Arada MaxR-3210 User manual

ARADA, Inc.
1024 Morse Avenue,
Sunnyvale,
CA 94089
Arada Systems Inc.,
1024 Morse Avenue,
Sunnyvale, CA - 94089.
Tel: [phone]
www.aradasystems.com
Arada Systems, Inc.
MaxR-3210 Single Band Wireless-N Access Point
User Manual
This document helps you to configure and use the
MaxR-3210 Single Band Wireless-N Access Point
Dec 2009
Book Version: 1.1

ii
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.

Contents
About This Manual
Conventions, Formats, and Scope .....................................................................................i
Chapter 1
Introduction
About the MaxR-3210 Single Band Wireless-N Access Point ........................................1-1
Key Features and Standards ..........................................................................................1-1
Supported Standards and Conventions ...................................................................1-2
Key Features ............................................................................................................1-2
802.11b/g/n Standards-based Wireless Networking ................................................1-4
Autosensing Ethernet Connections with Auto Uplink ...............................................1-4
System Requirements ....................................................................................................1-4
What’s In the Box? .........................................................................................................1-5
Hardware Description .....................................................................................................1-5
Rear Panel ...............................................................................................................1-5
Chapter 2
Basic Installation and Configuration
Wireless Equipment Placement and Range Guidelines .................................................2-2
Understanding MaxR-3210 Wireless Security Options ..................................................2-3
Installing the MaxR-3210 Wireless Access Point ...........................................................2-4
Setting up the MaxR-3210 Wireless Access Point ...................................................2-4
Configuring LAN and Wireless Access ....................................................................2-4
Configuring Time Settings .................................................................................2-7
Configuring Wireless Access .............................................................................2-9
Deploying the MaxR-3210 Wireless Access Point ...................................................2-9
Verifying Wireless Connectivity ..............................................................................2-10
Logging In Using the Default IP Address ......................................................................2-10
Setting Basic IP Options ...............................................................................................2-11
Wireless Settings ..........................................................................................................2-13
Configuring 802.11b/bg/ng Wireless Settings ........................................................2-13

MaxR-3210 Wireless-N Access Point User Manual
iv Arada Systems Confidential
v1.1, Dec 2009
Configuring Basic QoS Settings .............................................................................2-16
Setting Up and Testing Basic Wireless Connectivity ....................................................2-17
Understanding Security Profiles ...................................................................................2-18
SSID and WEP/WPA Settings Setup Form ..................................................................2-22
802.11b/bg/ng Configuration ............................................................................2-22
Configuring the RADIUS Server Settings .....................................................................2-23
Setting up a Security Profile .........................................................................................2-25
Configuring WEP ..........................................................................................................2-27
Configuring WPA with RADIUS ....................................................................................2-29
Configuring WPA2 with RADIUS ..................................................................................2-31
Configuring WPA and WPA2 with RADIUS ..................................................................2-32
Configuring WPA-PSK ..................................................................................................2-34
Configuring WPA2-PSK ................................................................................................2-35
Configuring WPA-PSK and WPA2-PSK ........................................................................2-36
Restricting Wireless Access by MAC Address .............................................................2-38
Chapter 3
Management
Remote Management .....................................................................................................3-1
Remote Console .............................................................................................................3-3
Using the Secure Telnet Interface ............................................................................3-3
CLI Commands ........................................................................................................3-4
Upgrading the Wireless Access Point Software .............................................................3-5
Configuration File Management .....................................................................................3-6
Saving Your Configuration Settings .........................................................................3-7
Restoring Saved Settings .........................................................................................3-7
Restoring the MaxR-3210 to the Factory Default Settings .......................................3-8
Changing the Administrator Password .........................................................................3-10
Enabling the SysLog Server .........................................................................................3-11
Using Activity Log Information ......................................................................................3-12
Viewing General Summary Information ........................................................................3-12
Viewing Network Traffic Statistics .................................................................................3-14
Viewing Available Wireless Station Statistics ................................................................3-16
Enabling Rogue AP Detection ......................................................................................3-17
Importing Rogue AP List from a File ......................................................................3-18
Viewing Rogue AP Statistics ........................................................................................3-19

MaxR-3210 Wireless-N Access Point User Manual
Arada Systems Confidential v
v1.1, Dec 2009
Packet Capture .............................................................................................................3-21
Chapter 4
Advanced Configuration
IP Settings for Wireless Clients ......................................................................................4-1
Hotspot Settings .............................................................................................................4-3
Configuring Advanced Wireless Settings .......................................................................4-4
Configuring 802.11b/bg/ng Advanced Wireless Settings .........................................4-4
Configuring Advanced QoS Settings ..............................................................................4-6
Enabling Wireless Bridging .............................................................................................4-8
Configuring an MaxR-3210 as a Point-to-Point Bridge ..........................................4-12
Configuring an MaxR-3210 as a Point-to-Multi-Point Wireless Bridge ...................4-13
Chapter 5
Troubleshooting and Debugging
No lights are lit on the Access Point. ..............................................................................5-1
The Wireless LAN activity light does not light up. ...........................................................5-1
The LAN light is not lit. ....................................................................................................5-2
I cannot access the Internet or the LAN with a wireless capable computer. .................5-2
I cannot connect to the MaxR-3210 to configure it. ........................................................5-3
When I enter a URL or IP address I get a timeout error. ................................................5-3
Using the Reset Button to Restore Factory Default Settings ..........................................5-4
Appendix A
Default Settings and Technical Specifications
Factory Default Settings ................................................................................................ A-1
Technical Specifications ................................................................................................. A-3
Appendix B
Command Line Reference
Command Sets .............................................................................................................. B-1
Index

MaxR-3210 Wireless-N Access Point User Manual
vi Arada Systems Confidential
v1.1, Dec 2009

Arada Systems Confidential i
v1.1, Dec 2009
About This Manual
The MaxR-3210 Single Band Wireless-N Access Point User Manual describes how to install,
configure and troubleshoot the MaxR-3210 Wireless Access Point. The information in this manual
is intended for readers with intermediate computer and Internet skills.
Conventions, Formats, and Scope
The conventions, formats, and scope of this manual are described in the following paragraphs:
•Typographical Conventions.This manual uses the following typographical conventions:
•Formats.This manual uses the following formats to highlight special messages:
Italic Emphasis, books, CDs, file and server names, extensions
Bold User input, IP addresses, GUI screen text
Fixed Command prompt, CLI text, code
italic URL links
Note: This format is used to highlight information of importance or special interest.
Tip: This format is used to highlight a procedure that will save time or resources.
Warning: Ignoring this type of note may result in a malfunction or damage to the
equipment.

MaxR-3210 Wireless-N Access Point User Manual
ii Arada Systems Confidential
v1.1, Dec 2009
Danger: This is a safety warning. Failure to take heed of this notice may result in
personal injury or death.

Arada Systems Confidential 1
v1.1, Dec 2009
Chapter 1
Introduction
This chapter describes some of the key features of the MaxR-3210 Single Band Wireless-N Access
Point. It also includes the minimum prerequisites for installation (“System Requirements” on
page 1-4.), package contents (“What’s In the Box?” on page 1-5) and a description of the front and
back panels of the MaxR-3210 (“Hardware Description” on page 1-5).
About the MaxR-3210 Single Band Wireless-N Access Point
The MaxR-3210 Single Band Wireless-N Access Point is the basic building block of a wireless
LAN infrastructure. It provides connectivity between Ethernet wired networks and radio-equipped
wireless notebook systems, desktop systems, print servers, and other devices.
The MaxR-3210 provides wireless connectivity to multiple wireless network devices within a
fixed range or area of coverage—interacting with a wireless network interface card (NIC) via an
antenna. Typically, an individual in-building access point provides a maximum connectivity area
of about a 500 foot radius. Consequently, the MaxR-3210 Single Band Wireless-N Access Point
can support a small group of users in a range of several hundred feet. Most access points can
handle between 10 to 30 users simultaneously per radio.
The MaxR-3210 Single Band Wireless-N Access Point acts as a bridge between the wired LAN
and wireless clients. Connecting multiple MaxR-3210 Wireless Access Points via a wired Ethernet
backbone can further lengthen the wireless network coverage. As a mobile computing device
moves out of the range of one access point, it moves into the range of another. As a result, wireless
clients can freely roam from one Access Point to another and still maintain seamless connection to
the network.
Key Features and Standards
The MaxR-3210 Wireless Access Point is easy-to-use and provides solid wireless and networking
support. It also offers a wide range of security options.

MaxR-3210 Wireless-N Access Point User Manual
2 Arada Systems Confidential
v1.1, Dec 2009
Supported Standards and Conventions
The following standards and conventions are supported:
•Standards Compliance.The Wireless Access Point complies with the IEEE 802.11b/g/n
standards for Wireless LANs.
•Full WPA and WPA2 support. WPA and WPA2 enterprise-class strong security with
RADIUS and certificate authentication as well as dynamic encryption key generation.WPA-
PSK and WPA2-PSK preshared key authentication without the overhead of RADIUS servers
but with all of the strong security of WPA.
•Multiple BSSIDs. Supports multiple BSSIDs. When a Access Point is connected to a wired
network and a set of wireless stations, it is called a Basic Service Set (BSS). The Basic Service
Set Identifier (BSSID) is a unique identifier attached to the header of packets sent over a
WLAN that differentiates one WLAN from another when a mobile device tries to connect to
the network.
The multiple BSSID feature allows you to configure up to 8 SSIDs on your MaxR-3210 access
point and assign different configuration settings to each SSID. All the configured SSIDs are
active and the network devices can connect to the access point by using any of these SSIDs.
•DHCP Client Support. DHCP provides a dynamic IP address to PCs and other devices upon
request. The MaxR-3210 can act as a client and obtain information from your DHCP server; it
can also act as a DHCP server and provide network information for wireless clients.
•SNMP Support. Support for Simple Network Management Protocol (SNMP) Management
Information Base (MIB) management.
• 802.1Q VLAN (Virtual LAN) Support. A network of computers that behave as if they are
connected to the same network even though they actually may be physically located on
different segments of a LAN. VLANs are configured through software rather than hardware,
which makes them extremely flexible. VLANs are very useful for user/host management,
bandwidth allocation and resource optimization.
Key Features
The MaxR-3210 provides solid functionality, including the following features:
•2.4Ghz Band Operating Frequency. The Wireless Access Point operates in the 2.4 GHz
frequency band.
• Multiple operating modes:
– Wireless Access Point. Operates as a standard 802.11b/bg/ng access point.

MaxR-3210 Wireless-N Access Point User Manual
Arada Systems Confidential 3
v1.1, Dec 2009
– Point-to-Point Bridge. In this mode, the MaxR-3210 only communicates with another
bridge-mode wireless access point (with or without clients). Network authentication
should be used to protect this communication.
– Point-to-Multi-Point Bridge. Select this only if this MaxR-3210 is the “Master” for a
group of bridge-mode wireless access points. The other bridge-mode wireless access
points send all traffic to this “Master”, and do not communicate directly with each other.
Network Authentication should be used to protect this traffic.
• Hotspot Settings. You can allow the first HTTP (TCP, port 80) request, on client association,
to be captured and redirected to the URL you specify.
•Upgradeable Firmware. Firmware is stored in a flash memory and can be upgraded easily,
using only your Web browser, and can be upgraded remotely. In addition to using Web
browser to do so, command-line interface and SNMP can also be used.
•Rogue AP detection. The Rogue AP detection feature shows a list of unknown APs to the
administrator.
•Access Control. The Access Control MAC address filtering feature can ensure that only
trusted wireless stations can use the MaxR-3210 to gain access to your LAN.
•Security Profiles. When using multiple BSSIDs, you can configure unique security settings
(encryption, SSID, etc.) for each BSSID.
•Hidden Mode. The SSID is not broadcast, assuring only clients configured with the correct
SSID can connect.
•Secure Telnet Command Line Interface. The secure Telnet command line interface enables
direct secure access over the serial port and easy scripting of configuration of multiple MaxR-
3210s across an extensive network via the Ethernet interface. An SSH client is required.
•Configuration Backup. Configuration settings can be backed up to a file and restored.
•Power over Ethernet. Power can be supplied to the MaxR-3210 over the Ethernet port from
any 802.3af compliant mid-span or end-span source.
•Autosensing Ethernet Connection with Auto Uplink Interface. Connects to 10/100/1000
Mbps IEEE 802.3 Ethernet networks.
•LED Indicators. Power/Test, LAN speed, LAN activity, and wireless activity for each radio
mode are easily identified.
• Wireless Multimedia (WMM) Support. WMM is a subset of the 802.11e standard. WMM
allows wireless traffic to have a range of priorities, depending on the kind of data. Time-
dependent information, like video or audio, has a higher priority than normal traffic. For
WMM to function correctly, Wireless clients must also support WMM.

MaxR-3210 Wireless-N Access Point User Manual
4 Arada Systems Confidential
v1.1, Dec 2009
• WMM Power Save Support. Power Save uses mechanisms from 802.11e and legacy 802.11
to save power (for battery powered equipment) and fine-tune power consumption.
• VLAN Security Profiles. Each Security Profile can be assigned a VLAN ID as each Security
Profile is modified.
802.11b/g/n Standards-based Wireless Networking
The MaxR-3210 Single Band Wireless-N Access Point provides a bridge between Ethernet wired
LANs and 802.11b/g/n compatible wireless LAN networks. It provides connectivity between
Ethernet wired networks and radio-equipped wireless notebook systems, desktop systems, print
servers, and other devices. Additionally, the MaxR-3210 supports the following wireless features:
• Aggregation Support
• Reduced Inter Frame Spacing support
• Multiple Input, Multiple Output (MIMO) support
• Distributed coordinated function (CSMA/CA, Back off procedure, ACK procedure,
retransmission of unacknowledged frames)
• RTS/CTS handshake
• Beacon generation
• Packet fragmentation and reassembly
• Auto or long preamble
• Roaming among access points on the same subnet
Autosensing Ethernet Connections with Auto Uplink
The MaxR-3210 can connect to a standard Ethernet network. The LAN interface is autosensing
and capable of full-duplex or half-duplex operation.
The access point incorporates Auto UplinkTM technology. The Ethernet port will automatically
sense whether the Ethernet cable plugged into the port should have a “normal” connection such as
to a computer or an “uplink” connection such as to a switch or hub. That port will then configure
itself to the correct configuration. This feature also eliminates any concerns about crossover
cables, as Auto Uplink will accommodate either type of cable to make the right connection.
System Requirements
Before installing the MaxR-3210, make sure your system meets these requirements:
• A 10/100/1000 Mbps Local Area Network device such as a hub or switch

MaxR-3210 Wireless-N Access Point User Manual
Arada Systems Confidential 5
v1.1, Dec 2009
• The Category 5 UTP straight through Ethernet cable with RJ-45 connector included in the
package, or one like it
• A 100-240 V, 50-60 Hz AC power source
• A Web browser for configuration such as Microsoft Internet Explorer 5.0 or above, or Mozilla
3.0 or above
• At least one computer with the TCP/IP protocol installed
• 802.11b/g/n-compliant devices.
What’s In the Box?
The product package should contain the following items:
• MaxR-3210 Single Band Wireless-N Access Point
• Three Reverse SMA 5dbi dual band dipole antennas.
• Power adapter and cord (12 V dc, 1.5 A)
• Straight through Category 5 Ethernet cable
• RJ-45 to DB-9 female connector.
•Resource CD which includes this manual.
• Support Registration card
Contact your reseller or customer support in your area if there are any missing or damaged parts.
You can refer to the Support Information Card for the telephone number of customer support in
your area. You should keep the Support Information card, along with the original packing
materials, and use the packing materials to repack the MaxR-3210 if you need to return it for
repair.
Hardware Description
This section describes the rear panel hardware functions of the MaxR-3210.
Rear Panel
The MaxR-3210 rear panel functions are described below:
1. Left, Middle, and Right Detachable Antenna
The MaxR-3210 provides three detachable antennas.

MaxR-3210 Wireless-N Access Point User Manual
6 Arada Systems Confidential
v1.1, Dec 2009
2. Restore to Factory Defaults Button
The restore to default button is located next to the RJ-45 console port and restores the MaxR-
3210 to the factory default settings.
3. Serial Console Port
RJ-45 serial console port for serial DTE connections.
4. RJ-45 Ethernet Port
Use the MaxR-3210 Ethernet RJ-45 port to connect to an Ethernet LAN through a device such
as a hub, switch, router, or PoE switch.
5. Power Socket
This socket connects to the MaxR-3210 12V 1.5A power adapter.

Arada Systems Confidential 1
v1.1, Dec 2009
Chapter 2
Basic Installation and Configuration
This chapter describes how to set up your MaxR-3210 Single Band Wireless-N Access Point for
wireless connectivity to your LAN. This basic configuration will enable computers with 802.11b/
g/n wireless adapters to do such things as connect to the Internet, or access printers and files on
your LAN.
This chapter contains the following sections:
1. “Wireless Equipment Placement and Range Guidelines
2. “Understanding MaxR-3210 Wireless Security Options
3. “Installing the MaxR-3210 Wireless Access Point
4. “Logging In Using the Default IP Address
5. “Setting Basic IP Options
6. “Wireless Settings
7. “Setting Up and Testing Basic Wireless Connectivity
8. “Understanding Security Profiles
9. “SSID and WEP/WPA Settings Setup Form
10. “Configuring the RADIUS Server Settings
11. “Setting up a Security Profile
12. “Configuring WEP
13. “Configuring WPA with RADIUS
Note: Indoors, computers can connect over 802.11b/bg/ng wireless networks at ranges of
several hundred feet or more. This distance can allow for others outside your area
to access your network. It is important to take appropriate steps to secure your
network from unauthorized access. The MaxR-3210 Wireless Access Point
provides highly effective security features which are covered in detail in
“Understanding Security Profiles” on page 2-18. Deploy the security features
appropriate to your needs.

MaxR-3210 Wireless-N Access Point User Manual
2 Arada Systems Confidential
v1.1, Dec 2009
14. “Configuring WPA2 with RADIUS
15. “Configuring WPA and WPA2 with RADIUS
16. “Configuring WPA-PSK
17. “Configuring WPA2-PSK
18. “Configuring WPA-PSK and WPA2-PSK
19. “Restricting Wireless Access by MAC Address
You need to prepare these three things before you can establish a connection through your wireless
access point:
• A location for the MaxR-3210 that conforms to the “Wireless Equipment Placement and
Range Guidelines below.
• The wireless access point connected to your LAN through a device such as a hub, switch,
router, or Cable/DSL gateway.
• One or more computers with properly configured 802.11b/g/n wireless adapters.
Wireless Equipment Placement and Range Guidelines
The operating distance or range of your wireless connection can vary significantly based on the
physical placement of the Access Point. The latency, data throughput performance, and notebook
power consumption of wireless adapters also vary depending on your configuration choices.
For best results, place your Access Point:
• Near the center of the area in which your PCs will operate.
• In an elevated location such as a high shelf where the wirelessly connected PCs have line-of-
sight access (even if through walls).
• Away from sources of interference, such as PCs, microwaves, and 2.4 GHz cordless phones.
• Away from large metal surfaces.
Putting the antenna in a vertical position provides best side-to-side coverage. Putting the antenna
in a horizontal position provides best up-and-down coverage.
Note: Failure to follow these guidelines can result in significant performance degradation
or inability to wirelessly connect to the MaxR-3210. For complete performance
specifications, see Appendix A, “Default Settings and Technical Specifications.”

MaxR-3210 Wireless-N Access Point User Manual
Arada Systems Confidential 3
v1.1, Dec 2009
If you are using multiple access points for 11b/bg/ng, it is better if adjacent access points use
different radio frequency channels to reduce interference. The recommended Channel spacing
between adjacent access points is 5 Channels (for example, use Channels 1 and 6, or 6 and 11).
The time it takes to establish a wireless connection can vary depending on both your security
settings and placement. Some types of security connections can take slightly longer to establish
and can consume more battery power on a notebook computer.
Understanding MaxR-3210 Wireless Security Options
Your wireless data transmissions can be received well beyond your walls by anyone with a
compatible adapter. For this reason, use the security features of your wireless equipment. The
MaxR-3210 Wireless Access Point provides highly effective security features which are covered
in detail in this chapter. Deploy the security features appropriate to your needs.
There are several ways you can enhance the security of your wireless network:
•Restrict Access Based on MAC address. You can restrict access to only trusted PCs so that
unknown PCs cannot wirelessly connect to the MaxR-3210. MAC address filtering adds an
obstacle against unwanted access to your network, but the data broadcast over the wireless link
is fully exposed.
•Turn Off the Broadcast of the Wireless Network Name (SSID). If you disable broadcast of
the SSID, only devices that have the correct SSID can connect. This nullifies the wireless
network “discovery” feature of some products such as Windows XP, Vista and Unix systems
but the data is still fully exposed to a determined snoop using specialized test equipment like
wireless sniffers.
•Use WEP. Wired Equivalent Privacy (WEP) data encryption provides data security. WEP
open authentication and WEP data encryption will block all but the most determined
eavesdropper.
•Use WPA or WPA-PSK. Wi-Fi Protected Access (WPA) data encryption provides data
security. The very strong authentication along with dynamic per frame rekeying of WPA make
it virtually impossible to compromise. Because this is a new standard, wireless device driver
and software availability may be limited.
Note: WEP and TKIP provide only legacy rates of operation. So, AES is the
recommended solution to use the 802.11n rates and speed.

MaxR-3210 Wireless-N Access Point User Manual
4 Arada Systems Confidential
v1.1, Dec 2009
Installing the MaxR-3210 Wireless Access Point
Before installing the MaxR-3210 Single Band Wireless-N Access Point, you should make sure that
your Ethernet network is up and working. You will be connecting the access point to the Ethernet
network so that computers with 802.11b/g/n wireless adapters will be able to communicate with
computers on the Ethernet network. In order for this to work correctly, verify that you have met all
of the system requirements, shown on “System Requirements” on page 1-4.
Setting up the MaxR-3210 Wireless Access Point
To set up the MaxR-3210 Wireless Access Point:
1. Prepare a computer with an Ethernet adapter. If this computer is already part of your network,
record its TCP/IP configuration settings.
2. Configure the computer with a static IP address of 192.168.0.210 and 255.255.255.0 for the
Subnet Mask.
3. Connect an Ethernet cable from the MaxR-3210 to the computer.
4. Turn on your computer, connect the power adapter to the MaxR-3210 and verify the
following:
• The PWR power light goes on.
• The LAN light of the Access Point is lit when connected to a powered on computer.
• The WLAN LEDs should be blinking.
Configuring LAN and Wireless Access
To configure the MaxR-3210 Ethernet port for LAN access:
1. Connect to the MaxR-3210 by opening your browser and entering http://192.168.0.237 in the
address field. The MaxR-3210 login screen appears (see Figure 2-1).
2. Enter admin for the user name and password for the password, both in lower case letters.
Tip: Before mounting the MaxR-3210 in a high location, first set up and test the MaxR-
3210 to verify wireless network connectivity.

MaxR-3210 Wireless-N Access Point User Manual
Arada Systems Confidential 5
v1.1, Dec 2009
3. Click Login. The main menu of the MaxR-3210 displays as shown in Figure 2-2.
• When the Access Point is connected to the Internet, under the Support tab, select
Documentation to view the documentation for the Access Point.
• On the top-right of the screen, select Logout to exit the MaxR-3210 setup screens. (You
will automatically be logged out of the Access Point after 5 minutes of no activity.)
4. Access Point Name: Enter the access point name of the MaxR-3210.
This unique name is the access point NetBIOS name. The default Access Point Name is
located on the bottom label of MaxR-3210. The default is aradaxxxxxx, where xxxxxx
represents the last 6 digits of the MaxR-3210 MAC address. You may modify the default name
with a unique name up to 15 characters long.
Figure 2-1 Login screen

MaxR-3210 Wireless-N Access Point User Manual
6 Arada Systems Confidential
v1.1, Dec 2009
5. Select Time from the left panel. The Time screen displays, as shown in Figure 2-2.
6. Enter the Time Settings for your area. See the online help or “Configuring Time Settings” on
page 2-7 for more information about how to configure the settings on this screen.
Figure 2-2 Timezone and system time related settings