Arcisan Synergii SY01240 Operation manual

Synergii bath-shower mixer
with diverter
Installation and Care Instructions
IMPORTANT INFORMATION
• Hot and cold water inlet pressures should be equal.
• Operating static pressure is 150—500kpa. If pressure exceeds this,
then an approved pressure limiting valve must be fixed.
• Pipework must be flushed out prior to installation of the mixer.
Damage caused to the mixer by debris coming through the pipework
is not covered under warranty.
• Installation should comply to AS/NZS3500.1 2003 or the relevant
local requirements.
• Maximum hot water temperature is 75°.
• Not suitable for gravity feed applications.
MAINTENANCE AND CARE
• Using a soft cloth with a mild detergent or soap is all that is required
to clean surfaces.
• Do not use abrasive cream cleaners or citrus based cleaning
products. These will damage the surface.
• Aerator may be removed and cleaned should it become blocked.
Warranty
Guarantee
Arcisan mixers are covered by a 15 year conditional residential warranty subject to the terms
below.
• 15 year cartridge replacement warranty against the ceramic disc cartridge leaking—parts
only.
• 7 year product or parts warranty against manufacturing defects. (Hoses and hand sprays
on kitchen mixers are 2 years).
• 1 year replacement product or parts and labour warranty.
Streamline reserves the right to assess, fix, replace or service warranty claims as they see fit.
The warranty period applies from date of purchase or date of handover for new buildings. If
this is not available, the manufacturing date stamp on the product will be used.
Warranty claims should first be directed through the point of purchase. It is mandatory that
the purchaser provide proof of purchase and the warranty is valid for the original purchaser
only and is not transferable.
Exclusions
The warranty does not apply to the following cases:
• Blocked or damaged aerators are not covered under the warranty. Other damage caused by
not flushing the system before connection or use.
• Damage caused by improper installation, abuse, accident and misuse. Also previous repair
or alteration without the company’s or agent’s permission.
• Warranty only applies to items purchased through an authorised re-seller within Australia.
• Tapware used in a commercial setting. This is subject to a 1 year parts and labour warranty.
• General wear and tear from normal use of the product, including scratching from cleaning.
• Water temperature or pressure exceeds the stated maximums. The maximum water
pressure is 500kpa and maximum temperature is 75 degrees Celsius.
Consequential Damages
Streamline Products will not liable for damage to other items (floor coverings, walls, lights
and other fittings) or any other type of consequential losses caused by a defect in the
product, except when the failure amounts to a major failure under your statutory rights.
Statutory Rights
Our goods come with guarantees that cannot be excluded in the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Contact
This warranty is provided by Streamline Products P/L
Phone: [phone]
Email: [e-mail]

Installation
1. Flush pipework prior to installing to ensure it is free of debris.
2. Screw the shower mixer body (1) to the nogging. Ensure depth to
finished wall is within the specified limits of 74 to 111mm. Do not
remove plastic protective cover at this stage.
3. Attach water hot and cold inlets and outlet and test for leaks.
4. After wall has been finished, remove plastic protection cover. Apply
sealant to inside perimeter of dress plate (2) and push on firmly
against the wall.
5. Push on mixer handle (3) and lock into place using grub screw (4).
SYNERGII BATH-SHOWER MIXER WITH DIVERTER
74-111
55
Finished wall
50mm
recommended
30mm
recommended
2
1
3
6
4
Switched
output
Default
output