Coram Showers OFFSET QUADRANT User manual

71680 00 / Issue 3 / 14
CUSTOMER CARELINE 01746 713410
Equipment needed:
Drill, 6.5mm Masonry Bit, 4.5mm & 3mm Metal Bits (general), Crosshead Screwdriver, 16mm Spanner, Spirit Level, Pencil,
Tape Measure, Masking Tape, Silicone Sealant.
Note: The screws and wall plugs supplied are for masonry walls. For lightweight walls i.e. stud partition, plasterboard etc,
use the correct type of fixings.
Please read these instructions carefully and keep for future reference.
Incorrect fitting will invalidate the guarantee.
SAFETY
●Handle glass with great care.
Although the glass is very tough, sharp impacts can damage both the glass and metal frame.
●Make sure there are no hidden pipes or cables hidden in the wall where you intend to drill.
●Wear safety goggles, shoes and appropriate clothing.
BEFORE INSTALLATION
●Check that the shower tray is level in all directions. The enclosure will not sit correctly on an uneven surface.
If uneven, the wall channels may not fit and the doors may not shut correctly.
●The enclosure should be fitted on tiled walls which are sealed with waterproof grout.
●There must be a good silicone seal between the rim of the shower tray and the wall.
●The shower tray and the enclosure must match in size. Attempting to fit the incorrect size of enclosure to
the shower tray will result in water leaks.
●Always check very carefully that components are vertical.
●To avoid damage, use the opened out packaging to build the enclosure on.
PREMIER QUADRANT / OFFSET
QUADRANT

2
a: Drill holes in both wall channels at the points shown (in the groove) using a 4.5mm drill bit.
b: Ensure the shower tray is level in all directions.
IMPORTANT: Clean the tray and seal the gap between the tray surface and tiles. It is important that the tray is sealed right up to
the tray edge so that the bottom of the wall channel is sealed. Failure to do this will cause water to leak under the wall channel
and between the tray and tiles, resulting in damp patches on the wall and under the tray.
1a b
PN11029
800 RAIL - PN80605
900 RAIL - PN80606
PN11029
800 RAIL - PN80605
900 RAIL - PN80606
PN11029 PN11029
1000 x 800 RAIL - PN80607
1200 x 800 RAIL - PN80609
1200 x 900 RAIL - PN80611
1000 x 800 RAIL - PN80608
1200 x 800 RAIL - PN80610
1200 x 900 RAIL - PN80612
800 =
PN40267
900 =
PN40272
1000 =
PN40261
1200 =
PN40263
Check contents of pack before installation. If anything is missing, contact our Customer Careline for assistance.
CUSTOMER CARELINE: 01746 713410
8
PN3230
8
PN3225
32mm
2
6
4
2
PN60093
12mm
2/4
PN50359
PN40308
PN60014
13mm 1
2
1
PN80564
PN60162
PN40275
2
4
4
PN60220
PN4745
6
PN50370
PN80618
8
PN3222
10mm
PN
11031
100mm
max
=
=
=
100mm
max
ø 4.5
mm
PN
11031
PN
11031
PN
11031
PN60490
8

3
3
a: Place the wall channels on the tray ensuring they are vertical and an equal distance back from the front of the tray.
Place masking tape against the wall before marking drill hole positions, this will help prevent the drill bit slipping. Drill 6.5mm
holes, 30mm deep and insert the wall plugs. b: Apply sealant to the back of the wall channels and around the fixing holes.
c: Fix the wall channels to the walls using 8 x 32mm screws.
a b c
2
The Offset Quadrant can be assembled with the offset on either the right or left.
Note: The following instructions show installation of the Quadrant.
a: Place the bottom rail onto the tray with its end mouldings inserted into the wall channels.
b: Centre the bottom rail between the wall channels so that there is an equal gap at each end.
4a b
==
X
X = Door widths
800 = 780 - 805mm
900 = 880 - 905mm
X
Y = Widths
1000 x 800 = 780 - 805mm
1200 x 800 = 780 - 805mm
1200 x 900 = 880 - 905mm
X = Widths
1000 x 800 = 980 - 1005mm
1200 x 800 = 1180 - 1205mm
1200 x 900 = 1180 - 1205mm
XY
ø 6.5
mm
Inside
32mm

5
Push fit the 'short flipper seals' onto the top and
bottom edges of both fixed panels - flush against
the metal profile. Ensure the flipper seal 'flaps' are
on the inside of the fixed panels. Note: Wetting
the glass with water will help fit the seals.
6
Position the fixed panels into the wall channels and slide down
so that they fully slot onto the end mouldings of the bottom rail.
Inside the enclosure, ensure the panels sit in the 'fixed panel
brackets', slide the fixed panel brackets along the rails and
position under the panels as shown.
4
Outside
face of fixed
panels
Out-
side
face of
fixed
panel
7
Position the top rail onto the top of the
'fixed panels'. Adjust the position of the
fixed panel brackets as required.
Line up the holes and fix the top rail
using 2 x 13mm screws.
Out-
side
face of
fixed
panel
Fixed
panel
bracket
13mm
Inside

10mm
5
8
Check the door frame is vertical and is centrally positioned between the wall channels.
From inside the enclosure, in the positions shown, drill through the wall channels into the fixed panels using a 3mm drill bit,
do not drill too deep! Fix using 6 x 10mm screws.
ø 3
mm
From inside
9
Fit 'flipper seals' (PN40308) onto the edge of the fixed
panels. Ensure the flipper seal 'flaps' are on the
inside.
Note: Wetting the glass with water will help fit the seals.
From inside the enclosure, place the fixed panel
retainer covers (PN80618) onto the top and bottom
fixed panel brackets. Fix using 12mm screws and fit
the retainer caps (PN50370).
10
Push fit 'flipper seals' (PN40275) onto the back edge of the doors.
Ensure the flipper seal 'flaps' are on the outside of the doors.
Push fit 'magnetic seals' (PN80564) onto the closing edge of the
doors (the same side as door handle hole).
Note: Ensure the magnetic seals are positioned as shown.
Note: Wetting the glass with water will help fit the seals.
Door
handle
holes
PN40275
Outside
face of
door
PN40275
PN80564
Door
handle
holes
Outside
face of
door
PN80564
PN80618
Inside
PN40308 PN50370
12mm
Fixed
panel
bracket

a
b
Plunger
From
outside
6
It is advised that this stage is carried out by two people to avoid damaging the runners, rails or doors.
a: From inside the enclosure, hang the top 'door rollers' onto the top rail 'runner'.
b: From outside (with the door closed) depress both 'plungers' on the bottom 'door rollers' and position under the bottom rail
'runner' and release the 'plungers'.
11
From inside
The 'wheels' at the top of the doors may need adjusting so that the doors slide freely and the magnetic seals meet evenly when
the doors are closed.
From outside the enclosure, turn the adjuster screw (under each of the top wheels) as shown until the doors hang vertically.
12
From inside
Ensure doors are adjusted
so the bottom wheels are
engaged in the bottom rail and
they are under light tension but
still free to run.

7
Fit the door
handles to
the doors
with the
allen bolts
on the inside
of the door.
Ensure
the rubber
washers
are placed
between the
handles and
the glass.
Do not over
tighten.
13
a: Check that the doors hit the top and bottom bumpers at the same time.
b: To adjust the bumpers, loosen the screw, move the 'rubber' bumper as required then re-tighten. Push fit cover caps (PN4745).
Inside
PN50359
PN11031
PN11031
ab
15
a: Insert 3 wall channel clips (PN50359) down the slot in each wall channel and space out equally down their length.
b: Push fit the wall channel cover strips (PN11031) onto the wall channels as shown.
ab
16
Door Door
PN4745
14
Slide the wheel cover
caps (PN60490) on
to the back of the
wheels as shown
from the inside of the
enclosure.
Top
Bottom

17
From the outside only, apply sealant to the bottom of the enclosure and 50mm up the wall channels and vertical joints as
shown.
50mm
CORAM SHOWERS LTD
Stanmore Industrial Estate, Bridgnorth, Shropshire WV15 5HP, UK •Tel: [phone] •Fax: [phone] • www.coram.co.uk
Recycling
Packaging:- The cardboard and polythene parts of this packaging can be recycled.
End of life:- This product contains materials such as aluminium and glass which can be recycled.
Please contact your local authority to find your nearest recycling centre.
IMPORTANT: You must not use the shower for 24 hours after installation of the enclosure.
DO NOT use bleach, scouring powders, solvents or other aggressive cleaning agents. To clean, use warm soapy water and a
clean cloth and rinse off.
Please note: There has been a glass coating applied to this product, use a squeegee to remove water and debris.
Periodically check all fixings and tighten if necessary.