Archatrak Street Deck User manual

Installation Manual
STREET
DECK
// 6’ x 12’
One-Car StreetDeck

Archatrak Inc.
TOOLS
Socket wrench (10mm)
Tile lifter
Hex key
Use tile lifter to remove porcelain pavers
from deck when dismantling StreetDeck.
Use hex key with hex socket screw to
secure ramp to ramp bracket.
Use socket wrench where carriage bolts and
hex screws are required.
Tools needed to assemble StreetDeck
Tape measure
4’ or 8’ level
Use tape measure for proper SE pedestal placement.
Use level when installing SE support
pedestals and when laying porcelain pavers.
Hand saw
Use hand saw to shorten length of watering
pipes in planter boxes.
1
2
3
4
5
6

Assembling
the StreetDeck
Perimeter
1
Archatrak Inc.
STREETDECK PERIMETER
Components
A
C
D
E
F
G
Perimeter beam 4’W
Crossbeam
Middle plate
Corner plate
Link bracket
x4
x2
x2
x1
x14
BPerimeter beam 3’W
x4
Hex head bolts & flange nuts
x8 per link bracket

Assembling
the StreetDeck
Perimeter
1
Archatrak Inc.
STREETDECK PERIMETER
Assembly
1Identify perimeter components. Arrange components in formation of StreetDeck (see below).
2Begin attaching perimeter components together using link brackets. Begin with the outer perimeter beams, followed by crossbeams.
B
C
D
E
F
B
B
B
AA
D
E
E
E
F
F
F
F
F
F
F
F
F
F
F
F
F
Top view of
connected plates
Underside view of
connected plates
B B
D
FF
Top view of
connected plates
Underside view of
connected plates
B
E F
GG
C
D
D
F
F
Top view of
connected plates
2.1 Connect corner plates , perimeter
beams and middle plates using
link bracket . Secure link brackets to
underside using 8 hex head bolts and
flange nuts per link bracket.
E
A
2.2 Secure link bracket to underside of
crossbeam and middle plates
using 8 hex head bolts and flange nuts
per link bracket.
DC
F
G
G
D
E
B
G

Decking
Assembly
2
Archatrak Inc.
DECKING
Components
‘SE’ support pedestals
Rubber pads
24” x 24” porcelain pavers
H
I
J
KPlanter bracket
x28
x20
x18
x8
NRamp
x1
MRamp bracket
x2 per ramp
OHex socket screw
For StreetDeck with ramp:
For StreetDeck with planters:
x2 per ramp
LMiddle bracket
x1
GHex head bolts & flange nuts
x2 per planter and middle bracket
GHex head bolts & flange nuts
x8 per link bracket

Decking
Assembly
2
Archatrak Inc.
DECKING
Assembly
3Use SE pedestals to elevate StreetDeck perimeter.
H
3.2 Elevate remainder of perimeter frame towards opposite
6’ side. Place pedestals every 24” and use level along
perimeter frame to check for necessary pedestal height
adjustments. Typically shorter pedestals are necessary
on the street edge, transitioning to incrementally taller
pedestals toward the sidewalk edge.
3.1 Begin on one of the 6’ sides. Snap o the 4 spacer tabs
on pedestal heads to allow underside of frame to sit
flush on pedestal head. Pedestal heights are adjusted
by holding the screw column firmly and rotating the
pedestal base left or right to raise/lower the pedestal.
StreetDeck perimeter height should be level with
sidewalk height so ramp will sit flush on pavers and
sidewalk.
1Decide ramp location and install ramp brackets with
protruding end as close to sidewalk as possible.
Shift assembled deck closer to sidewalk if necessary.
1.1 Use two ramp brackets per ramp. Choose ramp
location based on existing holes located on either end
of perimeter beam (see above). Use one hex head bolt
and flange nut to attach each ramp bracket to the
perimeter beam.
Repeat this step if you have more than one ramp.
Do not attach ramp to brackets until pavers are laid. Sidewalk Edge
M
G
M
2Square deck frame by measuring distance between
diagonal corners and shifting frame as necessary until both
measurements are equal.
Sidewalk Edge
6’
Sidewalk Edge
Street Edge

Decking
Assembly
2
Archatrak Inc.
DECKING
Assembly
5At all points where the SE pedestals are under deck frame components, place a
rubber pad directly above on surface of frame.
5.1 Rubber pads placed at planter bracket location are
cut in half, with half going on either side of planter
bracket.
5.2 Using a box cutter knife, remove all 4 spacer tabs
on the four pads located in the corners and pads
cut in half at planter brackets.
5.3 All other rubber support pads require
two tabs to be removed. Cut o tabs
parallel to deck frame perimeter.
I
4Attach planter brackets and middle bracket to StreetDeck perimeter frame.
If StreetDeck does not have planters, you may skip this step and go to step 5.
Sidewalk Edge
4.1 Using 2 hex head bolts and flange nuts per
planter bracket , attach planter brackets to
perimeter beams and corner plates in pairs per
planter location. Planter brackets in each of the
four corners should have curved bottoms facing
the bracket it’s paired with. The remaining four
planter brackets should have curved bottoms
facing away from the corners.
G
K
K L
K
K
K
K
K K K K
4.2 Using 2 hex head bolts and flange nuts , attach
middle bracket to crossbeam and middle plate.
G
L
L
Sidewalk Edge

Decking
Assembly
2
Archatrak Inc.
DECKING
Assembly
Lay remaining SE pedestals and porcelain pavers .
6.2 Lay porcelain pavers, one 3-paver row at a
time. Position pavers snug against spacer tabs
on pedestal heads taking care not to snap
o any tabs. Constantly check the deck for
level as you lay the pavers, adjusting pedestal
heights as necessary. Note that planter
brackets (where installed) will protrude from
the gaps between the pavers.
HJ
6.1 Lay remaining SE pedestals in 24” increments.
Sidewalk Edge
Sidewalk Edge
6
ON
Using the hex socket screws , secure the 4’ ramp
to both ramp brackets with hex key.
Repeat this step if using multiple ramps.
7
M
Sidewalk Edge

Planter
Assembly
3
Archatrak Inc.
PQ
PLANTERS
Components
Planter front and back panels
2’W x 3’H
Planter side panels
1’W x 3’H
TPlanter shelf
UPlanter feet
GHex head bolts and flange nuts
RS
Planter front and back panels
2’W x 2’H
Planter side panels
1’W x 2’H
x6x6
x4x4
x5
x20

Planter
Assembly
3
Archatrak Inc.
PLANTERS
Assembly
1Using 2 hex head bolts and flange nuts , securely
tighten the planter feet to front and back panels
ensuring the base portion of the L shaped foot is
facing inwards. Leave exactly 1” of the foot protruding
from the base of the panel.
There should be one foot on either side of the front
and back panels.
2Connect side panels to front and back panels
1”
Q P
PQ
rivet nuts
G
U
S R
G
P R
2.1 Using 20 hex head bolts and flange nuts connect
side panels to front and back panels . Repeat
for remaining two 3’H planter.
PQ
Using 16 hex head bolts and flange nuts , connect
side panels to front and back panels . Repeat
for second 2’H planter.
S R
2.1
G
G
Be sure the 2 rivet
nuts towards bottom
of both side panels
are closest to the
same large panel.
3Stand planter upright. Decide planter shelf height;
insert 4 hex head bolts and flange nuts on
innermost side of slot. Rest planter shelf on 4 bolts.
G
T
T
Hex head bolt and nut on
innermost side of slot.
P
U
G

Planter
Assembly
3
Archatrak Inc.
PLANTERS
Assembly
4Secure planter boxes to planter brackets.
3’H
3’H 3’H
2’H
2’H
Placement of planters:
For planters in four corners, use socket wrench
to secure 2 hex head bolts through each
planter bracket into existing rivet nuts located
towards the bottom of the planter side panels.
G
4.1
4.2 Secure middle planter to middle bracket by
inserting two hex head bolts down through
front and back panel into top of middle bracket.
Tighten with flange nuts.

Planter Soil
Sack Assembly
4
Archatrak Inc.
V
W
PLANTER SOIL SACK
Soil sack
Drain hose
XInsulation panels
Components
YWatering pipe
ZFilter fabric
x8
x8
x32
x8
x8

Planter Soil
Sack Assembly
4
Archatrak Inc.
Assembly
1Insert soil sack with drain hose in planter. Insert drain hose into hole located in the center of the planter shelf. Insert the
insulation panels against inside edge of all four panels. Carefully check that the edges of the soil sack stand upright.
2Place watering pipe in the corner of planter. Use hand saw to shorten length of watering pipe if necessary.
Cover the drain hole with piece of filter fabric.
V W
X
Y
V
W
X
Y
Z
3Fill sack with soil and plant vegetation.
PLANTER SOIL SACK

Fence Assembly
5
Archatrak Inc.
AA
FENCE
3’W x 3’H fence panel
3’W x 2’H fence panel
GHex head bolt
Components
AB
x2
x2
x6 per fence panel

Archatrak Inc.
FENCE
Assembly
1Attach fence panels to planters by screwing 6 hex
head bolts into existing rivet nut holes.
3’H fence panels attachalong the 12’ long street
edge, while the 2’H fence panels attach along the 6’
ends of StreetDeck.
AA
AA
AB
AA
5
Fence assembly
G
AA
AB
AB
AB

5
Archatrak Inc.
866.206.8316
[email protected]
www.archatrak.com
Archatrak Inc.
2 Wisconsin Circle, Suite 700
Chevy Chase, MD 20815