Aquion EFP10 Manual

© 2013 Aquion, Inc. OM-EFP-Rev2013.04
EN Installation & Operating Instructions
UNDER
-
SINK
DRINKING WATER FILTRATION SYSTEM
EFP
SERIES

WARNING & SAFETY INSTRUCTIONS
EN - English Page 2
Table of content & Installation record..................................................................................Page 3
Warning & Safety instructions..............................................................................................Page 4
Operating conditions & Requirements .................................................................................Page 5
Installation ...........................................................................................................................Page 6
Start-up................................................................................................................................Page 8
Maintenance........................................................................................................................Page 9
For future reference, fill in the following data
INSTALLATION RECORD
Serial number: _______________________________________________
Model: EFP10 EFP20
EFP30 EFP30-Plus
Date of installation: _________________________________________
Company name: _____________________________________________
Installer name: ______________________________________________
Phone number: ______________________________________________
TRACKING - FILTER CARTRIDGE REPLACEMENT
Date: __________________ Date: ____________________
Date: __________________ Date: ____________________
Date: __________________ Date: ____________________
Date: __________________ Date: ____________________
Date: __________________ Date: ____________________
Date: __________________ Date: ____________________
Date: __________________ Date: ____________________
Date: __________________ Date: ____________________
Date: __________________ Date: ____________________
Date: __________________ Date: ____________________
Date: __________________ Date: ____________________
Date: __________________ Date: ____________________

OPERATING CONDITIONS & REQUIREMENTS
Page 3 EN - English
Before you begin the installation of the water filtration system, we
advise you read and carefully follow the instructions contained in this
manual. It contains important information about safety, installation, use
and maintenance of the product. The actual system that you have
received, may differ from the pictures/illustrations/descriptions in these
Instructions.
Failure to follow the instructions could cause personal injury or damage
to the appliance or property. Only when installed, commissioned and
serviced correctly, the water filtration system will offer you many years
of trouble-free operation.
The water filtration system is intended to improve the taste and to
safeguard the quality of safe-to-drink potable cold water. Do not use it
to treat water that is microbiologically unsafe or of unknown quality. It
will not purify heavily polluted water or make it safe to drink!
Installation of the water filtration system should only be undertaken by
a competent person, aware of the local codes in force. All plumbing
connections must be done in accordance with local codes.
Before setting up the water filtration system, make sure to check it for
any externally visible damage; do not install or use when damaged.
Keep these Instructions in a safe place and ensure that new users are
familiar with the content.
The water filtration system is designed and manufactured in accordance
with current safety requirements and regulations. Incorrect repairs can
result in unforeseen danger for the user, for which the manufacturer
cannot be held responsible. Therefore repairs should only be
undertaken by a competent technician, familiar and trained for this
product.
In respect of the environment, refer to national/local laws and codes for
correct recycling of this water filtration system.

INSTALLATION
EN - English Page 4
OPERATING PRESSURE: min. 1,4 / max. 6,0 bar
check water pressure regularly.
take into account that night time water pressure may be
considerably higher than day time water pressure.
install a pressure reducer ahead of the water filtration
system if necessary.
OPERATING TEMPERATURE: min. 2 / max. 45 °C
do not install the water filtration system in an environment
where high ambient temperatures or freezing temperatures
can occur.
the water filtration system cannot be exposed to outdoor
elements, such as direct sunlight or atmospheric precipitation.

INSTALLATION
Page 5 EN - English
WATER SUPPLY ADAPTOR
An adaptor is supplied with the water filtration system
for the connection to the water supply inside the house; at
the inlet side (connection to the plumbing inside the house)
it has a 3/8” BSP female thread; the corresponding thread
on the plumbing inside the house should be 3/8” BSP male.
For filter cartridge replacement, the water supply to the
water filtration system needs to be turned off; therefore it
is recommended to install the water supply adaptor behind
a stop valve. Typically this can be the stop valve that is
already in place to shut off the cold water supply to the
main faucet. If the water supply adaptor can not be
installed after this stop valve, we strongly recommend to
install a separate stop valve (not included with this
product!), preferably with 3/8” BSP male thread at the
outlet.
Make sure to shut off the water supply to the place of
installation, before you start any plumbing work.
AFTER EXISTING STOP VALVE IN COLD WATER SUPPLY TO
MAIN FAUCET
1. Remove the existing connection coming from the main
faucet from the outlet of the stop valve.
2. Install an appropriate T-adaptor (preferably with 3/8”
BSP male thread, for connection of the water supply
adaptor) at the outlet of the stop valve.
3. Reinstall the connection coming from the main faucet to
one of the outlets of the T-adaptor.
4. Screw the water supply adaptor onto the other outlet of
the T-adaptor; make sure the gasket is installed inside
the female thread of the water supply adaptor. Tighten
the water supply adaptor.
WITH SEPARATE STOP VALVE (not included)
1. Install an appropriate stop valve in the cold water line
underneath the sink, preferably with 3/8” BSP male
thread at the outlet.
2. Screw the water supply adaptor onto the outlet of the
stop valve; make sure the gasket is installed inside the
female thread of the water supply adaptor. Tighten the
water supply adaptor.
FILTER HOUSING UNIT
Mount the filter housing unit in vertical position.
Fix the filter housing unit against a solid surface only
(f.e. wooden wall of kitchen cabinet), using suitable
mounting screws (not included with this product!).
Make sure to leave minimum 30 mm clearance below
the filter housing unit, to allow for easy removal of the
filter sump during filter cartridge replacement.
Make sure to leave minimum 75 mm clearance at
either side of the filter housing unit, to allow for easy
tubing connections.
The filter housing unit has an integrated mouting
bracket at both sides, so it may be rotated 180° depending
on the optimal setup of the inlet (supply of untreated
water) and outlet (to filtered water faucet) at the specific
place of installation.
1. Select an appropriate location under the sink for the
installation of the filter housing unit.
2. Mark the location of the mounting screw(s) (1x for single
sump models, 2x for double sump models).
3. Install the mounting screw(s).
4. Install the filter housing unit.
5. Tighten the mounting screw(s).
FAUCET
Install the faucet on a flat surface to assure secure
installation and adequate sealing between the faucet and
the counter top.
Use the appropriate tools (drilling machine, drill bit)
and procedures to make the hole in the counter top.
Contact a professional if necessary, to avoid damage to the
counter top.
Make sure the faucet does not hinder the correct
functioning of any other ‘device’ on top of the counter top
(f.e. main faucet, window,…)
Make sure to leave minimum 100 mm clearance under
the counter top, to allow for easy installation of the faucet.
Refer to the assembly diagram included with the faucet
for correct assembly of the faucet.
1. Select an appropriate location for the installation of the
faucet.
2. Drill a hole (with diameter of min. 12 mm – max. 15 mm)
in the counter top.
3. Lower the faucet body through the hole in the counter
top; make sure the o-ring is properly installed in the
faucets base.
4. From underneath the counter top, install the washers
and locking nut over the threaded stud of the faucet
body; tighten the locking nut.
5. Screw the faucet’s spout onto the faucets body.

INSTALLATION
EN - English Page 6
TUBING CONNECTIONS
While the polytubes may be shortened, make sure to
allow enough slack in the tubing for easy installation and
removal of the filter housing unit.
If the polytube needs to be shortened, make sure to cut
it squarely, using a cutter or sharp knife; always inspect the
end of the polytube to make sure there are no
imperfections; remove any blur or flash, or cut again if
necessary.
When bending the polytube, make sure not to over-
bend, as this may result in pinching-off and/or leaking
connections.
COLD WATER SUPPLY TO WATER FILTRATION SYSTEM
(WHITE POLYTUBE - ⅜”)
1. Insert one end of the polytube in the Push-Fit
connection of the water supply adaptor; make sure to
push it in all the way; slightly pull on the polytube to
verify the engagement.
2. Insert the other end of the polytube in the Push-Fit
connection at the inlet of the water filtration system;
make sure to push it in all the way; slightly pull on the
polytube to verify the engagement.
WATER FILTRATION SYSTEM TO FAUCET
(BLUE POLYTUBE - ¼”)
1. Insert the polytube, that is attached to the faucet, in the
Push-Fit connection at the outlet of the water filtration
system; make sure to push it in all the way; slightly pull
on the polytube to verify the engagement.
FILTER CARTRIDGE(S)
Remove the plastic protective film from the filter
cartridge before installing it in the water filtration system.
Once the plastic protective film is removed from the
filter cartridge, we recommend to install the filter cartridge
in the water filtration system as soon as possible, to avoid
accidental damage or contamination of the filter cartridge.
Filter cartridges with a central opening at both sides
(Double-Open-End) don’t have a specific top or bottom, so
they can be installed either way. Filter cartridges with only
1 central opening (Single-Open-End), must be installed with
the opening at the top.
For double sump systems (EFP30-Plus) only: the spun
polypropylene filter cartridge serves as pre-filter, so it must
be installed in the the filter sump closest to the inlet of the
water filtration system.
1. Unscrew the filter sump from the filter manifold by
rotating the filter sump to the left.
2. Inspect the inside of the filter sump; make sure it is clean
and no impurities are present; clean and rinse
thoroughly if necessary.
3. Insert the filter cartridge in the filter sump; make sure
the supplied gasket is properly installed at the top
(Double-Open-End and Single-Open-End) and bottom
(Double-Open-End).
4. Verify that the filter sump o-ring is still correctly
positioned in the o-ring groove inside the top of the filter
sump.
5. With the filter cartridge nicely centered inside the filter
sump, hold the filter sump up to the filter manifold, so
the central opening in the top of the filter cartridge is
aligned with the centering guide on the filter manifold.
6. Screw the filter sump onto the filter manifold by rotating
the filter sump to the right; tighten it firmly by hand; the
filter sump should tighten up to the filter manifold.

START-UP
Page 7 EN - English
PRESSURIZING
1. Open the filtered water faucet.
2. Gently open the water supply to the water filtration
system to allow the water filtation system to be purged
and filled up with water.
3. As soon as water starts to flow from the faucet, close the
faucet.
4. Check the water filtation system and all tubing
connections for leaks. If any leaks are observed, shut off
the water supply and open the faucet immediately.
RINSING
The water filtration system uses a filter cartridge
containing activated carbon. At first use some discoloration
of the filtered water will occur. This is totally harmless and
will disappear after proper rinsing!
At first use the filtered water may be slightly non-
transparent (milky appearance) when it flows from the
faucet; this is caused by oxygen inside the filter cartridge,
that is dissolved in the filtered water. This is totally
harmless and will disappear after proper rinsing!
1. Open the filtered water faucet and let the water run for
5 minutes to rinse the activated carbon filter cartridge.
2. Close the faucet.

MAINTENANCE
EN - English Page 8
ROUTINE CHECKS
Regularly the user should visually check the water filtration
system for leaks. Shut off the water supply and open the
faucet immediately if any leaks are observed.
FILTER CARTRIDGE REPLACEMENT
The replacement frequency of the filter cartridge
depends on the water quality and water consumption. In
practice, for a typical residential application, the filter
cartridge should be replaced every 6 to 12 months.
When the water flow from the filtered water faucet
noticeably slows down, this may be caused by the filter
cartridge becoming clogged by impurities. Replacement of
the filter cartridge is recommended.
The filter cartridge replacement procedure may be
performed with the filter housing unit installed under the
sink. However it might be more convenient to remove the
tubing from the filter housing unit and to remove the filter
housing unit from underneath the sink.
Remove the plastic protective film from the filter
cartridge before installing it in the water filtration system.
Once the plastic protective film is removed from the
filter cartridge, we recommend to install the filter cartridge
in the water filtration system as soon as possible, to avoid
accidental damage or contamination of the filter cartridge.
Filter cartridges with a central opening at both sides
(Double-Open-End) don’t have a specific top or bottom, so
they can be installed either way. Filter cartridge with only 1
central opening (Single-Open-End), must be installed with
the opening at the top.
REPLACEMENT PARTS
Model
Filter cartridge
PN
EFP10
Activated Carbon Block (5
µm)
74147
EFP20
Activated Carbon Block (0,2 µm)
74148
EFP30
3
-
in
-
1: spun PP
-
Activated Carbon
Block-Hollow Fibre (0,1 µm)
74149
EFP30
-
Plus
Spun PP (5 µm) prefilter
74146
3
-
in
-
1: spun PP
-
Activated Carbon
Block-Hollow Fibre (0,1 µm)
74149
1. Close the water supply to the water filtration system.
2. Open the filtered water faucet to release the water
pressure. As soon as water stops to flow from the faucet,
close the faucet.
3. Place a recipient underneath the filter sump, to catch
any spilled water.
4. Unscrew the filter sump from the filter manifold by
rotating the filter sump to the left.
5. Inspect the inside of the filter sump; make sure it is clean
and no impurities are present; clean and rinse
thoroughly if necessary.
6. Insert the filter cartridge in the filter sump; make sure
the supplied gasket(s) are properly installed at the top
(Double-Open-End and Single-Open-End) and bottom
(Double-Open-End).
7. Verify that the filter sump o-ring is still correctly
positioned in the o-ring groove inside the top of the filter
sump.
8. With the filter cartridge nicely centered inside the filter
sump, hold the filter sump up to the filter manifold, so
the center hole in the top of the filter cartridge is aligned
with the centering guide on the filter manifold.
9. Screw the filter sump onto the filter manifold by rotating
the filter sump to the right; tighten it firmly by hand; the
filter sump should tighten up to the filter manifold.
10. Follow the START-UP procedure as previously described
in these Instructions.
SANITIZING THE WATER FILTRATION SYSTEM
Whenever heavily polluted water or water of
microbiologically unknown quality is passed through the
water filtration system, we strongly recommend to
replace the filter cartridge(s), clean the filter sump(s) and
thoroughly rinse the water filtration system.
This water filtration system is manufactured from premium
quality material and assembled in safe conditions to assure it
is clean and sanitary. If installed and serviced correctly, this
water filtration system will not infect or contaminate your
water supply. However, as in any 'device' plumbed-in in your
water distribution system, a proliferation of bacteria is
possible, especially in case of 'stagnant water'.
If the water supply to the water filtration system is
disconnected, or in case of long-term non use of the water
filtration system, we recommend to rinse the water filtration
system before putting it into use:
1. Open the filtered water faucet and let the water run for
10 minutes to rinse the water filtration system.
2. Close the faucet.

Page 9 EN - English

EN - English Page 10

Page 11 EN - English

AQUION, INC.
Lammerdries-Oost 30c
B-2250 Olen
Belgium
+32 (0) 14-28.51.71
+32 (0) 14-28.51.70
RPR/RPM Turnhout
BWT/TVA/VAT BE 0882.738.206
[email protected]
www.eriewatertreatment.com