iDTRONIC ID GATE 8900 User manual

Speed Gate
ID GATE 8900
User Manual

IDGATE8900
2
Contents
1. Product Introduction ....................................................................................................3
1.1 Note ......................................................................................................................... 3
1.2 Functional features................................................................................................... 3
1.3 Structures and dimensions ....................................................................................... 4
1.4 Technical parameter ..................................................................................................4
2. Product Structure and Working Principle ....................................................................5
2.1 Electronic control system of channelgate................................................................................ 5
2.2 Operating principle of the system.....................................................................................6
3. Install Instruction........................................................................................................... 7
3.1 Installation note &suggestion .................................................................................. 7
3.2 Turnstile cable drawing.............................................................................................. 8
3.3 Turnstile circuit board wiringdiagram..................................................................................9
4. Equipment Function Debugging....................................................................................10
4.1 Gate Position Adjustment ............................................................................................ 10
4.2 Parameter Setting ...................................................................................................... 11
5. Product Maintenance.......................................................................................................12
5.1 Daily maintenance....................................................................................................... 12
5.2 Tips and troubleshooting ..............................................................................................13
6. Customer Services ...........................................................................................................13

IDGATE8900
3
1. Product Instruction
1.1 Note
1) Before installation, operation or maintenance, turn off power.
2) Do not change the inside wiring, take a photo before any disconnection.
3) Do not use the turnstile inside power supply to connect other third-party device.
4) Do not operate when thundering and lightning, in case damage the turnstile electrical parts.
1.2 Functional features
◆Speed gate outstanding features: 0.2s fast openand close speed, exceeding slim housing, different height glass arms.
◆The glass arm can be heightened to 1800mm forhighsecuritycontrol to prevent unauthorized person from climbing.
◆Speed gate with unique design, stylish of modernand urbanization cabinet, black swipe card panel, attractive red and green LED strip,
solid body crate, high-end polish process.
◆Turnstile gate with standard open/close relaysignal,it can be integrated with any type of the third-party access control parts. (e.g.:
RFID, Fingerprint and Biometric reader device).
◆Unifiedexternalelectricalinterface,whichcanbe linked to a variety of card readers, and can be remotely controlled and
managed by the management computer;
◆In case of emergency,turnstile gate will openautomaticallyto allow free passage when power off.
◆Automatic reset function. If the user fails topasswithin the setting time, the system will cancel the authority.
◆The whole system runs smoothly, long-life performance,highoperation dependability and fast response.
◆Working way: Single directional or Bi -directional.
◆LED green and red indicator.
◆Alarm function, in case of illegal intrusion andreverseintrusion.
◆Infrared sensor to prevent pinch pedestrians.
◆Anti-breakthroughfunction.Thegateislockedautomaticallyuntil opening signal received.
◆Anti-trailing function, the turnstile will alarmif someone wants to burst in without permission.
◆Turnstile gate will open automatically when poweroff,which is complying with fire safety requirements. Easy to install and maintain.
1.3 Structures and dimensions
Optical speed gate he passing width can reachto600mm for normal passage, and can support 1200mm arm for wide
passageway, wheelchair, and pedestrian with large luggage can also pass.
*High Glass Arm: the arm can be heightened to 1800m(maximum)for high security protection.

IDGATE8900
4
Short Glass Arm
High Glass Arm
1.4 Technical parameter Figure 1
Item
Description
Cabinet
304 Stainless steel+Plexiglasglassarm
Dimension
1683 *132* 1000mm
Weight
75kg/pcs (single core),85kg/pcs(doublecore)
Arm Height
900-1800mm(Optional)
Pass Width
600mm(standard),1200mm(handicapped)
Power supply
AC220V/110V,50/60Hz
Working voltage
24V DC
Emergency
Automatic arm open whenpoweroff
Power consumption
40W
Working environment
Indoors or outdoors
Working temperature
-20 °C - 75 °C
Humidity
0 ~ 95% (no freeze)
Control interface
Dry contact/Relay signal
Opening time
0.2 seconds
Passing speed
55 persons/min

IDGATE8900
5
2.1. Electronic control system of channel gate
The electronic control system consists of cardreader,main control board, infrared sensor, direction indicator board, alarm,
transformer, etc.
Card reader (self-provided): after reading the information on thecardand judging and processing, send the application pass signal
(switch signal) to the main control board.
Master control board: the control center of the system, whichreceivessignals from the card reader and infrared sensor, makes logical
judgment and processing of these signals, and then issues execution commands to the direction indicator, motor, counter and
alarm.
Infrared sensor: detect the pedestrian position and play theroleof safety protection.
Direction indicator light: displays the current status of the channeland guides pedestrians to pass through the channel in a safe and
orderly manner.
Alarm: when the system detects pedestrians enteringthepassageillegally, it will send out an alarm
2. Product Structure and Working Principle

IDGATE8900
6
Item NO.
NAME
FUNCTION
1
Entrance guard system
IC/ID card accesscontrol,fingerprint machine, face
recognition,two-dimensional code device,
gate opening signal onthecontrol board of gate machine,
remote control, button to open the gate(optional)
2
Control board
The control center ofthesystem, which receives signals from
the card reader and infrared sensor,
and makes logical judgmentand processing of these signals,
and then sends out execution commands to the
direction indicator, motor, counter and alarm.
3
Infrared sensor
Detectthepositionofpedestrians and safety protection
4
Direction indicator
Display the currenttrafficsign status of the gate and guide
pedestrians through the gate
5
Alarm (speaker)
When the system detects a pedestrianillegallyentering the passageway, it gives an alarm.
6
Motor
Drive the mechanism
7
PowerSupplySwitch
Control panel power supply
2.2. Operating principle of the system
a) Turn on the power and the system will enter into working state after 3 seconds.
b) Whenthe card reader reads the valid card, thepeak-mincer will make a pleasant sound, indicating to pedestrians that the card
has been read successfully. At the same time, it will judge and process the information read from the card, and send an
application for approval signal to the main control board.
c) The main control board receives the signalsfromthecard reader and infrared sensor, and after comprehensive processing, sends
effective control signals to the direction indicator and motor, so that the direction indicator sign turns into the green arrow
pass sign. At the same time, the turnstile sends the setting voice, the main control board controls the motor operation,
and the gate is opened to allow pedestrians to pass.
d) After the pedestrian passes through thechannelaccording to the direction indicator, the infrared sensor senses the whole process
of the pedestrian passing through the channel and continuously sends signals to the main control panel until the pedestrian
has passed through the channel completely.

IDGATE8900
7
e) If a pedestrian forgets to read his card or reads an invalid card and enters the channel, the system will forbid the
pedestrian to pass through and issue a voicealarm.The alarm will not be lifted until the pedestrian exits the channel. Rereading a
valid card allows passage.
3.1 Installation note & suggestion
Note: Duringinstallationandconstruction,relevantcircuitsshould be disconnected to ensure that all circuits are correct before
energizing.
►►Installation Suggestion:
1) For cables, suggest laid 60mm deep, over 50mm, and connector area be bending to avoid water.
2) If the turnstiles install in the outside, suggest installed in concrete deep 100-200mm to avoid natural damaged.
3) All the operation should be done when power off.
4) Wear the strong electric cable and the weakelectriccable are respectively with 3/4 "PVC pipe and buried to the
corresponding position with cement.
5) After adjusting the foundation surface, arrange the equipment in good order.
6) After the hole location is determined, drill the hole and embed the anchor bolt or expansion bolt of M12.
7) Open the case, select one of the equipment asthereference (preferably choose the middle one as the reference), align the
base bolt hole with the corresponding anchor bolt, and pre-tighten the nut.
8) Connect the power line and control line according to the wiring diagram, and connect the system protection ground wire.
9) Check the mains wiring according to the wiringdiagram,check the power wiring and other wiring of the whole equipment are correct,
and the power can be adjusted after confirmation.
10) After completion of the installation, checktheconnection condition of earth wire, connector assembly for connecting line and all
moving parts with the device. Make sure the connection is firm in order to prevent failure caused by long time operation.
If any screw or part is not tightened, please tighten.
3. Install Instruction

IDGATE8900
8
11) After the equipment status check is normal,thefollowing functions can be debugged.
.
Figure 2
3.2 Turnstile cable drawing
Figure 3

IDGATE8900
9
3.3 Turnstile circuit board wiring diagram
*Turnstile electrical parts area with power supplyport,please connect to 110V/220V electrical power supply.
*Turnstile circuit board with port “NO1”, COM”,“NO2”,it can be connected to any type of the third-party access controller device.
Figure 4

IDGATE8900
10
4.1 Gate Position Adjustment
1. Press “Set” (middle button) for 5 times continuously,thesystem will prompt "please adjust gate manually".
2. Push the gate to the target position and stopit for 3 seconds. The speaker prompt "beep" or the LED light flashes once, the
system will take the current position as the target position.
* The system will automatically determine whetherthetarget position is left, right or middle target position.
3. Finally, push the gate to the middle targetpositionand holding for about 10 seconds. The system will prompt “adjustment completed
“, then the whole program is finished.
*In most cases, the system will automaticallyobtainthe appropriate left position and right position, and the user only needs to adjust
the middle position.
4.2 Parameter Setting
1. Long press the “Set” button, till the nixie tubeflashes.
2. The "Menu" button for choosing the menu, the "Value" buttonforsetting the parameter.
3. Long press the "Set" button 2S, the digital tubestopsflashing,then menu values are saved successfully.
Figure 5
Menu
Function
Range
Default
Parameter function description
0
Machine number
1~99
1
For 485 communication
1
Unlock mode
1~4
1
1: standard 2: IR1 trigger
3: IR4 trigger 4: IR1 trigger and IR4 trigger
2
Keeping unlocktime
1~20
6
Time unit: Second
3
Voice forOpen-L
0~9
0
0, thank you; 1, come in; 2, good bye;
3, welcome; 4,see you; 5,havea nice day; 6, have nice trip;
7, please put on your safety helmet; 8, Verify success; 9
null(mute);
4
Voice forOpen-R
0~9
3
5
Volume
1~9
5
The higher the value, thehigherthe volume
6
Main motorspeed
1~25
13
The higher the value, thehigherthe speed
7
Slave motorspeed
1~25
13
8
Restore factory
0~2
0
1: Automatic aging test
2: Restore factory
4. Equipment Function Debugging

IDGATE8900
11
9
Show downrange
1~30
10
To control the effect of gatepanel swing, the higher the value, the
earlier the braking
10
Self-checkrunning
speed
1~9
3
The higher the value, thefasterspeed
11
Passing Mode
0~2
0
0: Free passingmode: delayed 1.5Swhen detection the
battery car.
1: memory function, N personcardby N person passing.
2: one card and one personpassing.(No battery car detection function)
12
Locking control
0~9
1
0: when triggers the last groupof the IR, the gate will close.
1: After passing the lastgroupof the IR, the gate will close.
2~9:Afterpassingthelastgroup of IR, the gate will close with a delay
(n-1 second)
13
Number ofmotors
0~1
0
0: Dual motor
1: Solo motor
14
Language
0~1
0
0: Chinese; 1: English
15
Stacking control
0~1
1
0: No rebound in case ofresistance
1: Rebound in resistance
16
Stacking sensitivity
1~9
5
The higher the value, the higherthe sensitivity
17
Retrograde control
0~1
1
0: Retrograde trigger doesnot close the gate, only voice alarm
1:Thegatewillbeclosed by retrograde.
18
Type of gate
0~3
0
0: swing gate (quick passgate)
1: Cylindrical swinggate(supermarket swing gate) 2: Flap gate
3: Swing gate with unidirectionalopeningmode
19
Direction of arm when
power off
0~2
2
0: Turn off the switch in theleft pass direction after power failure.
1: Turn the switch to therightafter power failure.
2: The system automaticallyselectsthe power off direction according to the
current situation.
* The opening directioncanreferto the direction indicated by the arrow of
the ceiling light board
20
Forceofpushingthe gate
1~9
5
The greater the value, thegreaterthe force. Excessive force may
cause power restart. It isrecommendedto use the default value for
6.25A power supply
21
Voice of beak incontrol
0~1
1
0: there is no voice promptwhenthe illegal intrusion event occurs.
1: There are relevant voicepromptswhen an illegal intrusion event occurs.
22
IR Signalre-trigger
delay
1~9
5
time=value*20ms(default100ms)
23
Direction of motor
operation
1~4
1
1: the main machine is turningforward,the slave machine is
reversing;
2: the main machine reverses,and the slave machine forwards; 3: the main
machine is forward, the slave machine is forward;

IDGATE8900
12
4: the main machine reverses,theslave reverses;
24
Clutch control
0~1
0
0: normal lock, 1: normal unlock
25
Hall modeofmotor
0~2
0
0: auto, 1: mode A, 2: modeB
26
Input signalfiltering
1~9
3
time=value*10ms(default30ms)
27
Opening stroke
infrared anti-clamp
0~1
0
0:The infrared anti - clamp is not effective during gate
opening
1:The infrared anti - clamp is effective during gate opening
28
Anti-trailing alarm
0~2
0
0：Closing；
1：Trailing voice alarm, do not turn off the gate；
2：Trailing voice alarm, and turn off the gate;
29
Zero deviation alarm
threshold
0~9
2
The higher the value，the larger deviation of the door panel
allows
30
Anti - clip infrared
free pass switch
0~1
1
0：Free passage mode: the anti-clip infrared does not trigger
the opening;
1：Free passage mode: the anti - clip infrared trigger switch,
easy to pass quickly
31
Free passage
memory function
switch
0~1
1
0：Free passage mode: no memory function, multiple trigger
infrared can only pass 1 person;
0：Free passage mode: open memory function, N person
trigger infrared can by N person passing.
32
Main motor sliding
compensation
0~9
0
The sliding compensation can be appropriately increased
when the switch gate plate cannot return to zero at the first
time after the completion of the self-test. Excessive
compensation may cause the door to shake when it stops.
Make sure to adjust this parameter when the door is moving
smoothly.
33
Slave motor sliding
compensation
0~9
0
5.1 Daily maintenance
➢To avoid the risk of electric shock, always ensurethepower off before inspecting.
➢Suggest inspected at regular time, to ensure allpartsin good working.
➢The material made by stainless steel, do not usehardmaterial to clean it.
➢Fingerprintsor stubbornstainscleaningway:scrubby soap water or alcohol, sponge rinse with clean water, wipe dry as
necessary.
5. Product Maintenance

IDGATE8900
13
5.2 Tips and troubleshooting
1. After swiping card, if the arm doesn’t open,pleaserecheckwhether all the wire well connected.
2. If indicator doesn’t light, or indicate wrongdirection,please exchange the inside wires to test.
3. Turnstile will automatically open after power off;if it did not, it caused by the storage battery power not enough. Make sure the
storage batter with enough power.
4. The arm did not work together, check if the syncwiresconnect well.
5 .The arms open but fail to close, check infraredsensorif it matched well.
Digital tube cue
Fault
Reasons and solutions
E010
The main motorcannotbe detected
The hall cable or motorcableis incorrectly connected, and the
motor hall is faulty
E020
Theslavemotor cannotbe detected
E030
The main and slavemotorcannot be
detected
E050
Theself-checkprocessisabnormal
Hall phase or motor phasesequencemisconnection,
motorfailure,movement slipor stuck
We are very happy to help you in the future whenyouencounter problems or product defects, if the use or operation is not clear, please
timely contact the after-sales service staff.
Warranty Card
(Warranty: 3 years)
Order Date:
Product Name:
Product Model:
Customer Country:
Company Name:
Email:
Fault descriptions with photo/video:
6. Customer Service