AQUAS AQUA FULL PRO 9.5 KW User manual

These instructions contain all the necessary fitting and operating instructions for your electric shower.
Care taken during the installation will provide a long, trouble free life from your shower.
INSTRUCTION GUIDE AND USER MANUAL
INSTANTANEOUS ELECTRIC WATER HEATER - MANUAL
AQUA FULL PRO 9.5 KW.
AQUA TOP 9.5 KW. AQUA FULL PRO FLEX 9.5 KW.
AQUA PRO 9.5 KW.
By
AQUABELLA SHOWER CO.,LTD.

PLEASE READ THIS IMPORTANT SAFETY INFORMATION
Page 2

IMPORTANT
GENERAL ADVICE TO SHOWER UNIT USERS
Page 3

BATHROOM
FLOOR
CEILING JOISTS
SPILL
OVER
LEVEL
HOSE
RETAINING
RING
DOUBLE POLE SWITCH CEILING MOUNTED
GENERAL LAYOUT OF A SHOWER INSTALLATION
Page 4

AQUA FULL PRO 9.5 KW. AQUA FULL PRO FLEX 9.5 KW.
RECOMMENDED INSTALLATION DIMENSIONS
Page 5

AQUA TOP 9.5 KW. AQUA PRO 9.5 KW.
RECOMMENDED INSTALLATION DIMENSIONS
Page 6

AQUA FULL PRO 9.5 KW.
Page 7

AQUA TOP 9.5 KW.
Page 8

AQUA PRO 9.5 KW.
Page 9

Page 10

Page 11

Top fixing position
arrow depict water and
electrical entry points.
PLUMBLING CONNECTIONS
Page 12

PLUMBLING CONNECTIONS
Page 13

ELECTRICAL CONNECTIONS
Page 14
2 2

ELECTRICAL WIRING
Page 15

FITTING THE BACK COVER INTO POSITION
DIVERTOR HANDLE ( UPPER HANDLE )
VOLUME CONTROL HANDLE ( LOWER HANDLE )
Make sure that the Divertor spindle and the raised button on the divertor handle are in the
12 O'clock position before fitting the cover.
Turn the stabilizer valve spindle and volume handle fully clockwise until resistance is felt.
Fit cover into position and re-fit cover fixation screws.
Stabilizer valve
Divertor spindle
When fitting the cover, it is important to align the divertor spindle and
volume control spindle inside the heater.
Page 16

COMMISSIONING THE SHOWER HEATER
3. Before fitting the cover,
turn off the electricity supply.
Remove this square plastic part
in the picture. Fit the front cover.
Turn on the water and electricity again,
and the product should now work normally
2. Turn on the water
and electricity,
before fitting the front cover.
Push the on/off button,
to check water flow and
if there is any leakage
inside the heater or
at any shower connection.
1. Before installation,
rotate the volume control
handle clockwise until
resistance is felt.
Connect the water
and electricity supply.
IMPORTANT NOTE FOR THE INSTALLER
Page 17

OPERATING THE SHOWER
1. Switch on electrical supply - pull cord or wall mounted switch.
2. Press the ON / Off Button to start the flow of water.
3. Turn the divertor handle
to select the showering
function you require
Left for Hand-shower –
Right for Overhead.
4. When turning the Volume
Control Handle, this will
change slightly the output
temperature of the water.
5. To turn off the shower unit,
press the ON / OFF button.
IMPORTANT NOTE
The Higher the flow the temperature will decrease.
The Lower the flow the temperature will increase.
DIVERTOR HANDLE
HAND-SHOWER
OR OVERHEAD FUNCTION
VOLUME CONTROL HANDLE
ON / OFF BUTTON
Page 18

MAINTENANCE – CLEANING THE FILTER
STEP 1
Remove front cover assembly, loosen these two screws, the decor cover can be removed.
STEP 2
STEP 3
Use flat-head screw driver to remove filter, clean it, and refit.
Clean the filter and refit.
Page 19

2. If scale deposits are stubborn,
Soak the shower-head or hand-shower
in a proprietary Limescale remover and
rinse thoroughly before use.
Your AQUAS Branded heaters are supplied by Aquabella Shower Co.,Ltd. in Thailand.
For information or service assistance , please contact the installer or the local
UK distributor from where the heater was purchased.
Ai0051
1. To break away scale deposite on a daily
basis simply rub your thumb over the surface
whilst the shower is running.
SHOWERHEAD CLEANING INSTRUCTIONS
Page 20