Aquavision AVF-10.4-4 User manual

WWW.AQUAVISION.CO.UK
Tel [phone]
Bezel Installation Guide
Bezel Installation GuideBezel Installation Guide
Bezel Installation Guide
Thank you for purchasing an AQUAVISION
Thank you for purchasing an AQUAVISIONThank you for purchasing an AQUAVISION
Thank you for purchasing an AQUAVISION Television.
Television.Television.
Television.
Safety
SafetySafety
Safety
AQUAVISION recommends installation to be carried out by a qualified installer. Please ensure that the latest wiring and
safety regulations are adhered. If your AQUAVISION is powered by a low voltage (12/24v DC) power supply unit, this
should be positioned away from any water source. Please observe the safety zones in bathrooms and other wet areas. IF
IF IF
IF
IN DOUBT REFER TO A QUALIFIED PERSON. THIS APPLIANCE AND THE BEZEL MUST B
IN DOUBT REFER TO A QUALIFIED PERSON. THIS APPLIANCE AND THE BEZEL MUST BIN DOUBT REFER TO A QUALIFIED PERSON. THIS APPLIANCE AND THE BEZEL MUST B
IN DOUBT REFER TO A QUALIFIED PERSON. THIS APPLIANCE AND THE BEZEL MUST BE EARTHED
E EARTHEDE EARTHED
E EARTHED
Positioning
PositioningPositioning
Positioning
Each AQUAVISION model has specific viewing angles. Position the front bezel in order to view the picture clearly from
all intended areas. Should there be any doubt, make the area safe and power up the LCD, positioning the screen until
satisfied that the picture does not darken or disappear from view.
Wall
Wall Wall
Wall M
MM
Mounting and
ounting and ounting and
ounting and C
CC
Cable
able able
able F
FF
Feed
eedeed
eed
When the position has been defined, cut a hole in the wall to the cut-out dimensions specified for your AQUAVISION
model (Fig. 2).
Next, fit the two side mounting brackets into the sides of the hole following the guidance offered in either Fig. 3 or 4
depending on the wall structure.
Fig. 3 uses the brackets as a clamp between the front and back of a partition (stud) wall or in Fig. 4 the bezel brackets
must be fixed to a solid wall using six screws (not provided).
Do not over tighten the screws holding the front bezel onto the brackets as this can distort the frame and may hinder
installation of the glass on the final fix. When fitted, the unit should be able to withstand a potential pull force of 100Kg.
Run the cables to their positions as shown in Fig. 1, ensuring that there is enough cable slack to connect to the rear of the
AQUAVISION unit. Ensure that the cables are easily available and cannot fall back into the cavity, etc.
Final
Final Final
Final Fix
FixFix
Fix
The wall can now be tiled. You must take care not to bend or damage the inner flange of the bezel as this could
potentially hinder any water-proofing qualities and thus void any guarantee. Note it is not advisable to use raised border
tiles under the edge of the bezel frame. Once all tiles or similar have been fitted and the wall is in a finished state, loosen
the bezel screws and apply a bead of silicon all around the rear of the flange (See Fig. 3 or 4). This prevents moisture
from accessing the sides of the front bezel. Tighten the front panel ensuring the silicone fills any areas that could allow
ingress of water. The bezel is now in position to accommodate the LCD unit and finally the glass panel. Instructions on
fitting these components are supplied separately.
CABLING SCHEMATIC
CABLING SCHEMATICCABLING SCHEMATIC
CABLING SCHEMATIC
Fig 1
Fig 1Fig 1
Fig 1
All manuals and user guides at all-guides.com
all-guides.com

WWW.AQUAVISION.CO.UK
Tel [phone]
Aquavision Glass
Aquavision Bezel
Wall
Aquavision
Mounting Bracket
Aquavision Glass
Aquavision Bezel
Wall
Aquavision
Mounting Bracket
LCD TV
LCD TV
Silicone
Silicone
BEZEL SIZES AND CUTOUTS
BEZEL SIZES AND CUTOUTSBEZEL SIZES AND CUTOUTS
BEZEL SIZES AND CUTOUTS
Fig
Fig Fig
Fig 2
22
2
Model Screen Size
A
Overall
Height
B
Overall
Width
C
Cut-out
Height
D
Cut-out
Width
E
Maximum
Depth
AVF 104-4
AVF 104-4B
264mm
(10.4”)
318mm
(12.5”)
328mm
(12.9)
309mm
(12.2”)
319mm
(12.5”)
80mm
3.2”
AVF 17W-4 428mm
17”
371mm
14.6”
516mm
20.3”
362mm
14.3”
507mm
20”
100mm
4”
AVF 19-4 481mm
19”
371mm
14.6”
516mm
20.3”
362mm
14.3”
507mm
20”
90mm
3.6”
AVF20-4 508mm
20”
371mm
14.6”
516mm
20.3”
362mm
14.3”
507mm
20”
90mm
3.6”
AVF24-4 611mm
24”
492mm
19.4”
722mm
28.4”
483mm
18.9”
713mm
28”
90mm
3.6”
AVF 26-4 659mm
26”
492mm
19.4”
722mm
28.4”
483mm
18.9”
713mm
28”
115mm
4.6”
AVF 32-4 799mm
32”
571mm
22.5”
854mm
33.6”
562mm
22.1”
845mm
33.3”
120mm
4.7”
AVF40-4 1015mm
40”
692mm
27.2”
1049mm
41.3”
683mm
26.9”
1040mm
40.9”
120mm
4.7”
AVF46-4 1167mm
46”
725mm
28.5”
1172mm
46”
716mm
28.1”
1163mm
45.7”
120mm
4.7”
INSTALLATION SCHEMATIC
INSTALLATION SCHEMATICINSTALLATION SCHEMATIC
INSTALLATION SCHEMATIC
Fig
Fig Fig
Fig 3
33
3
Fig
Fig Fig
Fig 4
44
4
The specifications shown were accurate at time of going to press. AQUAVISION
AQUAVISIONAQUAVISION
AQUAVISION’S
SS
S policy of continuous development means some changes may take place.
Please check with the office for confirmation. All screen pictures simulated. E. & O.E. REV 4.0.7
C
E
D
1.2 THK TYP
B
A
All manuals and user guides at all-guides.com