Arcisan VE018700 Operation manual

15
18
19
17
14
22
8
13
20
6
1
5
21
3
22
HOB MOUNTED TAP SET
• VE018700
• VE018100
• VE018140
• TR018700
• TR018100
• TR018140
• RR018700
• RR018100
• RR018140
INSTALLATION AND CARE INSTRUCTIONS
Important Information
• Hot and cold water inlet pressures should be equal.
• Operating static pressure is 150—500kpa. If pressure exceeds this, then an
approved pressure limiting valve must be fitted.
• Pipeworkmust beflushed out prior to installation of the mixer. Damage caused to
themixer by debris coming through the pipework is not covered under warranty.
• Installation should comply to AS/NZS3500.1 2003 or the relevantlocal
requirements.
• Maximum hot water temperature is 75°C.
• Not suitable for gravity feed applications.
Maintenance and care
• Using a soft cloth with a mild detergent or soap is all that is required to clean
surfaces.
• Do not use abrasive cream cleaners or citrus based cleaning products. These will
damage the surface.
• Aerator may be removed and cleaned should it become blocked.
WARRANTY
Guarantee
Arcisan mixers are covered by a 15 year conditional residential warranty subject to the terms
below.
> 15 year cartridge replacement warranty against the ceramic disc cartridge leaking—parts
only.
> 7 year product or parts warranty against manufacturing defects. (Hoses and hand sprays
on kitchen mixers are 2 years).
> 1 year replacement product or parts and labour warranty.
Streamline reserves the right to assess, fix, replace or service warranty claims as they see fit.
The warranty period applies from date of purchase or date of handover for new buildings. If
this is not available, the manufacturing date stamp on the product will be used.
Warranty claims should first be directed through the point of purchase. It is mandatory that
the purchaser provide proof of purchase and the warranty is valid for the original purchaser
only and is not transferable.
Exclusions
The warranty does not apply to the following cases:
• Blocked or damaged aerators are not covered under the warranty. Other damage caused
by not flushing the system before connection or use.
• Damage caused by improper installation, abuse, accident and misuse. Also previous repair
or alteration without the company’s or agent’s permission.
• Warranty only applies to items purchased through an authorised re-seller within Australia.
• Tapware used in a commercial setting. This is subject to a 1 year parts and labour warranty.
• General wear and tear from normal use of the product, including scratching from cleaning.
• Water temperature or pressure exceeds the stated maximums. The maximum water
pressure is 500kpa and maximum temperature is 75 degrees Celsius.
Consequential Damages
Streamline Products will not liable for damage to other items (floor coverings, walls, lights
and other fittings) or any other type of consequential losses caused by a defect in the
product, except when the failure amounts to a major failure under your statutory rights.
Statutory Rights
Our goods come with guarantees that cannot be excluded in the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
Contact
This warranty is provided by Streamline Products P/L
Phone: [phone]
Email: [e-mail]

INSTALLATION
15
18
19
17
14
22
8
13
20
6
1
5
21
3
22
1. Install spout (3) with O-Ring (21) onto benchtop. Fit locknut (5) with washer (22) and
tighten.
2. Install breech (1) onto side bodies (6) and tighten compression nuts softly (13).
3. Fit Side body (6) and breech assembly (1) onto bench top. Screw on top fixing nut (14)
with seal (22) onto side body (6) until the fixing nut (14) is almost level with the top of
hexagon nut on cartridge. Retighten compression nuts (13).
4. Ensure that the both cartridges are in the ‘OFF’ position
COLD HANDLE – Turn anti-clockwise
HOT HANDLE – Turn clockwise
5. Install handle insert (17) with screw (19). Recess in handle insert (17) must face
outwards as follows,
LEFT FACING RECESS – Hot side
RIGHT FACING RECESS – Cold Side
6. Place handles (15) on handle inserts (17). Unscrew fixing nut anti-clockwise (14) until it
just touches handle, then screw it clockwise a half turn to allow for enough clearance to
avoid any rubbing.
7. Fit handles (15) the inserts (17). Align onto the recess and tighten grub screws with the
alan key provided.
8. Tighten locknut (8) and ensure that the handles do not rub when used.