Araknis Networks 210 Series User manual

210 SERIES COMPACT NETWORK SWITCHES
Quick Start Guide
AN-210-SW-C-8-PoE

3
210 Series Compact Network Switches
Quick Start Guide
© 2020 Araknis Networks®
FCC Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.
1
2
NOTE: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harm-
ful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on,
the user is encouraged to try to correct the interference by one or more of the following measures.
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
This equipment has been verified to comply with the limits for a class B computing device, pursuant to FCC Rules. In order to maintain
compliance with FCC regulations, shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded
cables is likely to result in interference to radio and TV reception. The user is cautioned that changes and modifications made to the equip-
ment without the approval of manufacturer could void the user’s authority to operate this equipment.

4
210 Series Compact Network Switches
Quick Start Guide
5
210 Series Compact Network Switches
Quick Start Guide
© 2020 Araknis Networks®
CE Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the
user may be required to take adequate measures.
UL Statement
All models have been evaluated by UL.
This device is intended for indoor use only. It should not be connected to an Ethernet network with outside plant
routing.
The user must use the class I optical transceivers which conform to U.S. code of federal regulation, 21 CFR 1040.
This equipment is only to be connected to PoE networks without routing to outside plants.
Ensure the power cord is connected to a socket-outlet with earthing connection, or equivalent.
NOTE: Maximum PoE output power of this equipment is 65W.
Welcome to Araknis Networks™
Thank you for choosing an Araknis 210-series Compact Network Switch. This PoE-powered switch features Gigabit
connectivity on all ports, updated modern aesthetics, and a level of control (Websmart) rarely seen in managed
solutions. The Araknis 210-series switch is a sleek and highly capable addition to any network.
Features
• Gigabit Ethernet
• 8 × 802.3af/at PoE-OUT Ports
• 2 × SFP Uplink 1000BASE-X Ports
• Multi-mounting can design
• Websmart switch
• OvrC enabled
Dimensions (W x H x D)
• 8 Port: 12.71" x 1.50" x 4.13"
Operating Temperature
• 32–122°F (0–50°C)

6
210 Series Compact Network Switches
Quick Start Guide
7
210 Series Compact Network Switches
Quick Start Guide
© 2020 Araknis Networks®
Step 1: Unbox
Switch
Quick Start Guide
Rubber Feet (4) Structured Wiring
Can Mounting Kit
w/ Push Pins (2)
Shelf Mount Kit:
4 sets of:
• Screw: M3 x 8mm
• Hollow Screw: M6 x 8mm
• Nut: M6 nut
4 wall anchors with M3 x
16mm screws
Spare Can Mounting
Push Pins (4)
Body: 8.5mm(D), 10.4mm(L),
6.35mm(W)
Pin: 8.5mm(D), 18.2mm(L),
3.7mm(W)
Step 2: Install
210 compact switches feature several mounting options for easy setup in any scenario. See the following pages for
specific instructions.
Shelf
(use included rubber feet)
Wall Structured Wiring Can
IEC Power Cable

8
210 Series Compact Network Switches
Quick Start Guide
9
210 Series Compact Network Switches
Quick Start Guide
© 2020 Araknis Networks®
Structured Wiring Can Installation
NOTE: The switch can only be mounted to the structured wiring can with the Ethernet ports facing right or left.
Mounting Shelf Installation
(Due to its width, this model should span two mounting shelves. We do not recommend using only one.)
M3 x 4mm screw

10
210 Series Compact Network Switches
Quick Start Guide
11
210 Series Compact Network Switches
Quick Start Guide
© 2020 Araknis Networks®
NOTE: Connect SFP ports using Araknis SFP adapters for RJ45 or multi-mode fiber cables. SFP adapters sold separately.
Step 3: Connect
RESET
1 3 5 7
2 4 6 8
Link/Act1 Gbps
9 SFP 10 SFP
Link/Act
1 Gbps
Computer
Switch
Switch
100–240V AC
Wall Outlet
Router IP Camera
WANLAN
Step 4: PoE Budget
The power budget for delivering Power over Ethernet limits the total number of watts available between all of
the ports (limited to 30W total consumption on each port). Add the total number of watts consumed by all
connected PoE devices to ensure that every thing can be powered, as illustrated in the example below.
Model PoE Budget
AN-210-SW-C-8-POE 65W
AN-210-SW-C-8-POE
Total PoE Device Consumption = 45W
PoE Budget Left Available = 20W
Total PoE Budget Available = 65W
8W + + +8W 12W 14W

12
210 Series Compact Network Switches
Quick Start Guide
13
210 Series Compact Network Switches
Quick Start Guide
© 2020 Araknis Networks®
Step 5: Verify
1. Power LED – On: system is up.
O: system is down.
2. 1Gbps LED – On: port connected at 1Gbps speed.
O: port is connected at 10/100Mbps speed.
3. Link/Act LED – On: port is connected to another device.
Blinking: packets are running through the port.
O: port is not connected to a device.
A
B
C
Step 6: Claim on OvrC
ENABLED
Web Browser
Access
Mobile
Apps
AN-110-SW-R-8
1 2 3 4 5 6 7 8
1 Gbps
Link/Act
OvrC provides remote firmware upgrades, real-time notifications, and intuitive customer management, right from
your computer or mobile device. Setup is plug-and-play, with no port forwarding or DDNS address required. To add
this device to your OvrC account:
Connect the switch to the network (Internet access required).
Log Into OvrC (www.ovrc.com) or load the OvrC app.
Add the device (MAC address and Service Tag numbers needed for authentication).
A
B
C
(RJ-45 LEDs only)

14
210 Series Compact Network Switches
Quick Start Guide
Pro Tip: Rebooting the Switch
Reboot – Press and hold the RESET button on the back of the switch
for 5 seconds, then release. The switch will power cycle and
the front status lights will flash.
Factory Reset – Press and hold the RESET button for 15 seconds until all LEDs
turn solid. The switch will reboot and be reset to factory
default settings.

© 2020 Araknis Networks®
200306-0951
Warning
This product can expose you to chemicals including carbon black, which is known to the State of California
to cause cancer. For more information go to www.P65Warnings.ca.gov.
2-Year Limited Warranty
Araknis Networks® products have a 2-Year Limited Warranty. This warranty includes parts and labor repairs
on all components found to be defective in material or workmanship under normal conditions of use. This
warranty shall not apply to products that have been abused, modified, or disassembled. Products to be
repaired under this warranty must be returned to a designated service center with prior notification and
an assigned return authorization (RA) number. Contact technical support for an RA number.
Contact Information
araknisnetworks.com
Technical Support [phone]
[e-mail]
The latest version of this QSG
may be found on the product
page support tab.
W
P
E