Aquatic Fundamentals 13551B User manual

2
MIXED MEDIA STAND
MODEL 13551B
FOR 55 GALLON TANK
THANK YOU FOR
PURCHASING THIS
QUALITY PIECE
OF FURNITURE.
AQUATIC FUNDAMENTALS
IS DEDICATED TO
PROVIDING A QUALITY
PRODUCT AND WILL MAKE
EVERY ATTEMPT TO DELIVER
CUSTOMER SATISFACTION.
85230 04/08
PA R T S LI S T
HA R D W A R E
C
TOOLS REQUIRED
L
E
DOOR
HINGE
HARDWARE
BAGS
Assemble furniture on the carton or carpet to protect the finish.
Clean furniture with a soft cotton cloth moistened with water.
DO NOT use abrasives.
DO NOT leave water on any ofthe stand’s surfaces.Always wipe
spilled water from the stand.Water,for prolonged periods,could
damage the stand’s surface.
A SSEMBLY & C ARE
PHILLIPS HEAD SCREWDRIVER
(8X) (2X)
(4X)
(28X) (28X)
(2X) (2X)
(6X)
BF
BEFORE BEGINNING ASSEMBLY :
PLEASE REVIEW THE PARTS LIST TO ENSURE THAT
YOU HAVE ALL THE PARTS. IF YOU FIND MISSING OR BROKEN PARTS, OR ARE IN NEED OF ASSEMBLY
GUIDANCE, CALL TOLL FREE, 1-888-627-2601 AND WE’LL BE HAPPY TO HELP.
PLEASE, DO NOT RETURN THIS MERCHANDISE TO THE STORE.
ALLEN WRENCH (INCLUDED)
(16X)
A
D
JK
I MPORTANT S AFETY I NFORMATION
PLEASE READ ALL THE FOLLOWING INFORMATION BEFORE
ASSEMBLING AND USING YOUR AQUARIUM STAND.
THIS PRODUCT IS NOT A TOY. NEVER allow small
children to touch, climb on or play with the stand.
Serious injury or death could result.
WHERE TO PLACE YOUR AQUARIUM STAND
Use only a stand designed to support the weight and size of your equipment.
(HINT: If using for an aquarium stand, the filled weight of an aquarium is
approximately 10 to 12 pounds per gallon. This stand is designed only for use on level
surfaces. Failure to place your stand on a level surface could cause the aquarium to
leak, crack or even tip or fall). Never tip the stand from it’s upright position.
MOVING YOUR STAND
Always position the stand in the desired location before putting the equipment in
place. Never attempt to move the stand with the equipment in place.
Never remove an aquarium tank from the stand unless the aquarium tank is
completely empty. Never carry the stand by it’s top.
LIMITED WARRANTY
This aquarium stand is under warranty by Marco Group, Inc. against defects in material and workmanship for 90 days from the date of purchase. If any
component of the stand is found to be defective, you may contact us for replacement provided it has not been modified, damaged or misused.
(Proof of date of purchase must be provided).
THIS WARRANTY IS VOID if the stand is modified, if it is not placed on a flat, level surface, if it is used with a tank other than it is designed,
if it is moved with the tank in place or if it is used for other than it’s intended purpose.
This warranty is limited to replacement of the stand only. Warranty does not cover loss of fish, personal injury, property loss or damage arising out of use of the
aquarium stand. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not
apply to you. This warranty gives you specific legal rights and you may have other rights that vary from state to state.
GH
(2X)
(8X)
5(8X)
Note orientation
of hinge pivot
3
(2X)
NOTE:
T HESE H OLES A RE N OT
U SED F OR A NY
A SSEMBLY P URPOSES .
(2X)
7
NOT E:
THESE HOLES ARE NOT
USED FOR ANY
ASSEMBLY PURPOSES .
68
(2X)
1
(1X)
(4X) 4
(2X)
NOTE:
PART #’s 3 & 4 ARE THE SAME SHAPE & SIZE.
PART #4 HAS 2 EXTRA HOLES.
(2X)
AQUATIC FUNDAMENTALS
CUSTOMER SERVICE
5400 Doniphan Drive
Neosho, Mo. 64850
Visit our Web Page:
www.marcogroupinc.com
E-mail us at:
[e-mail]
1-888-627-2601
NOTE:
PART # 6 IS SLIGHTLY SMALLER
THAN PART #’S 3 & 4.
NOT E:
THESE HOLES ARE NOT
USED FOR ANY
ASSEMBLY PURPOSES .

85230 04/08 Pg. 2
FOL LOW ST EPS IN ORDER:
1. PLACE ONE SPACER “J” INTO THE HINGE
HOLE IN BOTTOM OF PART #2. NOW PLACE
THE BOTTOM DOOR HINGE INTO THIS SPACER.
2. PLACE ONE SPACER “J” ONTO THE TOP
DOOR HINGE AND INSERT IN THE HINGE HOLE
ON TOP PART #2. SECURE TOP HINGE “L” TO
DOOR WITH (2) SCREWS “K” AS SHOWN.
3. REPEAT ABOVE STEPS WITH OTHER DOOR
FOR RIGHT SIDE OF UNIT.
I M P O R T A N T
IF DOOR DOES NOT OPEN PROPERLY OR IF PART
“L”MOVES WHILE OPENING DOOR,CAREFULLY
RE-CHECK THE INSTALLATION OF PART “L”.
A COMMON MISTAKE IS TO INSTALL PART “L”
BACKWARDS.PLEASE REFER TO PICTURES
IN STEPS 8 & 9 FOR CORRECT ORIENTATION.
Attach Part “L” (hinge) to
BOTTOM of doors FIRST.
DO NOT attach TOP
Hinges until STEP 9.
BOTTOM
DOOR
HINGE
HINGE
HOLE
STEP 2
Using a screwdriver,
screw (28) Parts “C”
into each Part #’s 2 & 4.
DO NOT USE POWER
DRIVERS OR POWER
TOOLS - THEY CAN
STRIP THE HARDWARE.
B
7
K
F
E
LD
6
STEP 3
Slide Part #’s 3, 4 & 8 onto the
(6) Parts “C” in Bottom Part #2.
Insert a second Part #2 onto
the top of Part #’s 3, 4 & 8.
Using a screwdriver, hand tighten
Parts “B” onto Parts “C” (12 places).
DO NOT USE POWER DRIVERS
OR POWER TOOLS - THEY CAN
STRIP THE HARDWARE.
REPEAT ABOVE STEPS WITH
REMAINING PART #’S 2, 3, 4 & 8.
(This will create 2 boxes - a left
side and a right side).
ON RIGHT SIDE BOX, NOTE
THAT THE PARTS “C” ON
PART #4 WILL FACE THE
OUTSIDE, AND TOWARDS THE
LEFT SIDE BOX (See Figure A)
J
5400 DONIPHAN DRIVE
NEOSHO, MO 64850
Toll Free: 888-627-2601
www.marcogroupinc.com
[email protected]
TANK PLACEMENT DETAIL
TOP VIEW
OF “B”
FRONT VIEW
OF “B”
IMPORTANT!!!
NOTE ORIENTATION OF PART “B”.
OPEN (HOLE) SECTION MUST FACE
TOWARDS THE CORRESPONDING
HOLE IN EDGE OF PART NUMBER’S
3, 4, 6 & 8.
THE ARROW ON TOP OF PART “B”
WILL ALSO POINT TOWARDS THE
CORRESPONDING HOLE IN EDGE OF
PART NUMBER’S 3, 4, 6 & 8.
STEP 1
Push in (28) Parts “B” into Part #’s 3, 4, 6 and 8.
PART “B” MUST BE INSERTED CORRECTLY.
REPEAT ABOVE FOR
RIGHT SIDE DOOR.
3
(2X)
8
(2X)
4
(2X)
(1X)
2(4X)
C
H OLES
ARE
F ACING
I NSIDE
3
2
4
2
C
C
IMPORTANT:
Part “C” faces to the
outside on Part #4.
B
IMPORTANT:
Note orientation of Part #2.
Hole configurations face to
the front for assembly.
Figure A
RIGHT SIDE BOX
4
2
C
8
4
(2X)
STEP 4
Carefully rotate both boxes onto back side.
Slide Part #6 onto Parts “C” on Left Box.
Carefully Slide Right Box into holes On Part #6.
Hand tighten (4) Parts “B”.
6
LEFT SIDE
RIGHT SIDE
C
B
Use extreme caution
and carefully rotate
the stand upright.
Inside of
Left Door
7
Inside of
Right Door
KL
E
F
J
F(2X)
LEFT SIDE
You MUST PositionTank towards
the BACK of Stand!
LEFT SIDE BOX
F IRST
S ECOND
G
H
T HIRD
F OURTH
1
1
Using the Allen wrench (included),
attach (8) Parts #5 with (8) Parts “A”
into each box assembly.
Partially screw (4) Parts
“H” through Part “G” &
into Left Part #1 in
sequences FIRST &
SECOND as shown.
Connect and align both Parts #1.
Partially Screw (4) Parts “H” through Part
“G” and into other Part #1 in sequences
Tighten all screws when both Parts #1 are properly aligned.
Attach top assembly to bottom
unit using (8) Parts “A”.
THIRD & FOURTH as shown.
5(8X)
A
Lay out both Parts #1
as shown.
STEP 5 STEP 6 STEP 7
A(8X)
(2X)
(2X)
Note hinge
pivot location
Note hinge
pivot location
Parts “C” screw through
small holes this side.
(Important: Parts “B” are
inserted on other side)
STEP 8 STEP 9
LEFT
SIDE
7
Outside of
Left Door
K(2X)
L
STEP 10
IMPORTANT!
Use extreme caution when
handling, lifting and moving
completed assembly.
Do not move unit with tank.