Medion LIFE P14002 User manual

User Manual
P14002 (MD 31490) / P14304 (MD 31491) / P14901 (MD 31492)
MEDION® LIFE®
Full HD Smart-TV

Contents
1. Information about these operating instructions............................................................... 4
1.1. Explanation of symbols .........................................................................................................................4
1.2. Proper use...................................................................................................................................................5
2. Package contents.................................................................................................................. 5
3. Safety instructions ............................................................................................................... 6
3.1. Operating safety.......................................................................................................................................6
3.2. Set-up location ........................................................................................................................................7
3.3. Repairs .........................................................................................................................................................8
3.4. Environmental temperature ................................................................................................................8
3.5. Safety when connecting .......................................................................................................................8
3.6. Handling batteries...................................................................................................................................9
4. EU - Declaration of conformity .......................................................................................... 10
4.1. Information on Wifi .............................................................................................................................. 11
5. Overview of the device....................................................................................................... 12
5.1. Front .......................................................................................................................................................... 12
5.2. Rear and right-hand side.................................................................................................................... 13
5.3. Remote control...................................................................................................................................... 14
6. Using the device for the first time..................................................................................... 16
6.1. Unpacking ............................................................................................................................................... 16
6.2. Mounting ................................................................................................................................................. 16
6.3. Inserting batteries in the remote control..................................................................................... 17
6.4. Connecting the antenna .................................................................................................................... 17
6.5. Connecting the power supply ......................................................................................................... 18
6.6. Switching the smart TV on and off ................................................................................................. 18
6.7. Channel search when switching on for the first time.............................................................. 18
7. Multimedia connections .................................................................................................... 23
7.1. Use of the multimedia connections............................................................................................... 23
8. Operation ............................................................................................................................ 25
8.1. Channel selection ................................................................................................................................. 25
8.2. Sound settings....................................................................................................................................... 25
8.3. Screen settings....................................................................................................................................... 25
8.4. Displaying information ....................................................................................................................... 26
8.5. Opening the favourites list................................................................................................................26
8.6. Selecting the source ............................................................................................................................27
8.7. Wireless Display..................................................................................................................................... 27
9. Teletext................................................................................................................................ 28
9.1. Using the teletext ................................................................................................................................. 28
10. Via the OSD menu............................................................................................................... 29
10.1. Navigating in the menu......................................................................................................................29
10.2. The Q. MENU button............................................................................................................................ 30
10.3. The menu system in detail.................................................................................................................31
11. EPG – Programme guide .................................................................................................... 53
12. Media portal........................................................................................................................ 54
13. HbbTV system ..................................................................................................................... 55
14. Internet................................................................................................................................ 55
15. MEDION® Life Remote App ................................................................................................ 55
16. Data protection MEDION® Smart TV ................................................................................. 57
17. Troubleshooting ................................................................................................................. 58
2

17.1. Do you need more help?.................................................................................................................... 60
17.2. LCD TV pixel faults ................................................................................................................................ 60
18. Cleaning .............................................................................................................................. 61
19. Storage when not in use.....................................................................................................61
20. Disposal............................................................................................................................... 62
21. Technical data ..................................................................................................................... 63
21.1. Information on trademarks............................................................................................................... 65
22. Product data sheet ............................................................................................................. 66
23. Service information............................................................................................................ 67
24. Legal Notice ........................................................................................................................ 67
25. Index .................................................................................................................................... 68
3
EN

1. Information about these operating instructions
Thank you for choosing our product. We hope you enjoy using it.
Read the safety instructions and all other instructions carefully before using the device for
the first time. Note the warnings on the device and in the operating instructions.
Always keep the operating instructions close to hand. If you sell the device or give it away, please
ensure that you also pass on these operating instructions. They are an essential component of the
product.
1.1. Explanation of symbols
If a block of text is marked with one of the warning symbols listed below, the hazard described in
that text must be avoided to prevent the potential consequences described there from occurring.
DANGER!
Warning of immediate risk of fatal injury!
WARNING!
Warning: possible mortal danger and/or serious irreversible injuries!
CAUTION!
Warning: possible light or moderate injuries!
NOTICE!
Please follow the guidelines to avoid property damage.
Additional information on using the device!
Please follow the guidelines in the operating instructions.
Due to the 5 GHz frequency range of the used wireless LAN solution, use in EU countries
is only permitted inside buildings.
WARNING!
Warning of risk of electric shock!
WARNING!
Warning: danger due to loud volume!
• Bullet point/information on steps during operation
Instructions to be carried out
4

Declaration of conformity (see section “EU - Declaration of conformity”): Products that
feature this symbol meet the requirements of the EC directives.
Safety class II
Electrical appliances in protection class II are electrical appliances that permanent-
ly have double or reinforced insulation and do not have any connection options for a
protective earth. The housing of an electrical appliance in protection class II that is en-
closed in insulated material can partially or fully act as the additional or reinforced insu-
lation.
1.2. Proper use
This is an information technology device and is also suitable for multimedia applications. This de-
vice is used to receive and play back television programmes. The range of different connections
supplied makes it possible to expand the input and output sources (receiver, DVD player, DVD re-
corder, video recorder, PC, etc.). Your device offers a number of options for usage.
The device is intended for private use only and not for industrial/commercial use.
• Please note that we shall not be liable for damage caused by improper use.
• Do not modify the device without our consent and do not use any auxiliary equipment that we
have not approved or supplied.
• Use only spare parts and accessories that we have supplied or approved.
• Heed all the information in these operating instructions, especially the safety information. Any
other use is deemed improper and can cause personal injury or property damage.
• Do not use the device in extreme environmental conditions.
• This device is intended for use in dry, indoor areas only.
• This device is not designed to be used as a data monitor for office workplaces
2. Package contents
Please check your purchase to ensure that all the items are included and contact us within 14 days
of purchase if any parts are missing.
The following items are supplied with your product:
• Full HD Smart TV
• Remote control (RC4995) incl. 2 x 1.5 V batteries (type LR03/AAA)
• Stand including fastening screws
• Documentation
DANGER!
Risk of suffocation!
Packaging film can be swallowed or used improperly. Therefore, there is a risk of
suffocation!
Keep packaging material such as plastic film or plastic bags away from children.
5
EN

3. Safety instructions
3.1. Operating safety
− Check the device for damage before using it for the first time. A defective or damaged
device must not be placed into operation.
− This device may be used by children over the age of 8 and by persons with reduced
physical, sensory or mental abilities or by those without experience and knowledge, if
they are supervised or have been instructed in the safe use of the device and have un-
derstood the dangers that result from it.
− Children must not be allowed to play with the device. Cleaning and user maintenance
must not be carried out by children unless they are supervised.
DANGER!
Risk of suffocation!
Packing material is not a toy! Packaging film can be swallowed or used improperly.
Therefore, there is a risk of suffocation!
Keep packaging material such as plastic film or plastic bags away from children.
WARNING!
Risk of electric shock!
Risk of electric shock, short circuit and fire!
Never open the housing of the Smart TV and never insert any objects through
the slots and openings into your Smart TV.
WARNING!
Overheating! Risk of fire!
Overheating can damage your Smart TV and lead to a risk of fire!
The slots and openings on the TV are for ventilation purposes. Do not cover
these openings e.g. with newspapers, table cloths, curtains, etc.
− Do not put any pressure on the display. There is a risk that the glass on the screen may
break.
− The universal remote control has a class 1 infrared diode. Never use optical devices to
look at the LED.
CAUTION!
Risk of injury!
There is a risk of injury if the display is broken!
To avoid damaging the display, do not touch it with fingers or sharp objects.
Pick up the shattered pieces wearing protective gloves.
Then wash your hands with soap because chemicals may have leaked out.
Send the broken parts to your Service Centre for professional disposal.
− Disconnect the device from the mains network immediately in the event of an emer-
gency and only use it again when it has been checked by a qualified person or cus-
tomer services. Emergency situations include e.g. when smoke or unusual noises are
coming from the device, water has penetrated into it or the mains cable or housing is
damaged.
6

Contact customer services if:
− The power cable is burnt or damaged
− Liquid has penetrated the device
− The device is not operating correctly
− The device has fallen, or the housing is damaged
− Smoke is rising from the device
3.2. Set-up location
− In the first few hours of use, new devices can give off a typical, unavoidable but totally
harmless smell which wears off with time. We recommend that you ventilate the room
at regular intervals to counteract the smell.
We have taken appropriate measures during
the development of this device to ensure that levels
are significantly below legal limits.
− Keep your Smart TV and all connected appliances away from moisture and avoid dust,
heat and direct sunlight. Non-compliance with these instructions can lead to faults or
damage to the Smart TV.
− Do not use the device outdoors as it could be damaged by rain, snow, etc.
− The device must not be exposed to dripping or sprayed water. Do not place vessels
filled with liquid (vases or similar) on or in the vicinity of the device. The container may
tip over and the liquid may impair the electrical safety of the product.
NOTICE!
Risk of damage!
There is a risk of injury with candles and other open flames.
Keep candles and other open flames away from this device at all times in order
to prevent the spread of fire.
− Make sure that there is enough clearance from the sides of the furniture unit. Ensure a
minimum clearance of 10 cm around the device for sufficient ventilation.
− Avoid dazzle, reflections and strong bright-dark contrast in order to protect your eyes.
− The optimal viewing distance is 3 times the screen diagonal.
DANGER!
Risk of injury! Mortal danger!
Only set up your TV on a stable surface. Televisions that tip over could cause seri-
ous injuries or death. Lots of injuries, especially to children, can be avoided by ob-
serving the following safety precautions.
Operate all components on a stable, level and vibration-free base, to prevent the
Smart TV from falling over.
Only use the stand and screws supplied with the TV.
− Only use furniture that guarantees the safe use of the TV.
− Ensure that the TV does not hang over the edges of the furniture.
− Do not place the TV on higher or high furniture such as wall cabinets or shelves with-
out ensuring that both the furniture and the TV are safely and securely held in place.
− In order to guarantee the stability of the TV, do not place any sheets or similar under it.
− Advise children of the dangers of climbing up furniture in order to reach the TV or its
operating elements.
If you are storing or moving the TV, also observe the aforementioned safety instructions.
7
EN

3.3. Repairs
− Repairs to your Smart TV should only be carried out by qualified specialists.
− If a repair must be carried out, please only contact our authorised service partner.
− Make sure that only replacement parts provided by the manufacturer are used. The
use of unsuitable replacement parts may damage the device and lead to a risk of fire.
3.4. Environmental temperature
− The device can be operated at an ambient temperature of +5°C to +35°C with a rela-
tive humidity of 20% - 85% (non-condensing).
− When switched off, the Smart TV can be stored at temperatures from -20°C to +60°C.
− Keep the product at least one metre away from sources of high-frequency and mag-
netic interference (television set, loudspeakers, mobile telephones, etc.) in order to
avoid malfunctions.
− During thunderstorms or if the device is not going to be used for long periods, remove
the plug from the socket and the aerial cable from the aerial socket.
NOTICE!
Risk of damage!
Large changes in temperature or fluctuations in humidity can cause moisture to
build up due to condensation within the Smart TV, which can cause an electrical
short circuit.
After transporting the Smart TV, wait until the appliance has reached ambient
temperature before switching it on.
3.5. Safety when connecting
3.5.1. Power supply
− Even when deactivated, some components of the device are live. To disconnect the
power from your Smart TV or to completely isolate the device from voltage sources,
disconnect the device completely from the mains network. Disconnect the mains plug
from the mains socket for this purpose.
WARNING!
Risk of electric shock!
There is a risk of death due to an electric shock when the housing is open!
Do not open the housing of the device. It does not contain any parts requiring
maintenance.
− Only plug the Smart TV into earthed 220–240 V~ 50 Hz sockets. Contact your electrici-
ty provider if you are not sure if the socket is earthed or not.
− The socket must always be easily accessible so that the mains plug can be quickly dis-
connected from the socket in the event of an emergency.
− To disconnect the power supply to your TV, disconnect the mains plug from the mains
socket.
8

− For extra safety, we recommend using an over-voltage protection device to prevent
your Smart TV sustaining damage as a result of power surges or lightning strikes.
− Position the cables so that they cannot be stepped on or tripped over.
− Do not place any objects on the cables as they may be damaged.
− Do not touch the plug with wet hands.
− Always hold the plug by its housing and never pull it out of the socket using the cable.
− Please note that the TV also continues to consume power in standby mode (see here
the power consumption in standby mode in the section “Product data sheet” on page
66).
If the device shuts down and restarts due to an electrostatic discharge while in USB
mode (media player), optional HbbTV mode or optional LAN/WiFi operation (media
player/portal), it will not be able to independently restore the last operating mode.
Please restart the respective media or applications.
The last user settings you entered may not be restored following an electrostatic
discharge that causes the TV to shut down because these settings are only saved 5
minutes after switching channels.
All multimedia devices, which are connected to the corresponding ports of the TV,
must comply with the requirements of the Low Voltage Directive.
3.6. Handling batteries
WARNING!
Risk of explosion!
Batteries may contain combustible materials and leak, heat up excessively, ignite or
even explode.
Avoid improper handling of the batteries to prevent damage to your device and your
health.
Please follow the safety advice below closely:
− Keep batteries away from children.
If batteries are swallowed, consult a doctor immediately.
− Never charge batteries (unless they are designed to be recharged).
− Never empty the batteries by means of high power output.
− Never short-circuit the batteries.
− Never expose the batteries to excessive heat, such as sunlight, fire or similar sources of
heat!
− Do not dismantle or deform the batteries.
You could injure your hands or fingers, or battery fluid could come into contact with
your eyes or skin. If this happens, rinse the affected areas with plenty of clean water
and consult a doctor immediately.
− Avoid heavy impacts and vibrations.
− Always observe the correct polarity.
− Make sure that the plus (+) and minus (−) poles are correctly inserted to avoid short
circuits.
− Do not mix up new and old batteries or different types of batteries.
This could cause your device to malfunction. In addition, the weaker batteries would dis-
charge too much.
− Remove spent batteries from the device immediately.
9
EN

− Remove the batteries from the device if you do not intend to use it for a long period of
time.
− Replace all of the old batteries in a device with new batteries of the same type.
− Cover the contacts of the batteries with sticky tape if you want to store or dispose of them.
− If necessary, clean the battery and device contacts before insertion.
− If the batteries have leaked, wear protective gloves and clean the contacts thoroughly.
4. EU - Declaration of conformity
MEDION AG hereby declares that this product conforms with the essential requirements and the re-
maining relevant regulations:
• RE Directive 2014/53/EU
• Ecodesign Directive 2009/125/EC
• RoHS Directive 2011/65/EU
You can download the complete EU Declaration of Conformity from www.medion.com/conformity.
Use is only permitted inside buildings in all EU countries due to the 5 GHz frequency band of the in-
built Wireless LAN solution.
AT BE BG CZ DK
EE FR DE IS IE
IT EL ES CY LV
LI LT LU HU MT
NL NO PL PT RO
SI SK TR FI SE
CH UK HR
AT = Austria, BE = Belgium, CZ = Czech Republic, DK = Denmark, EE = Estonia, FR = France, DE =
Germany, IS = Iceland, IE = Ireland, IT = Italy, EL = Greece, ES = Spain, CY = Cyprus, LV = Latvia,
LT = Lithuania, LU = Luxembourg, HU = Hungary, MT = Malta, NL = Netherlands, NO = Norway,
PL = Poland, PT = Portugal, RO = Romania, SI = Slovenia, SK = Slovakia, TR = Turkey, FI = Finland,
SE = Sweden, CH = Switzerland, UK = United Kingdom, HR = Croatia
10

4.1. Information on Wifi
WLAN
Frequency range 2,4 GHz/ 5 GHz
Wi-Fi standard 802.11 a/b/g/n
Encryption WEP/WPA/WPA2
Frequency range/MHz Channel Max. transmission power/
dBm
2400 – 2483,5 1 - 13 19,9
5150 – 5250 36 – 48 22,4
5250 – 5350 52 – 64 22,5
5470 – 5725 100 – 140 22,5
11
EN

5. Overview of the device
5.1. Front
32
1
1) LCD screen
2) Mains switch (bottom of the device on the left or right)
3) Infrared sensor: Reception field for the infrared TV signals.
Operating light: Lights up when the device is in standby mode.
12

5.2. Rear and right-hand side
13
(ARC)
MODE - / I - O +
USB
5Vdc
Max. 500mA
USB
5Vdc
Max. 500mA
1
6
8
9
11
12
2
2
3
4
5
SPDIF
Optic. out
10
L
RVideo
BACK AV IN
13 Vdc/18 Vdc
300mA Max.
7
1) COMMON INTERFACE (CI+): Card slot for connecting pay TV cards
2) USB (5V , 500 mA max.): USB connection for media playback/recording (PVR)
3) HDMI 1: HDMI connection for devices with a HDMI output
4) : For connecting headphones with 3.5 mm jack
5) MODE: Multifunction button for channel switching, input source selection or volume adjust-
ment. Settings are made by tilting upwards (+) or downwards (-). Pressing the button briefly
switches between functions. A long press switches the device into standby mode or operat-
ing mode.
6) HDMI 2-3: HDMI connection for devices with a HDMI output (HDMI 2 can be used for CEC/
ARC)
7) LNB (13 V/18 V , 300 mA max.): For connecting the antenna (satellite)
8) ANT.: For connecting an aerial (analogue, DVB-T or DVB-C)
9) VGA: VGA port for connecting a PC or a YUV adaptor (optional)
10) BACK AV IN: Audio/video input (cinch)
11) SPDIF Optic. OUT: Digital audio output (optical)
12) LAN: Network connection to connect to the Internet
13) Fixing holes for a wall mount
13
EN

5.3. Remote control
OK
V
V
P
P
LAN G. SUBT.
EPG
TXT
Q.
MENU
MENUBACK
EXIT
2
1
.,/@
3
ABC
4
DEF
5
GHI JKL
6
MNO
7
PQRS
8
TUV
0
TV
9
WXYZ
1
2
3
4
5
6
7
8
10
12
13
14
16
15
17
18
19
27
26
24
25
11
20
21
23
22
9
1) : Switch smart TV on/off (switch standby mode on/off)
2) NETFLIX: Call up Netflix site
3) Number buttons:
TV: programme selection, teletext: page selection
4) (SWAP): Set previous TV programme
5) MENU: Open and close menu
6) : Internet button
7) P/+: Programme selection buttons
TV: select next (+) / previous (−) programme;
teletext: select next (+) / previous (−) page
8) OK: Confirm selection in certain menus
9) EXIT: Exiting the menu
10) (SOURCE): Select input signal of connected devices
14

11)
TXT
: Activate teletext
Press 2 x = set transparent;
Press 3 x = close
12) Q. MENU: Access the quick menu (OPTION MENU) to quickly call up basic options
13) : Switching between DVB-S, DVB-T and DVB-C channels / multifunction button for pro-
gramme channel or input source
14) Red button: For teletext or menus
Green button: For teletext or menus
Yellow button: For teletext or menus
Blue button: For teletext or menus
15) (SIZE): Select picture format
16) Media buttons
: Fast rewind;
: Fast forward;
: Start recording (PVR);
: Stop playback;
: Start playback;
: Pause playback
17) LANG.: Analogue TV: stereo/mono;
Digital TV: select audio language (if available)
18) SUBT.: Subtitles on/off (if available)
19) : Open the MEDION® portal /multifunction button for channel position or input source
20) (MEDIA): Call up the media browser
21)
EPG
(EPG): Digital TV: call up the electronic programme guide
22) i (INFO): Digital TV: show information (e.g. current channel number)
23) : Mute
24) V/+ : Increase (+) or decrease (−) volume.
25) Direction button : Move up in menu
Digital TV: Select info bar for the current programme, teletext: select next page;
Direction button : Move down in menu
Digital TV: Select info bar for the current programme, teletext: select previous page;
Direction button : Move left in menu
Teletext: Call up subpages;
Direction button : Move right in menu
Teletext: Call up subpages
26) BACK: Go one level back in menus
27)
TV
: Switch to TV operation/call up information on channel-specific button functions .
5.3.1. Programming the multifunction buttons and
The and buttons can be programmed to any channel position or a particular input source
Start by selecting the function you require and then hold down the corresponding button for 5
seconds until MY BUTTON IS SET appears on the screen. This confirms the new programming.
After each INITIAL INSTALLATION your customised button programming is deleted
and reset to the factory defaults
15
EN

6. Using the device for the first time
Before using for the first time, be sure to read the section “Safety instructions”.
6.1. Unpacking
• Select a suitable place for setting up the device before unpacking.
• Open the box very carefully to avoid damaging the device. The device could be damaged if you
use a knife with a long blade to open the box.
• The box contains a number of small items (including batteries). Keep these out of the reach of
children as they represent a choking hazard.
• Store the packaging material in a safe place; only use this box to transport the TV.
DANGER!
Risk of suffocation!
Packaging film can be swallowed or used improperly. Therefore, there is a risk of
suffocation!
Keep packaging material such as plastic film or plastic bags away from children.
6.2. Mounting
Attach the stand as shown in the illustration. Carry out this step before connecting the smart TV.
4 x
12
3
4 x
4
16

6.3. Inserting batteries in the remote control
Loose the screw of the battery compartment cover on the back of the remote control and re-
move the cover.
Insert two LR03 (AAA) 1.5 V batteries in the battery compartment of the remote control. Check
the battery polarity (inscribed on the bottom of the battery compartment).
Close the battery compartment by fixing the cover with the screw.
NOTICE!
Risk of damage!
The remote control can be damaged by leaking batteries if not used for a long pe-
riod of time!
Remove the batteries from the remote control if the device is not going to be
used for a long period.
6.4. Connecting the antenna
Your smart TV supports different antenna signals.
You can feed the following picture signals via the connection labelled ANT.:
• via analogue cable/an analogue house antenna,
• via a DVB-T/ DVB-T 21antenna or
• via a DVB-C2connector (digital cable)
Connect the antenna cable from either the house aerial/the analogue cable connection, the
DVB-T antenna or the DVB-C connection to the antenna connection on the smart TV
1This service must be available in your region.
17
EN

You also have the option of connecting a digital satellite system to the connection labelled LNB.
Screw the F connector of a coaxial antenna cable onto the connection on the smart TV.
To receive encrypted/subscription channels you will need to use a CI module and
an appropriate card. Insert a CI module (available in specialist shops) into the slot
provided for this purpose on the left-hand side of the device (Common Interface).
You can then insert the card from your provider into the CI module.
6.5. Connecting the power supply
Connect the mains plug on the device to an easily accessible 220 - 240 V ~ 50 Hz mains socket.
6.6. Switching the smart TV on and off
Set the power switch on the bottom of the device to ON. The device switches to standby mode
and the display on the front will light up.
To switch on the device, press
− on the remote control: the Standby/On button , one of the number buttons or one of the
P/+ buttons;
− on the device: the multifunction button .
Use the Standby/On button on the remote control to switch the device back into standby
mode. Although the device has been switched off, it will continue to consume electricity.
Use the mains switch to turn off the device (OFF position). The device will continue to consume
power as long as it is connected to the mains network.
If the device is not receiving an input signal, it will automatically switch to stand-
by mode after five minutes. A countdown timer will appear on the screen until this
time. This function is not available for all sources.
6.7. Channel search when switching on for the first time
When you switch the device on for the first time, you will be guided through the FIRST TIME INSTAL
LATION menu.You can call up and carry out the first-time installation again at any time via the menu
INSTALLATION > FIRST TIME INSTALLATION .
First time installation
Velkommen, vælg venligst et sprog! Dansk
Willkommen, Wählen Sie bitte Ihre Sprache aus! Deutsch
Tere tulemast, palun valige oma keel! Eesti
Welcome please select your language! English
Bienvenido, seleccione un idioma Español
Καλώς ήλΘατε, παρακαλούμε επιλέξτε τη γλώσσα σας! Ελληνικά
Bienvenue !Veuillez choisir une langue. Français
Fáilte roghnaigh do theanga, led‘ thoil! Gaeilge
Dobro došli, molim izaberite svoj jezik! Hrvatski
Benvenuti, Selezionate la vostra luingua! Italiano
Esiet sveicināts, lūdzu, izvlts. savu vald.! Latviešu
Sveiki! Pasirinkite savo kalbą Lietuvių k.
Select language Set language
OK
You can move up or down in the menu and select the required language using the direction but-
tons .
After confirming the selected language with OK the initial installation will begin
18

First time installation
Country
Scan Encrypted Channels
Select favourite network type
Select Broadcast Type:
Digital Aerial
Digital Cable
Satellite
Analogue
Welcome!
Navigate Continue
Choose your country OK Back
BACK
Germany
On
None
Off
Off
Off
Off
Use  to select the desired country. The country setting will influence the order in which the
channels are stored. Also, there are a number of options preset for the individual countries.
If Siyou would also like to search for encrypted channels, set the option to ON.
Now use the direction buttons  to select the preferred reception type: DIGITAL AERIAL, DIGI
TAL CABLE, SATELLITE or ANALOGUE. This reception mode will set to ON in the corresponding op-
tions. After the channel scan, the preferred reception type will be activated.
If you want to activate other reception types, use the direction buttons  to select the recep-
tion type DIGITAL AERIAL, DIGITAL CABLE, SATELLITE or ANALOGUE and then use  to select ON
for the desired reception type.
Afterwards, press OK to continue.
Depending on the model of your TV and the country selection PRIVACY SETTINGS menu may ap-
pear at this point. Using this menu you can set your privacy privileges. Highlight a feature and
use and directional buttons to enable or disable. Read the related explanations displayed
on the screen for each highlighted feature before making any changes. You can use P +/- but-
tons to scroll up and down to read the entire text. You will be able to change your preferences at
any time later from the SETTINGS > PRIVACY SETTINGS menu. If the INTERNET CONNECTION option is
disabled NETWORK/INTERNET SETTINGS screen will be skipped and not displayed. If you have any
questions, complaints or comments regarding this privacy policy or its enforcement, please con-
tact by email at [e-mail].
Now a query appears asking whether you want to make network/Internet settings. Select NO if
you want to skip this step. If you have selected NO here, you cannot subsequently use any net-
work/Internet/HbbTV services.
6.7.1. Network/Internet settings
Network/Internet Settings
Network Type
PressWPS on your wifi router
Internet Speed Test
Advanced Settings
Wake On
Connected
48:6d:bb:b0:dc:65
Navigate
Continue Change Value
OK Back
BACK Skip
Wireless Device
OK
OK
OK
On
Wi-Fi
Delete SavedWifi Profile
19
EN

Network settings
NETWORK TYPE Here you select the network type: WIRELESS DEVICE or WIRED DEVICE. After
making a selection with the direction buttons  and confirming with the
OK button, an overview of all available networks appears. Make a selection
and confirm with the OK button. If a password is required for a network, a vir-
tual keyboard appears which you can use to enter this with the help of the di-
rection buttons  and the OK button. After entering the password,
select OK on the keyboard and confirm with the OK button.
PRESS WPS ON
YOUR WIFI ROUT
ER
(only for WLAN)
This option enables you to quickly establish a WPS connection via a wireless
network (Wi-Fi). Hold down the WPS button on your router and confirm this
option OK using the OK button. Then the WPS connection will be made.
INTERNET SPEED
TEST
Press the OK button in order to test the Internet speed.
ADVANCED SET
TINGS
Press the OK button to call up further network configuration options.
CONFIGURATION Choose the setting AUTOMATIC IP or MANUAL IP. If
you select MANUAL IP, three additional lines appear
in which you can manually enter the data for the IP
ADRESS, SUBNET MASK and DEFAULT GATEWAY using the
direction buttons  and the number buttons.
CONFIGURATION Select here between AUTOMATIC DNS or MANUAL DNS.
If you select MANUAL DNS, two additional lines appear
in which you can manually enter the data for the DNS
SERVER 1 and DNS SERVER 2 using the direction buttons
 and the number buttons.
An existing network connection can be terminated by pressing
the red button.
WAKE ON Activate/deactivate the Wake-On LAN/Wake-On Wireless LAN function (WoL/
WoWLAN). This enables you to switch on the smart TV via a different device
(e.g. a smartphone with the MEDION® Life Remote App). Both devices must be
connected to the same network via LAN or Wi-Fi for this purpose. Select the
ON setting to activate this function. The device being used as a remote con-
trol needs to be connected to the TV once when it is switched on. The control
function only works when the TV is in standby mode. If the TV is turned off
and on again at the mains switch, the connection between the two devices
will be automatically restored.
Exit the network settings by pressing OK.
After exiting the network settings, the channel search will start for your previously selected pre-
ferred reception type. Also pay attention to any other information that is displayed on the screen
depending on your selection.
20