Aquatic Fundamentals 16291U Datasheet

HARDWARE
2299//3377
GGAALLLLOONN UUPPRRIIGGHHTT AAQQUUAARRIIUUMM SSTTAANNDD
MMODEL 1166229911UU
E ASY A SSEMBLY I NSTRUCTIONS AND P ARTS L IST
THANK YOU FOR
PURCHASING THIS
QUALITY PIECE OF
FURNITURE.
AQUATIC FUNDAMENTALS
IS DEDICATED TO
PROVIDING A QUALITY
PRODUCT AND WILL MAKE
EVERY ATTEMPT TO
DELIVER CUSTOMER
SATISFACTION.
85155 07/04
2
PARTS LIST
3
NNOOTTEE::
THESE HOLES ARE NOT
USED FOR ANY
ASSEMBLY PURPOSES.
AQUATIC FUNDAMENTALS
CUSTOMER SERVICE
5400 Doniphan Drive
Neosho, Mo. 64850
E-mail us at:
[e-mail]
Visit our Web Page:
www.marcogroupinc.com
D
A
3x
20x
TOOL(S) REQUIRED
EF
2x 4x G
DOOR
HINGE
HARDWARE
BAG
Assemble furniture on the carton or carpet to protect the finish.
Clean furniture with a soft cotton cloth moistened with water.
DO NOT use abrasives.
DO NOT leave water on any of the stand’s surfaces. Always wipe
spilled water from the stand. Water, for prolonged periods, could
damage the stand’s surface.
A
SSEMBLY & C ARE
PHILLIPS HEAD SCREWDRIVER
B
1
C
20x
H
B
EFORE B EGINNING A
SSEMBLY :
PLEASE REVIEW THE PARTS LIST TO ENSURE THAT YOU HAVE ALL THE PARTS.
IF YOU FIND MISSING OR BROKEN PARTS, OR ARE IN NEED OF ASSEMBLY GUIDANCE, CALL TOLL FREE,
1-888-627-2601 AND WE’LL BE HAPPY TO HELP.
PLEASE, DO NOT RETURN THIS MERCHANDISE TO THE STORE.
I MPORTANT S AFETY I NFORMATION
PLEASE READ ALL THE FOLLOWING INFORMATION BEFORE
ASSEMBLING AND USING YOUR AQUARIUM STAND.
THIS PRODUCT IS NOT A TOY. NEVER allow small children to touch,
climb on or play with the aquarium or
the aquarium stand. Serious injury or death could result.
WHERE TO PLACE YOUR AQUARIUM
Use only an aquarium stand designed to support the weight and size of your aquarium.
The filled weight of an aquarium is approximately 10 to 12 pounds per gallon.
This stand is designed only for use on level surfaces. Failure to place your stand on a
level surface could cause the aquarium to leak, crack or even tip or fall.
Never tip the stand from it’s upright position.
MOVING YOUR AQUARIUM STAND
Always position the stand in the desired location before putting the aquarium tank in place.
Never attempt to move the stand with the aquarium in place.
Never remove an aquarium tank from the stand unless the aquarium tank is completely
empty. Never carry the stand by it’s top.
5
44
4
5
NOTE:
P
ART
#1
H
AS
E
XTENDED
L
IP
.

44
12
85155 Pg. 2
LIMITED WARRANTY
This aquarium stand is under warranty by Marco Group, Inc. against defects in material and workmanship for 90 days from the date of purchase. If any
component of the stand is found to be defective, you may contact us for replacement provided it has not been modified, damaged or misused.
(Proof of date of purchase must be provided).
THIS WARRANTY IS VOID if the aquarium stand is modified, if it is not placed on a flat, level surface, if it is used with a tank other than it is designed, if it is
moved with the tank in place or if it is used for other than it’s intended purpose.
This warranty is limited to replacement of the stand only. Warranty does not cover loss of fish, personal injury, property loss or damage arising out of use of the
aquarium stand. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to
you. This warranty gives you specific legal rights and you may have other rights that vary from state to state.
5400 DONIPHAN DRIVE
NEOSHO, MO 64850
FFOOLLLLOOWWSSTTEEPPSSIINNOORRDDEERR::
1. PLACE ONE SPACER “E” INTO THE HINGE
HOLE IN BOTTOM OF PART #1. NOW PLACE
THE BOTTOM DOOR HINGE INTO THIS SPACER.
2. PLACE ONE SPACER “E” ONTO THE TOP
DOOR HINGE AND INSERT IN THE HINGE HOLE
ON TOP PART #2. SECURE TOP HINGE “G” TO
DOOR WITH (2) SCREWS “F” AS SHOWN.
IMPORTANT 
IF DOOR DOES NOT OPEN PROPERLY OR IF PART
“G” MOVES WHILE OPENING DOOR, CAREFULLY
RE-CHECK THE INSTALLATION OF PART “G”.
A COMMON MISTAKE IS TO INSTALL PART “G”
BACKWARDS. PLEASE REFER TO PICTURES
IN STEPS 3 & 4 FOR CORRECT ORIENTATION.
STEP 1
IMPORTANT!!!
NOTE ORIENTATION OF
PART “A”. OPEN (HOLE)
SECTION MUST FACE
TOWARDS THE
CORRESPONDING HOLE
IN EDGE OF PARTS #4 & #5.
(ALL 20 PLACES)
THE ARROW ON TOP OF
PART “A” WILL ALSO
POINT TOWARDS THE
CORRESPONDING HOLE
IN EDGE OF PARTS #4 & #5.
TOP VIEW
OF “A”
FRONT VIEW
OF “A”
Insert (20) Part “A”
into holes as shown.
4
B
A
2
1
3
NOTE! HOLES & PART “B”
SHOWN HERE ARE ON
UNDERSIDE OF PART #2
STEP 2
Connect Parts #4 & #5 to
BOTTOM PART #1 FIRST.
Using a screwdriver, turn Part
“A” clockwise to lock onto Part
“B” on BOTTOM Part #1.
Repeat with TOP PART #2.
5
5
This side
faces to
INSIDE of
stand This side
faces to
INSIDE of
stand
STEP 3
F
Inside of
Door
Attach hardware to
BOTTOM of door FIRST.
E
Outside
of Door
STEP 4
E
F
G
BOTTOM
DOOR
HINGE
STEP 5
D
2X
Screw (20)
Part “B”
into holes
as shown.
2X
NOTE:
Lock bottom
assembly FIRST.
NOT
USED
NOT
USED
HINGE
HOLE
55
4
4
4
This
side
faces to
INSIDE
of stand
IMPORTANT
NOTE!
YOU MUST
POSITION TANK
TOWARDS THE
BACK SIDE
OF STAND.
H
DC
G