AquaIOT Aquaeegg User manual

01
What’s Included
Aquaeegg Device Charging Cable Waterproof Plugs Tether

02
1. Get the App
Download the AquaIOT app for your smart phone by scanning this QR code or search AquaIOT in the app
store.

-ON
-OFF
03
-OFF
-ON
-OFF
-ON
-ON
-OFF
2. Turn on Sensor
a. Remove the Aquaeegg from the box and confirm the black mark on the sensor is aligned with the "OFF" position
(as shown below, left).
b. Rotate the sensor clockwise by 45° and align the black mark on the sensor with the "ON" position (as shown
below, right).Then the Aquaeegg is turned on shining.

04
-OFF
-ON
3. Charge your Aquaeegg
Use the charging cable to connect Aquaeegg device and USB power port.Pay attention to the protruding surface of
the charging cable is on the outer flank. During charging, the Aquaeegg flashes red light. The green light flashes
when charging is completed (Aquaeegg can be charged in ON or OFF state).
NOTE: After charging, the sensor cover and the charging port plug MUST be in place for accurate reading.

05
4. Attach the tether wire (optional)
a. Secure the sensor of Aquaeegg with a fixed coil, please ensure that the rope loop does not slip off.
b. Tie the other end of the tether to some objects on the shore,preventing Aquaeegg from drifting away.Use tether
wire to fetch Aquabot when needed.
An optional holding fixture can be purchased
on Aqua-bot.com to attach Aquaeegg to the
pool wall to prevent it from drifting around.

06
5. Release Aquaeegg to Water
Importantly, first insert the waterproof cover into the charging port before the Aquaeegg is put into the water.
Tilt the Aquaeegg for 45-degree with the gas outlet of the sensor facing up (as shown below), and slowly place it
into water or pool, to avoid trapping air bubbles inside the sensor. Slowly shake a few times in water to release air
bubble if necessary.
Trick: You can soak the whole Aquaeegg a few inches below the water surface to utilize water pressure to drive out
the air bubbles out of the sensor compartment much easier.
NOTE:Do NOT put unassembled Aquaeegg device without sensor directly into the water.It will cause damage to the
circuit board.

07
6. Connect Aquaeegg
a. Make sure your phone is within a range of 50 meters to the Aquaeegg and Bluetooth is ON.
b. Start the AquaIOT APP on your phone.It will automatically search and connect Aquaeegg device.The message of
“Connection Successful”will show on the screen if Aquaeegg connection is successful.If the connection fails, please
restart AquaIOT and connect it again.

08
7. Activate Aquaeegg Sensor
a.When Aquaeegg is used for the first time or reuse after a long time, please activate Aquaeegg on App (Aquaeegg
will automatically analyze the test environment and complete calibration).The calibration method is shown below.
b. Click the "Calibration" button in App settings, the Aquaeegg will flash blue light, which takes about 10 minutes.

09
You’re Done!
Congratulations! Your Aquaeegg has been set up and ready to go.
Srcoll down the screen
the App displays the water
quality data of the hourly
automatic tests between
9: 00am and 5: 00pm by
default (this time period
can be set in the App).
To query the historical
data, click Data icon at
the bottom right
corner of the screen.
,

10
You Can Set Light Modes!
You can set the light mode in the menu by scrolling the screen right.
Mode 1- Lights Up: LED is always on and changes color according to water
quality. Red indicates poor water quality. Green indicates good water quality.
Yellow indicates fair water quality.This mode uses power quickly. Fully charged
device lasts for about 2 days in this mode.
Mode 2 - Tinkle: LED flashes periodically to indicate water quality. Fully charged
device lasts for about 3 days.
Mode 3 - Rainbow: LED flashes with rainbow color.This mode is good for party,
but burns power quickly. Fully charged device lasts for about 1 day.
Mode 4 - Power Saving: LED turns off to save power. Device goes to sleep while
not sensing. Fully charged device can last for about 30 days.

11
Enter Pool Volume to Get Chemical Recommendations
You need to enter the amount of water in your pool in our app settings interface so that the APP can provide
recommendations for chemical dosage.

-OFF
-ON
12
O-rings
-ON
-OFF
Replace Sensor
a. Rotate the sensor to the replacement position as shown below in the picture on the left, and remove the sensor.
b. Get the new sensor from the box. Confirm the two red O-rings in place as shown below. Do NOT use without O-rings.
c. Align the top of the sensor module with Aquaeegg plug-in hole.Pay attention to align the small protrusion on the sensor
to the alignment nut on the Aquaeegg device.Then press in and hold the sensor module, and rotate it clock- wise for 90
degree until no further rotation can be made. Aquaeegg will flash red, green, blue colors alternately to indicate successful
installation.

13
Quick Tips:
1. Please do NOT put Aquaeegg close to inlet/outlet of pool or other electronics
such as pump, heater, or cleaning robot. Find a calm area for Aquaeegg to avoid
water turbulence to interfere testing.
2. Aquaeegg is a monitor, not a test meter, as it tests hourly automatically. Please
do not use Aquaeegg to test liquids other than pool water, as liquids like coffee,
beer, and beverage would contaminate the sensor.
3. The sensor cover and the charging port plug MUST be in place for accurate
reading.
4. When your phone is disconnected with Aquaeegg,it still tests water according
to the default time point. Once the connection is restored, Aquaeegg will send
the data to the phone,which can be viewed in AquaIOT's "Data" page.
5. When App reminds that the sensor module needs to be replaced, please
replace it as described on page 12. The sensor can be purchased at www.
Aqua-bot.com.
6. When the Aquaeegg 's lights are no longer flashing or power bar on the APP
screen is low, you need to recharge the Aquaeegg device. Fetch the Aquaeegg
from the water, and use paper towel to wipe the surface and let it dry.
7. When Aquaeegg is used for the first time or used after being idle for a long
time, Aquaeegg needs to be calibrated at the App client, which takes about 10
minutes. Please refer to page 8 for specific steps.

14
Water Quality Guide
For water quality of swimming pool
NOTE: This data table is partially based on some publications about water quality. It only serves as a reference. Please consult your pool
technician for your specific types of pool before action. AQUABOT INC. is not responsible for how you use the measured data.
Illustration of
light colour
pH（Acidity and
alkalinity）
ORP
（Oxidation-
Reduction
Potential）
Green indicates
good water quality
respectively
7.2≤pH≤7.8
7.0≤pH＜7.2
7.8＜pH≤8.0
≥650mV 0≤TDS≤2000ppm
2000＜TDS≤2500ppm
＞2500ppm
600≤ORP＜650mV
＜600mV
Yellow indicates
fair water quality
respectively
Red indicates
poor water quality
respectively
RC
(Residue
Chlorine)
1≤RC≤3ppm
0.5≤RC＜1ppm
3＜RC≤4ppm
＜0.5,
or
＞4.0
＜20,
or
＞31
TDS
（Total dissolved solids）
Temperature
（℃）
23≤T≤28
20≤T＜23
28＜T≤31
＜7.0,
or
＞8.0

0-7 ±0.3 or 10%
4-10 ±0.3
0-2000 ±10%
±10%0-1000
15-30 1
15
Product Specification
Product Specification
Wireless communication Bluetooth4.2 ( Bluetooth Low Energy )
Wireless range 50 meters (outdoor)
Dimensions( HxD ) 100 *84 mm
Test Environment
Safe Environment
Sunshade, room temperature, keep ventilation, dry.
Characteristics Range Precision
Residual chlorine(ppm)
pH
TDS(ppm)
ORP(mV)
T(℃)
Swimming pool(mainly for pool using clorine/bromine chemicals.Please note that
salt pool may reduce lifetime of sensor due to severe erosion)

16
Important Safety and Compliance Information
To reduce the risk of injury and damage, keep these safety precautions in mind when setting up, using and maintaining Aquabot.
· Read all operating and safety instructions before operating Aquaeegg.
· Retain this user’s manual for future reference.
· Do NOT use this device to test hot water.The operation temperature range is 15~30 deg.C.
· Do NOT drop this product from a high place. If the product is found cracked, it cannot be placed in water.
· Although Aquaeegg is a fun device, it is a tool, not a toy. Do NOT throw the product into water.
· Do NOT place Aquaeegg into water without sensor.
· Wipe the charging port on the Aquaeegg to dry before charging.
· To ensure the test accuracy, the sensor needs to be replaced every six months
(the specific time depends on the operational environment).
· Do NOT step on,drop, or knock on this product.
· Do NOT disassemble or modify this product and the sensor.
· Do NOT perform operations not described in this manual.
· To avoid the possibility of accidental ingestion, keep the product away from young children.
This product is an engineering design of radio station equipment with small radio wave data communication system. Aquaeegg
operates in the 2.4GHz band. It may affect other devices using the same frequency for communication. Before using this product,
please confirm whether you have used other radio stations nearby. In the event of radio interference between this product and“other
radio stations”, please change the place of use or stop using other devices.
Under normal use according to the user’s manual, if there is a failure during the warranty period, please send email to
[email protected], and the company will reply to you regarding the return process.
We do not provide sensor modules for free that need to be replaced due to normal aging. Please purchase them at dealer’s website or
company’s website.
Regardless of whether it is during the warranty period, Aquabot is not responsible for any damage or injury caused by using the
product. Aquabot only bears the compensation up to the product payment limit.

17
FCC WARNING
This device complies with part 15 of the FCC Rules.Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.To maintain compliance with FCC’s RF Exposure guidelines,
This equipment should be installed and operated with minimum 20cm distance between the radiator your body: Use only the
supplied antenna.
Regardless of whether it is during the warranty period,Aquaeegg is not responsible for any damage or injury caused by using the
product. Aquaeegg only bears the compensation up to the product payment limit.