AQUAS INDULGE TOUCH INLINE X JET User manual

These instructions contain all the necessary fitting and operating instructions for your electric shower.
Care taken during the installation will provide a long, trouble free life from your shower.
INDULGE TOUCH
FLEX SMART
9.5 KW
INSTRUCTION GUIDE AND USER MANUAL
INSTANTANEOUS ELECTRIC WATER HEATER - INDULGE TOUCH
By AQUABELLA SHOWER CO.,LTD.
INDULGE TOUCH
INLINE X JET
9.5 KW

PLEASE READ THIS IMPORTANT SAFETY INFORMATION

IMPORTANT

BATHROOM
FLOOR
CEILING JOISTS
SPILL
OVER
LEVEL
HOSE
RETAINING
RING
DOUBLE POLE SWITCH CEILING MOUNTED
GENERAL LAYOUT OF A SHOWER INSTALLATION

RECOMMENDED INSTALLATION DIMENSIONS
INDULGE TOUCH INLINE 9.5 KW. INDULGE TOUCH FLEX 9.5 KW.

No.
1A
1B
2
3
3A
3B
4
5
6
7
8
9A
9B
10A
10B
11
12
AQUAS CODE
AS02001CP
AS02086CP
AS06003
AS07018CP
AS07008CP
AS07009CP
AS10001CP
AS05012CP6
AS05015CP
AS09002CP
AS06040CP
AS03076CP
AS03146CP
AS50001FC
AS50001MB
AS50003
DESCRIPTION
OVERHEAD - SMART 200 - NO AIR CHROME
OVERHEAD X JET 200 CHROME
2.5mm SEALING WASHER FOR SHOWER HOSE - PACK 5
TOP CONNECTER FOR SHOWER ARM
NON ROTATION SHOWER ARM AND HEATER CONNECTOR
NON ROTATION SHOWER ARM AND HEATER CONNECTOR
FREE FIX WALL BRACKET SET CW FIXINGS
WALL BRACKET PACK FOR SLIDE BAR X 2 ( FREE FIX ) CHROME
SHOWER TUBE 600 X 25MM WITH END CAPS CHROME
FRONT LOADING SLIDER MECHANISM CHROME
SMOOTH 1.5M PVC SHINY HOSE WITH ABS CONICAL NUTS CHROME
HAND SHOWER BELLA 3F - NO AIR CHROME
HAND SHOWER X JET 1F CHROME
HEATER COVER COMPLETE 2 HANDLE FULL CHROME
HEATER COVER COMPLETE 2 HANDLE MATT BLACK
SCREW FIXATION PACK FOR HEATER
INLINE SLIDE BAR CHOME
SPARE PART DETAILS FOR INDULGE TOUCH WATER HEATERS

8
INDULGE TOUCH INLINE 9.5 KW MANUAL WATER HEATERS
1B
3B
2
3A
1A
4
4
2
11
11
11
11
10
10
4
4
4
4
4
4
7
4
4
12
2
2
3
9A
2
9B

INDULGE TOUCH FLEX 9.5 KW MANUAL WATER HEATERS
1B
3B
2
3A
1A
4
4
2
9A
11
11
11
11
10
10
5
5
5
4
4
4
4
2
2
8
6
6
6
7
5
5
5
5
5
2
3
9B

for INDULGE TOUCH INLINE MODELS
ASSEMBLY OF UPPER SHOWERING COMPONENTS

for INDULGE TOUCH INLINE MODELS
ASSEMBLY OF UPPER SHOWERING COMPONENTS

for INDULGE TOUCH FLEX MODELS
ASSEMBLY OF UPPER SHOWERING COMPONENTS

Top fixing position
arrow depict water and
electrical entry points.
PLUMBLING CONNECTIONS

.
Page 13

ELECTRICAL CONNECTIONS

ELECTRICAL WIRING DIAGRAM
1.Thermal cut-out
2. Power PCB
3. Solenoid valve
4.Temperature sensor
5. Pressure switch
6. Control PCB

FITTING THE BACK COVER INTO POSITION
DIVERTOR HANDLE ( UPPER HANDLE )
VOLUME CONTROL HANDLE ( LOWER HANDLE )
Make sure that the Divertor spindle and the raised button on the divertor handle are in the
12 O'clock position before fitting the cover.
Turn the stabilizer valve spindle and volume handle fully clockwise until resistance is felt.
NOTE: Refit digital supply cable and fit cover. refit 2 cover fixing screws.
Stabilizer valve
Divertor spindle
When fitting the cover, it is important to align the divertor spindle and
volume control spindle inside the heater.

COMMISSIONING THE SHOWER
1. Make sure that the electrical supply has been isolated at the double pole isolating switch.
2. Turn the divertor handle to the left position (Button at 9 O’clock for hand-shower function)
(Button at 3 O’Clock for Overhead position).
3. Turn the volume handle fully anticlockwise to the maximum volume position.
4. Ensure that the water supply is fully on at the mains stop cock and isolating service valve.
5. Switch on the electrical supply at the double pole switch.
The Aquas digital heater has 3 settings and automatically defaults to the COLD ONLY setting.
6. Press the On / Off Button. This action will activate the internal solenoid valve
and start the water flowing at maximum volume.
7. Press the Middle Digital button with the MINUS Symbol …Once Lit , .this will activate the heater
to deliver warm water up to a max heating capacity of 5.0 KW power (Summer Setting)
8. Press the Higher Digital button with 2 MINUS Symbols …Once Lit , .this will activate the heater to
deliver maximum hot water with a maximum heating capacity of 9.5 KW power (Winter Setting)
9. Rotate the volume handle at setting step. NOTE …as you lower the flow rate ,
the warmer the outlet temperature of the water will become.
10. Push the On / Off button to stop the water flow from the heater …
The Aquas heater is preset to a COLD START MODE….see below important note.
11. Switch off pull cord or wall mounted switch.
12. Remove the hand-shower and overhead to make sure they are not blocked with debris from
the water. If necessary clean and refit.
13. Remove the filter and clean out any debris from the residual pipework.
Clean and refit - For the Filter Removal see section on maintenance.
IMPORTANT NOTE
If the outlet temperature is lower than 55 degree: after turning off the shower heater,
water will still flow out for 6 seconds to reduce residual heat in the water tank,
designed as a safety feature to protect the next user.

OPERATING THE SHOWER
1. Switch on electrical supply - pull cord or wall mounted switch
The COLD WATER only feature button will light up.
2. Press the ON / Off Button to start the flow of water.
3. Select your shower mode setting -
your Aquas Heater comes with 3 settings.
a) COLD WATER ONLY
b) ECO HEAT setting.
( 50% - summer setting )
wait for 3 to 5 seconds for
the warm water to arrive.
c) MAX HEAT setting
( 100% Winter Setting )
wait for 3 to 5 seconds or
the hot water to arrive.
4. Turn the divertor handle
to select the showering
function you require
Left for Hand-shower –
Right for Overhead.
5. When turning the Volume
Control Handle, this will change
slightly the output temperature of the water.
6. To turn off the shower unit , press the ON / OFF button.
7. Your Aquas shower is fitted with an automatic Phased shutdown which flushes any remaining
hot water out of the unit for safe continued operation.
Therefore Hot water will continue to flow for a few seconds when turned off.
If the temperature of the water is above 55 degrees , the unit will continue to flow for 12 seconds.
If the temperature of the water is lower than 55 degrees , the unit will continue to flow for 6 seconds.
IMPORTANT NOTE
The Higher the flow the temperature will decrease.
The Lower the flow the temperature will increase.
COLD WATER ONLY SETTING
ECO HEAT SETTING (SUMMER)
DIVERTOR HANDLE
HAND-SHOWER
OR OVERHEAD FUNCTION
VOLUME CONTROL HANDLE
ON / OFF BUTTON
MAXIMUM HEAT SETTING (WINTER)

MAINTENANCE – CLEANING THE FILTER
STEP 1
Remove front cover assembly, loosen these two screws, the decor cover can be removed.
STEP 2
STEP 3
Use flat-head screw driver to remove filter, clean it, and refit.
Clean the filter and refit.
FILTER

2. If scale deposits are stubborn,
Soak the shower-head or hand-shower
in a proprietary Limescale remover and
rinse thoroughly before use.
Your AQUAS Branded heaters are supplied by Aquabella Shower Co.,Ltd. in Thailand.
For information or service assistance , please contact the installer or the local
UK distributor from where the heater was purchased.
AI0062
1. To break away scale deposite on a daily
basis simply rub your thumb over the surface
whilst the shower is running.
SHOWERHEAD CLEANING INSTRUCTIONS