ARCHEAN Audio Accessibilite DCSTS-K072 Operation manual

Window Intercom System
Speaker Pod and Screen Mounted
Microphone –DCSTS-K072
Installation &
User Guide
December 2020

2
Contents
Product Overview
Components
Connections
Installation Instructions
Speaker & Microphone Kit Installation
  StaSideInstallation
Customer/Visitor Installation
Hearing Loop Installation
 AmplierSetup
Troubleshooting
Engineer’s Mode
3
3
4
5
6
6
7
9
10
12
13
Contactahasapolicyofcontinuousproductdevelopment,andthereforesmallspecication
changesmaynotbereectedinthismanual.Images,labels,packaging,accessoriesandproduct
coloursaresubjecttochangewithoutnotice.

3
Speaker & Microphone Components
Product Overview
Window intercom systems provide assistance for clear communication where
normal speech is impaired by use of glass, a security screen or other similar
barriers.
There is an optional hearing loop facility, providing additional assistance for
hearingdevicewearers.
1. Installation and User Manual
2. Amplier
3. IEC Lead
4. Power Supply
5. HearingLoopAerial
(optional)
Fixing Kit:
• Adhesive Clip x 10
• No.6x1/2”CountersunkScrewsx15
• P-Clips x 6
5
General Components
1. Speaker Pod
2. StaPod
3. Screen Mounted Microphone
with Bent Stem
4
3
2
1
1
3
24

4
Connections
LED connection or alert tone (if required)
CondenceLEDtoconrmthesystemispowered
oranalerttonefortheattentionofsta
Stamicrophone
Customer/visitor microphone
CondenceLED(ifrequired)forstatusalerts
and fault detection
Hearing loop aerial
Line in connection for
external audio source
Staspeaker
Customer/visitor speaker
Power input
connection
Use power supply
through ground
supply only

5
Werecommendthatinstallationiscarriedoutbyaqualiedengineer,
adheringtorelevantstandards.
Checkthecontentsoftheboxtofamiliariseyourselfwiththecomponents.
Installation Instructions
A basic toolkit recommended to install the system will include:
Trim cables if necessary (excluding the power supply)
to the required length to connect to the back of the
amplier.Bareapproximately6mmofthecableendsto
connecttothe2pinplugs.
• Wire Cutters/Strippers
• Tape Measure
• Pencil or Marker Pen
• Cable Ties
• Trunking
• Screwdrivers(FlatorBlade2.5mm
and Phillips Head PH2)
• Battery or Mains Drill
• Drillbits: 2mm, 3mm, 5mm and 7mm
• Cable Tacking Gun (10mm)
Recommended Tools
Staff Counter Side
Customer / Visitor
Counter Side
StaPod
Screen Mounted
Microphone
Speaker Pod
Negative -
or screened cable
Positive +

6
1. Placetheamplierunderthestacounter,ensuringthatitwillnot
obstructstawhentheyaresitting.
2. Markthefourxingpointsfortheamplierunderthecounter.
4. Drillandxtheamplierinplaceusingthesuppliedscrews.
6. Installtheamplier’spowersupplyclosetoapowersocketoutletusing
thesuppliedmountingbracketandxingscrews.
Fixing points
AmplierInstallation

7
Microphone & Speaker Installation
1. Position the screen mounted microphone stem’s on the customer side of
thecountertop.
2. Markthe2xingpointsand1cableroutereadyfordrilling(seethe
diagrambelow).
3. Drillpilotholesforthexingsandacableholeifneccesary.
4. Feedwiringthroughthecableholebacktotheamplierandxthe
microphoneinplaceusingthesuppliedscrews.
5. Fix the microphone head to the screen using the double-sided pad
supplied.
6. Placethestapodonthestasideofthecountertop,ensuringit
doesnotcauseanobstructionandisasclosetostaaspossible.The
recommended minimum distance between this pod and the screen
mountedmicrophoneis300mm.
Staff Counter Side
Customer / Visitor
Counter Side
StaPod
Screen Mounted
Microphone
Speaker Pod

8
7. Place the speaker pod on the customer side of the counter top, ensuring it
doesnotcauseanobstruction.
8. Speakerpodsandstapodscanbeeitherfreestandingorxed.Moveto
step14ifyoudonotwishtoxthepodstothecounter.
9. Usecablemanagementholesinthecountertorunthestapodand
speakerpodcablestotheamplier.Iftherearenotalreadycable
managementholes,drillsuitablelocationsneartherearofboththesta
andcustomersidesofthecounter.
10. Removethetopofthepodstogainaccesstothexingpoints.
11. Markthetwoxingpointsonthebottomofbothpods.Thenmarktwo
cable holes to be drilled, one for both the customer/visitor side and the
staside.
12. Ensuretherewillbeaccesstoretrievethecablesthendrilltheholes.
13. Fixthepodstotheirrespectivecounters.
14. Feedthepods’wiresthroughthecablemanagementholes.
15. Routeallcablingneatlytotheamplierlocationonthestaside.

9
Theaerialshouldbexedunderthedesk-toporcountercentrallyonthe
customer or visitor side, one half mounted horizontally under the counter and
theotherhalfmountedvertically,facingthecustomer/visitor(asintherst
scenariobelow).
Position the aerial under the counter using either the provided P-clips
oranotherxingmethodofyourchoice.Seethediagrambelowfor
recommendedpositioning.
Aistheoptimumlayoutforacounterhearingloop.
B and C are acceptable only if A is not possible and the layout is aligned so
thatthemagneticeldwillbedirectedtowardsuser’sheadheights.
Ensureallhearingloopsignageisdisplayedclearly.
X
X
Hearing Loop Installation
(Optional)
A B C

10
AmplierSetup
1. Connectallgreenplugstothebackoftheamplier,followingthe
locationsprintedabovethesockets(seepage4).
2. PowerontheamplierbypressingtheOn/Obutton.
3. Whenpoweredandinnormaloperationalmodetheamplierwilldisplay
VolumeInLED1andVolumeOutLED1assteadygreen.
4. Whentheamplierisswitchedo,allaudioismutedandnoneofthe
LEDsareilluminated.Pressinganybuttonwillturntheamplieronagain.
5. AdjustVolumeInandVolumeOuttoacomfortablelevel.
6. Press and hold the Volume In (+) or (-) buttons to increase or decrease the
level.ThecorrespondingLEDbarwillshowthevolumesetting.
6. Ensure the mouse microphones are placed as close to their intended
usersaspossible.
7. Checktheamplierisfullyfunctionalbyensuringthered‘fault’lightis
NOTshowingonthefront.
8. The Amplifier is now set up.
OurWindowIntercomSystemampliersarepre-settovolumelevels
suitablefornearlyallusers.ShouldyouneedtoadjusttheMaximum
Volume,DuckingorHearingLooplevelsoutsideofthepre-setamplier
parameters,useEngineer’sMode(seepage13).
Overview of Front Panel Buttons
Volume In (Customer/Visitor to Staff)
Increase and decrease
Volume Out (Staff to Customer/Visitor)
Increase and decrease
Settings
On/O
Setup