Aquatec AquaPro AP6000HM User manual

MULTI-USE PUMPS
INSTRUCTIONS MANUAL
MANUFACTURED FOR
PO Box 648, Maddington, Western Australia, 6989
Telephone [phone]
Email [email protected]
www.aquatecequipment.com
www.aquatecequipment.com
IMPORTANT SAFEGUARDS
To guard against injury, basic safety precautions
should be observed including, but not limited to
the following;
•Thepumpshouldonlybeusedincleanwater. Do not use the pump in any solvent or
gasoline that is flammable.
•Donotoperatethepumpwithoutwateratany time, permanent damage may occur.
•Donotoperatethepumpifthepumporanyof the components of the pump, such as the
power cable, have been damaged.
•Thedriploopmethodshouldbeusedtoprevent water from traveling down the cord
onto the plug or power point. If the plug does
get wet, do not unplug the cord. Disconnect
the circuit breaker that supplies power to the
power point. Then unplug and examine the
plug and power point for presence of water. If
the power point has become wet, you should
consult an electrician before using the power
point again.
•Alwaysuseaproperlygroundedpowersupply that is connected to an RCD
with a rated residual operating current
not exceeding 30mA. As per AS/NZS
3350.2.41:1997.
•Alwaysunplugthepumpfromthepowersupply when not in use or before performing
any maintenance on the pump. Never pull
the cord to disconnect the plug from the
power supply. Grasp the plug and pull to
disconnect.
•Donotinstallorstorethepumpwhereit will be exposed to extreme hot or cold
temperatures.
•Donotcutthecordasthiswillresultinvoiding your warranty.
•Careshouldbetakentoarrangethepowercord so that it cannot be accidently tripped
over or pulled.
•Donotattempttorepairthepumpyourself.Return to an authorized service centre or
place of purchase if a fault occurs.
•Donotuseinwaterabove35°C.LIMITED WARRANTY
•Warrantycoversonlyappliancedefectsandfaulty material and workmanship within a 2
year period.
•Faultsarisingdueto;accidents,misuse,not following manufacturer’s guidelines/
instructions, or power surges/spikes/
brownouts will not be covered.
•Theimpellorsetisaconsumableitemandistherefore not covered under warranty.
•Warrantywillbevoidifanytampering,removal of warranty labels, or electrical
circuitry is evident.
•Warrantywillbevoidifthepowercordiscutor damaged in any way.
•Warrantywillbevoidifanyvisiblesignsofoverheating are present.
•Lossoflivestock,damagetopropertyorpersonal injury caused by this product will
not be covered.
•Warrantyclaimscausedbyinstallationfaultswill not be covered.
•Itisthecustomer’sresponsibilitytoreturnthe faulty appliance for any warranty claim,
to Aquatec.
•Foranywarrantytobevalid,anoriginalproofof purchase must be provided.
•Ourgoodscomewithguaranteesthatcannot be excluded under the Australian
ConsumerLaw.Youareentitledtoareplacement or refund for a major failure and
for compensation for any other reasonably
foreseeablelossordamage.Youarealsoentitled to have the goods repaired or
replaced if the goods fail to be of acceptable
quality and the failure does not amount to a
major failure.
Note: Please consult your retailer for quality original Aquapro replacement parts for your Aquapro
product. Visit www.aquatecequipment.com for nearest stockists.

MULTI-USE PUMPS
INSTRUCTIONS MANUAL
Congratulations on your purchase of this product by AquaPro,
the answers for your watergarden made easy!
DESCRIPTION AND FEATURES
YourAquaproWaterfeaturepumphasbeenmanufactured with advanced technology to
provide you with the best quality pump for
your pond or water feature.
•Aquapropumpsaresuitableforuseinmany different applications including;
fountains, water features, small ponds
and hydroponics.
•YourAquapropumphasasinglemovingpart (an impellor set) therefore enabling
easy cleaning and maintenance.
•Themotorandelectricalcomponentsareencapsulated in epoxy resin, ensuring
safe operation under water.
•Thepumphasarobustbearingandshaft design so no oil/grease lubrication
is required.
•TheAquapropumpsthathaveplasticencased impellor parts and ceramic
shafts (no exposed metal) may be used
in salt water applications.
•CheckouttheAquaprorangeofpondlights and accessories.
INSTALLATION
1. If required, have a qualified electrician
install weatherproof power point near
to the pond or water feature, (within the
cable length of the pump).
2. Place the pump in desired location,
ensure it is on a stable surface free of
sludge/debris and connect tubing to
the outlet.
3. Ensure pump is submerged, then plug
in power cord and switch on.
MAINTENANCE
Disconnect power cord from the power
supply before performing maintenance.
Never lift the pump by the power cord.
The only serviceable item is the impellor set.
The motor unit of the pump is
encapsulated with epoxy resin and does
not need lubrication.
All Aquapro submersible pumps are water
cooled; if pump becomes restricted it
will overheat and could cause permanent
damage. Ensure pump does not become
blocked or restricted.
The power cord cannot be replaced. If
the cord is damaged, the pump must be
discarded.
The impellor set is a wearing consumable
part. Regular inspections, cleaning and
maintenance of impellor is necessary to
ensure longer impellor life.
If the impellor set becomes worn or
damaged it should be replaced (available
from your dealer or special orders). Failure to
do so may cause serious damage to pump.
1. Disconnect the power cord before
performing maintenance.
2. Remove front filter cage by gently
squeezing sides.
3. Unscrew the four large screws facing
the rear of the motor and remove the
impellor housing.
4. Gently remove o’ring seal and impellor
set. Clean the impellor and impellor
chamber, taking care not to damage or
scour surfaces. Check for any signs of
wear or damage.
5. Reinstall the complete impellor set,
making sure the locator probe fits into
the hole on the impellor set. Put the
impellor set in firmly. Carefully replace
o’ring seal. Check the impellor can
spin freely.
6. Put impellor housing back on and screw
the four screws back in, making sure
the screws are done up evenly.
7. Replace front filter cage, re-attach
outlet, submerse in water and turn on.
AP6000HM AP7500HM
VOLTAGE(V)240 240
POWER (WATTS) 75 150
MAX HEIGHT (M) 4.00 4.20
FLOWMAX(L/H)6000 7500
CABLELENGTH(M)10 10
1 Outer Filter Screen
2 Inner Filter Screen
3 Impellor Cover/ Housing
4 Impellor Assembly
5 Motor Body
6 Stepped Outlet Hosetail
1 2 3 4
6
5
AP7500 Model shown. Picture for illustration purposes only..