER – INSTALLATION INSTRUCTIONS & OWNERS MANUAL
INSTALLATION & OPERATING INSTRUCTIONS
12 VOLT 30VA
This transformer has one secondary outlet rated 30VA.
Maximum number of lights = 1
Maximum output per light = 30VA
TRANSFORMER
12 VOLT
30VA
WARNINGS
• This transformer has one (1) 30VA output. Do not connect more than one light to
the output terminal. Warranty void if circuit capacity is exceeded.
• The Transformer is suitable for Aqua-Quip Evo2, EvoMAX, EvoFG and QC Series
LED Pool Lights.
• Install to comply with AS/NZS 3000:2007 or as amended.
Please see over for Installation Instructions.
1
SINGLE
OUTLET

PLUG-IN TRANSFORMER – INSTALLATION INSTRUCTIONS & OWNERS MANUAL
INSTALLATION INSTRUCTIONS
1 Find a suitable location for the mounting of the Transformer. It should be mounted undercover and at
least 500mm off the ground.
2 Use the Template provided on this sheet to drill mounting screw holes at 93mm apart. Screws and wall
plugs are provided. Mount the transformer onto the mounting screws. See Diagram D.
3 To connect the light cable: rst remove 20mm of outer cable sheath and then bare back the two
sheathed conductors to expose 8mm of tinned copper. See Diagram A.
4 Locate the Connector, which is supplied in a plastic bag. Afx cable to the connector and tighten
screws, see Diagram B.
Align and push the connector into the receptacle on the underside of the transformer, See Diagram C.
5 Plug transformer into a 240v power point, turn pool light on to test for a maximum of 10 seconds.
Then leave pool light off until fully submerged.
2
Automatic Pool Cleaners (Australia) Pty Ltd
40 Percy Street, Auburn NSW 2144
Ph: 02 9643 8338 Fax: [phone]
www.aquaquip.com.au
COPYRIGHT AUTOMATIC POOL CLEANERS (AUSTRALIA) PTY LTD TAPL5112p_1116
93mm
Mounting Holes Template
TRANSFORMER
12 VOLT
30VA
1
SINGLE
OUTLET
20mm
93mm
8mm
Diagram A
Cable
Diagram B
Connector
Diagram D
Mounting
Tighten screws
Diagram C
Underside of transformer

1
PLUG-IN TRANSFORMER – INSTALLATION INSTRUCTIONS & OWNERS MANUAL
INSTALLATION & OPERATING INSTRUCTIONS
12 VOLT 60VA
This transformer has two secondary outlets rated 30VA.
Maximum number of lights = 2
Maximum output per light = 30VA
TRANSFORMER
12 VOLT
60VA
WARNINGS
• This transformer has two (2) 30VA outputs. Do not connect more than one light to
each output terminal. Warranty void if circuit capacity is exceeded.
• The Transformer is suitable for Aqua-Quip Evo2, EvoMAX, EvoFG and QC Series
LED Pool Lights.
• Install to comply with AS/NZS 3000:2007 or as amended.
Please see over for Installation Instructions.
2
DUAL
OUTLET

PLUG-IN TRANSFORMER – INSTALLATION INSTRUCTIONS & OWNERS MANUAL
INSTALLATION INSTRUCTIONS
1 Find a suitable location for the mounting of the Transformer. It should be mounted undercover and at
least 500mm off the ground.
2 Use the Template provided on this sheet to drill mounting screw holes at 93mm apart. Screws and wall
plugs are provided. Mount the transformer onto the mounting screws. See Diagram D.
3 To connect the light cables: rst remove 20mm of outer cable sheath and then bare back the two
sheathed conductors to expose 8mm of tinned copper. See Diagram A.
4 Locate the Connectors, which are supplied in a plastic bag. Afx each of the cables to the connectors
and tighten screws, see Diagram B.
Align and push the connectors into the receptacles on the underside of the transformer, See Diagram C.
5 Plug transformer into a 240v power point, turn pool lights on to test for a maximum of 10 seconds.
Then leave pool lights off until fully submerged.
2
Automatic Pool Cleaners (Australia) Pty Ltd
40 Percy Street, Auburn NSW 2144
Ph: 02 9643 8338 Fax: [phone]
www.aquaquip.com.au
COPYRIGHT AUTOMATIC POOL CLEANERS (AUSTRALIA) PTY LTD TAPL5122p_1116
93mm
Mounting Holes Template
TRANSFORMER
12 VOLT
60VA
2
DUAL
OUTLET
20mm
93mm
8mm
Diagram A
Cables
Diagram B
Connectors
Diagram D
Mounting
Tighten screws
Diagram C
Underside of transformer

1
PLUG-IN TRANSFORMER – INSTALLATION INSTRUCTIONS & OWNERS MANUAL
INSTALLATION & OPERATING INSTRUCTIONS
12 VOLT 120VA
This transformer has four secondary outlets rated 30VA.
Maximum number of lights = 4
Maximum output per light = 30VA
TRANSFORMER
12 VOLT
120VA
WARNINGS
• This transformer has four (4) 30VA outputs. Do not connect more than one light to
each output terminal. Warranty void if circuit capacity is exceeded.
• The Transformer is suitable for Aqua-Quip Evo2, EvoMAX, EvoFG and QC Series
LED Pool Lights.
• Install to comply with AS/NZS 3000:2007 or as amended.
Please see over for Installation Instructions.
4
QUAD
OUTLET

PLUG-IN TRANSFORMER – INSTALLATION INSTRUCTIONS & OWNERS MANUAL
INSTALLATION INSTRUCTIONS
1 Find a suitable location for the mounting of the Transformer. It should be mounted undercover and at
least 500mm off the ground.
2 Use the Template provided on this sheet to drill mounting screw holes at 93mm apart. Screws and wall
plugs are provided. Mount the transformer onto the mounting screws. See Diagram D.
3 To connect the light cables: rst remove 20mm of outer cable sheath and then bare back the two
sheathed conductors to expose 8mm of tinned copper. See Diagram A.
4 Locate the Connectors, which are supplied in a plastic bag. Afx each of the cables to the connectors
and tighten screws, see Diagram B.
Align and push the connectors into the receptacles on the underside of the transformer, See Diagram C.
5 Plug transformer into a 240v power point, turn pool lights on to test for a maximum of 10 seconds.
Then leave pool lights off until fully submerged.
2
Automatic Pool Cleaners (Australia) Pty Ltd
40 Percy Street, Auburn NSW 2144
Ph: 02 9643 8338 Fax: [phone]
www.aquaquip.com.au
COPYRIGHT AUTOMATIC POOL CLEANERS (AUSTRALIA) PTY LTD TAPL5142p_1116
93mm
Mounting Holes Template
TRANSFORMER
12 VOLT
120VA
4
QUAD
OUTLET
20mm
93mm
8mm
Diagram A
Cables
Diagram B
Connectors
Diagram D
Mounting
Tighten screws
Diagram C
Underside of transformer