Aquaglide RIDGEWAY 10 User manual

www.aquaglide.com
1
RIDGEWAY 10
Owner’s Manual
www.aquaglide.com
version 1.0 - 8.9.2023

www.aquaglide.com
2
Capacity: 2 People
Dimensions:
L- 10.0 ft (3,05 m)
W- 8.0 ft (2,44 m)
H- 4.9 ft (1,50 m)
Minimum Water Depth: 5.4 ft (1,65 m)
Included:
1x Ridgeway 10
1x Storage Wrap
1x Repair Kit
Language Translations:
English - pg. 2
Español - pg. 15
Français - pg. 28
Deutsch - pg. 41
RIDGEWAY 10

www.aquaglide.com
3
WARNINGS
Use of this product and participation in the sport involves INHERENT RISKS of SERIOUS
INJURY or DEATH. User ASSUMES ALL RISK of injury or death.
• ALWAYS wear a properly tted USCG type III / Level 70N, ISO/CE or other agency approved
Life Jacket or Personal Flotation Device (PFD) as required in area of use.
• NEVER use while under the inuence of alcohol or drugs.
• NEVER leave children unattended. ONLY use under competent adult supervision.
• Not intended for use by children under 5 years of age.
• NEVER place wrists or feet through handles.
• NEVER use in water less than the specied minimum depth for this product.
• NEVER use with less than the specied minimum safe distance away of watercraft, shore,
docks, pilings, or other obstacles.
• NEVER swim under this product.
• NEVER dive from this product.
• NEVER exceed the manufacturer’s recommended number of users for this product.
• NEVER add any hardware or other attachments not otherwise supplied by the manufacturer.
• This product is not a personal otation device.
• ALWAYS read User’s Manual before use.
CAUTIONS
This user’s Manual is intended to alert you to some of the potentially dangerous conditions that
can arise in the use of this product. Other, unforeseen risks may exist, so always use caution
and common sense. Please contact the dealer or manufacturer of this product if you have any
questions about proper assembly, operation, or safe use of this product.
• Always read this user’s manual carefully before use and follow the instructions.
• Always limit use to swimmers only. This item provides no protection against drowning.
• Always be aware of potential dangers in the surrounding environment.
• Always take all reasonable precautions in using this product and instruct all users about safe
guidelines prior to use.
• Always maintain at least the specied minimum safe distance away from pool edge, boats,
docks, or other hard obstructions.
• Always maintain adequate vertical clearance above this item, particularly when used in indoor
pools.
WARNINGS & CAUTIONS
STOP! READ THIS OWNER’S MANUAL CAREFULLY
BEFORE USING THIS PRODUCT!
It is the owner’s responsibility to read the user’s manual and instruct all users in the safe operation of
these products. This Owner’s Manual is intended to alert you to some of the potentially dangerous
conditions that can arise in the use of this product.

www.aquaglide.com
4
• Always inate each air chamber to the specied working pressure before use. Under-ination
can cause injury due to instability.
• Always ensure connections are tight and that there is no gap between items.
• Regularly check mooring lines and connecting straps. Always replace any portion showing
signs of wear.
• Never use without proper anchoring and adequate minimum water depth for this product.
• Never exceed the maximum weight or user capacity stated for this product.
• Always evenly distribute weight from users or gear to prevent possible capsize.
• Never attempt somersaults while using this item. Head and/ or neck injuries can cause serious
injury, paralysis, or death.
• Never follow other climbers – an accidental fall may cause collision.
• Never follow others immediately into the water – wait until water is clear.
• Always remove personal items such as rings, watches or other sharp objects before use.
• Never use at night, in low-light, or in other adverse conditions.
• Never use in recreational pools. Supervised use in public or commercial pools is acceptable.
• Always secure the product when not in use to prevent access by any other users.
• Always ensure correct anchoring of the product prior to use.
• Always lubricate products with continual water ow or other suitable methods to limit risk of
skin burns. Be aware that friction may cause skin burns when attempting to slide.
AQUAPARK DISCLAIMER
The safety of our customers and their guests is our highest priority. Careful thought goes into the
design of our aquapark components, connection points and congurations to assure maximum
safety and enjoyment. Consequently, Aquaglide Lakefront and Aquapark products are not
authorized for use in combination with products or attachments from any other manufacturer.
Aquaglide product combinations must be authorized or approved in advance by the manufacturer.
Use of Aquaglide products in combination with products from any other manufacturer and/
or product arrangements not previously approved by Aquaglide may result in increased risk of
entrapment, injury, or death.
SALTWATER WARNING
Prolonged exposure to salt water can damage and/or shorten the expected lifetime of this product.
The marine environment includes many damaging elements including corrosion, abrasion, and
damage from marine life such as barnacles. Regular cleaning and rinsing with fresh water can
reduce these risks. A PVC-safe anti-fouling paint should be used to help protect this product
against marine growth. Damage caused by exposure to salt water is not covered by warranty.

www.aquaglide.com
5
Compliant with ISO 25649: 2017 -1, -2, -6, Class D
REACH, ASTM F/24
100%
122cm
213cm
max.
1,65m (5.4ft)
3,0m
(10ft)
181 kg
(400 lbs)
2 2
RIDGEWAY 10

www.aquaglide.com
6
Inatable Products – Aquaglide makes some of the highest quality inatable products in the world.
With proper care and maintenance, our products are expected to last for years under normal use. We list
important tips and instructions below. If unsure about any point, please reach us through our website at
Aquaglide.com/contact-us.
Note: see Anchoring instructions (below) before inating this item. Strong winds can make it difcult to
control this product. Be aware of weather conditions before installation.
Air Pump - Use an air pump recommended for inating your product. For products this size, use of
a high-volume electrical pump is best. Air pressure requirements are low – 5.0psi (0,35bar) or less. Air
compressors designed for high-pressure ination are not recommended because they can easily lead to
over-ination.
Valve(s) – This product uses Halkey Roberts – type (HR) valves. Valve attaches to
product using a threaded backing plate making it easily replaceable in the unlikely
event of damage.
Access valve using a coin or at tool to twist the tamper-resistant cap counter-clock-
wise. To close, insert the cap and twist clockwise using the same
tool. Note: cap is the secondary air seal. See A.
To inate, an air pump with Halkey Roberts – type (HR) valve tting is
required. Insert tting into valve and twist clockwise to lock in place.
See B.
Valve Operation: To operate Halkey Roberts – type (HR) valve,
press plunger and turn 90 degrees to set valve for inate and product
use (plunger out = 1-way airow). Press plunger and turn 90 degrees
to deate (plunger in = 2-way airow). Note: valve is primary air seal.
After ination, close with cap for secondary seal. See C.
Pressure Release Valve: Product is tted with a pressure release valve (PRV) in
critical chamber(s) to help provide catastrophic protection against damage caused
by over-ination. It is still necessary to check and regulate air pressure to maintain
proper working pressure levels. PRV has a unique setting specied to release above,
and to close near working pressure. PRV attaches to product using a threaded
backing plate, making it easily serviceable. See D.
Proper Working Pressure for each chamber is listed below. Do not overll or underll. Excessive pressure
can cause damage to the product and may void the warranty. Do not use without adequate air pressure.
Product can become unstable if underlled and may not support indicated capacity. Use a pressure gauge
(manometer) to carefully monitor air pressure in the product especially during hot or cool periods.
A
Inate (1-way) Deate (2-way)
C
B
D
ASSEMBLY

www.aquaglide.com
7
Chart 1 – Working Pressure by Chamber - RIDGEWAY 10
1. Locate a at, dry area with access to outlet for electrical pump. The best setup position will also make
launching easy. Never drag product as damage may occur.
2. Unfold product completely and locate Main Valve [1]. To help future storage, closely note original folding &
packaging method. Remove valve cap and conrm valve is in inate (1-way airow) position.
3. Insert air pump hose with proper valve tting into Main Valve [1], lock into place. Use pump to inate Main
Valve [1] to Working Pressure as shown in Chart 1.
4. Conrm that suitable anchor(s) and mooring lines are in place before launching this item (see Anchoring).
5. To launch product, lift completely and place in water. Large items may require many extra people to
accomplish this. Never drag product as damage may occur.
6. When connecting multiple items together, always follow manufacturer’s recommendations. Use only
Aquaglide Two-Step Vario-lock cinch straps and connecting rings. Make sure connection is tight and there is
NO GAP between items. Failure to connect items properly may result in injury or death. See E1 - E6.
a. Attach straps to ‘Boarding Features’ (example: Swimstep, Splashmat, Speedway, Breezeway or Deck)
where a connection is required. Boarding Features should not be attached to other Boarding Features.
b. Use all available rings to make connection. Standard connections use 5 rings. Some items use 3 or
occasionally 7 rings/ straps. RIDGEWAY 10 is a Track Feature item with 5-ring connections on 2 ends.
c. Float ‘Boarding Feature’ into desired position. Note: a matching set of connecting rings is required on
feature item.
d. Attach center strap to center ring on feature item. Connect loosely, then work outward until all straps are
connected.
e. Dive beneath to tighten all straps securely. Dive mask and several attempts may be required.
Valve [Inate Order] Working Pressure in psi (Bar)
MAIN [1] 1.2psi (0,083 bar)
E-1
E-4 E-5 E-6
E-2 E-3
Connecting Strap instructions

www.aquaglide.com
8
Proper anchoring is essential to the safety and performance of this product. We recommend using Aquaglide
mooring lines and weight recommendations as a starting point. Weight recommendations are intended to
keep products in place during a normal range of weather conditions faced by most aquaparks. Even in so-
called light-wind areas, storms, squalls and other extreme weather events can happen quickly. If improperly
anchored, product can move and/or oat away. Aquaglide is not responsible for damage, injury or loss due to
improper anchoring.
Open Water: (General guidelines - not intended to replace need for professional installation)
1. Place product in an area protected from wind and boat trafc. Conrm allowances for stated minimum
water depth, safe distance away from hard objects and vertical clearance requirements.
2. Consider prevailing conditions such as wind, waves and other environmental factors in positioning this
item. Inatable items can be unstable in strong winds. Slide faces are best positioned toward a breeze, not
across it. Check water and seabed for sharp or dangerous objects.
3. Keep product a safe distance from docks, boats, boat lifts, and any other structures. To prevent potential
damage to product, injury or death, NEVER tie the product to a dock.
4. Use one vertical mooring line for each anchor ring with an appropriate weight anchor, ground screw, or
earth anchor at base. For exposed anchorages or water depth greater than 20ft. (6m), bridles connecting two
rings to one mooring line may be preferable.
5. Anchor weight recommendations are based on the maximum potential wind loads generated by each
item at a wind speed of 26 knots (48 km/h, 30 mph). Weight recommendations are based on the apparent
weight of concrete mooring blocks in either salt or fresh water. If signicantly stronger winds are forecast, we
recommend partially deating larger items or removing items from the water for storage.Sites with potential
for extreme weather, strong tides, currents, winds and/ or swell should consider using up to 50% additional
weight or holding power.
6. Install anchors and mooring lines before inating this product.
Commercial Pool:
1. Product placement in commercial pool should be checked carefully in advance to conrm allowances for
the stated minimum water depth, safe distance away from hard objects (pool edge) and vertical clearance
requirements. Most residential pools cannot meet these requirements.
2. Pool moorings typically use a minimum of 4 horizontal mooring lines made from heavy duty elastic. Addi-
tional horizontal moorings should be added to increase stability and as necessary for larger product groups.
3. Horizontal Moorings are usually attached to pool anchor eyes, such as those used to secure lane buoy
lines. Adjust mooring lines to keep product(s) under tension at all times.
ANCHORINGANCHORING
Anchor Details – Ridgeway 10 Qty/ Weight lb (kg)
Anchor rings on product 4
Recommended anchor qty 4
2-Way Bridle? No
Recommended weight/ anchor 250lb (100kg)
Recommended total anchor weight 1000lb (400kg)

www.aquaglide.com
9
Ridgeway 10 is a oating climbing activity for use in water. Users climb onto the top portion to traverse the
item using the hand and footholds provided. Users may jump into the water from several juping stations, or
use hand and footholds to climb down the other side.
Never gather beneath Climbing Walls while someone is climbing. Always make sure water is clear before
jumping.
PVC surfaces are more slippery when wet, which can lead to loss of balance when walking or climbing. Slid-
ing surfaces will work best when wetted rst. Chemical treatments are available to reduce friction on sliding
surfaces, but are generally not necessary if products are kept clean.
Maintain working pressure: Air pressure depends on temperature. Always conrm proper working pres-
sure before and during use, as temperature changes may affect internal pressure. If the product shows signs
of instability or loss of pressure, discontinue use until the product returns to working pressure and/or repairs
are made.
Spread loads: Do not concentrate more than 300 lbs (136 kg) in one area during use.
Manage Winds/Thunderstorms: If strong winds (25 knots+) or thunderstorms are forecast, discontinue
use. Remove the product from the water and secure or store it.
Check connections: Check regularly to conrm that all connections are secure. Replace connecting straps
that show signs of wear.
Clean and maintain: Check regularly that the product is clean and that all handles and accessories work
properly. Each site requires its own cleaning/maintenance schedule, but regular cleaning and periodic main-
tenance is necessary to ensure the full life of the product. Replace handles or accessories that show signs of
wear.
Check moorings: Regularly check mooring lines and anchors, especially after extreme conditions. Replace
any item showing signs of permanent wear or stretching.
OPERATION

www.aquaglide.com
10
Proper cleaning, maintenance, and storage is essential to help prolong the life of your product. Do not use
petroleum-based cleaners on this product. Improper use of a pressure washer can damage or destroy the
product.
Basic Cleaning: Use soft bristly brush or sponge with mild soap and fresh water.
Difcult Cleaning: For heavy stains, marine growth, algae, mold, dirt and oils check with your distributor, or
on our website, Aquaglide.com for commercial-grade cleaning solutions. In general, be sure that any cleaning
products are clearly labeled as safe for PVC.
UV Protectant: Long-term exposure to sunlight will reduce product life and can damage the product.
Regularly apply a UV protectant to exposed surfaces to ensure the life of your product. The best time to begin
applying UV protectant is when the item is clean and new. Repeat applications depend on site specics. In
temperate climates, apply 1-2 times per year. In tropical climates, monthly application is not uncommon. Find
more information on professional-grade UV protectants from your distributor, or at Aquaglide.com.
Replacement parts: Items like valves, PRV’s, handles, rings and other accessories can occasionally wear
out and need replacement to maintain the full function of your product. Check with your distributor, or on our
website, Aquaglide.com for available parts and replacement instructions.
STORAGE - Clean, Protect, Dry: Clean product and consider applying UV protectant before storage. UV
protectant conditions the PVC material and will help protect against dirt accumulation during storage. Conrm
product is completely dry before folding.
Deate & Fold: Deate product completely: Consider using electric pump in ‘deate’ mode. Close valve to
prevent air return. Fold deated product in similar manner to original packaging. If uncertain, fold in thirds,
then roll loosely toward the valve(s). Enclose product in original storage wrap, if included.
Storage: Store the product out of direct sunlight and protect from environment in a clean, dry location such
as a sealed closet, crate or container to prevent against serious threat of rodent damage. When building or
sourcing storage container, use original box dimensions as a baseline. Size up by at least 15-20% to allow for
imperfect folding. Never store in a damp location or at temperatures below 40 F (4 C).
CARE AND MAINTENANCE