button is pressed.
B. Set the time of ending (23 hours 59 minutes maximum):
Press the button to set the time of ending;
The oven starts immediatel , and
G
AUTO
H
will flash. When the set time of ending is reached, the roast
process will shut automaticall . Then
G
AUTO
H
flashes, the alarm rings. The ringing will stop after the
button is pressed.
When the related button is pressed, the set roast process will be displa ed. Whenever the button is pressed,
and set backward the time to
G
0
H
, the set roast process will be cancelled. When button is pressed again,
the oven will revert to the manual operation process.
Timer
23 hours 59 minutes can be set as maximum.
To set the time, press the button, and then + or - button, until the required time is shown on the screen. After
the setting, the correct time (hour, minute) and the button will show on the screen. When the button is
pressed the time displaced will be seen. When the set time is reached, disappears and the alarm will ring
again. To stop the alarm, press the button.
Note: After pressing the related button, setting is supposed to be done in 5 seconds. In case of blackout, the set
process as well as the real time (hour, minute) will disappear. After the power is on again, three
G
0
H
and
G
AUTO
H
shows on the screen, the oven will automaticall reset.
3-keys timer procedure baking mode (onl available on certain models)
Adjust the clock after switch on:
Once it connected with electrical power, the displa will show “12:00” with the square s mbol above “ ”;
Press the “+” or “-” button will increase or decrease the number until it reaches the right time; after 5 seconds it
will start automaticall or ou can press the function button to make it starts.
Automatic setting (set the time of full automatic starting and ending)
1. Press the function button repeatedl until the square s mbol above the “ ” flashes, and press “+” or “-”
button to set the time frame baking for;
2. Press the function button repeatedl until the square s mbol above the “ ” flashes, and press “+” or “-”
button to set the time to switch off;
3. Adjusting the constant temperature button and choosing button to set temperature and baking method.
After these setting, the s mbols above the “ ” and “ ” will flash, it indicates the baking procedure of oven
has been set.
For example: if the food is required to bake for 45 minutes, and it is supposed to stop at 14:00.
Press the function button repeatedl until the square s mbol above “ ” flashes, and set the time of baking to
45 minutes;
Press the function button repeatedl until the square s mbol above “ ” flashed, and set the end time of baking
at 14:00.
After these setting, the proper clock (hour, minute) and the square s mbol will show on the displa , it indicates the
setting of baking procedure has been remembered automaticall .
When the clock shows 13:15 (between 14 -15min), the oven will switch on automaticall .
During the baking time frame, the square s mbol will keep flashing.
When the clock shows 14:00, baking will switch off automaticall . The alarm will ring, the square s mbol will flash,
to stop the ringing press an button.
Semi-automatic setting (set the time of automatic starting and ending)
A. setting the time frame of baking (10 hours longest)
Press the function button repeatedl until the square s mbol above “ ”, and set the time frame of baking;
Switch on the oven immediatel , the square s mbol above “ ” begins to flash. When the baking is done the
square s mbol above “ ” will flash, and alarm ring. To stop the ringing press an button.
B. setting the end time off baking (23hours and 59minutes longest)
Press the function button repeatedl until the square s mbol above “ ” flashes, and set the end time of
baking;
Switch on the oven immediatel , the square s mbol above “ ” begins to flash. When it reaches the time set,
baking procedure will switch off automaticall . The square s mbol above “ ” flashes,
the alarm will ring, the square s mbol will flash. To stop the ringing press an button.
The set baking procedure could be seen b pressing an function button repeatedl at an time, onl if the time
frame of baking is at “0” position. B adjusting the end time of baking to the current time, the set baking
procedure can be cancelled.
