Ardisam Eskimo Z43 User manual

Power Ice Auger
Operator's Manual
IB-Z43/Z51
Rev. 09/9/04
© Copyright 2004 Ardisam Inc.
All Rights Reserved. Printed in USA.
Models
Z51, Z51T8, Z51Q8
Z51Q9, Z51Q10
Models
Z43, Z43T8, Z43Q8
Z43Q9, Z43Q10

Page 2
INTRODUCTION, REGISTRATION AND WARRANTY
THANK YOU ÷ ÷ ÷
for purchasing an Eskimo®Power Ice Auger from Ardisam,
Inc. We have worked to ensure that it meets high standards
for usability anddurability. With proper care, yourauger will
provide many years of service. Please take the time to read
thismanual carefullyto learnhow tocorrectly operateand
maintainyour auger.Congratulationson yourinvestment in
quality.
WARRANTY
One Year Limited Warranty
The Ardisam, Inc., Manufacturing Company warrants this Eskimo® Ice Auger to be free from defects in material or
workmanship. Conditions of this warranty include:
What is covered under warranty:
Ardisam, Inc. will repair or replace any part defecti e in workmanship or material within one year after deli ery of the
ice auger to the original purchaser.
What is not covered under warranty:
This warranty applies only to products which ha e not been repaired or altered outside our factory. It co ers only
defects resulting from normal use, and does not co er defects arising from misuse, alteration, negligence,
commercial use, or accident. This warranty applies only to the original purchaser, and is not transferrable.
How to obtain service:
Return the product to us at the address below with transportation charges prepaid.
This warranty supersedes all other warranties either expressed or implied and all other obligations or liabilities on our
part. Ardisam, Inc., does not assume, and does not authorize any other person to assume for us, any liability in
connection with the sale of our products. This guarantee is void unless warranty card is properly filled out and
returned to Ardisam, Inc., Cumberland, Wisconsin, at time of purchase.
REGISTRATION
Fill out and mail the registration card located in your parts
packet. Warranty is valid only if your completed registration
card is received by Ardisam, Inc., at time of purchase.
Model Number _________________________________
Serial Number _________________________________
Engine Serial Number ___________________________
Date of Purchase _______________________________
Place of Purchase ______________________________
ARDISAM
Ardisam, Inc.
1690 Elm treet, Cumberland, WI 54829
Phone [phone] Fax [phone]
1-800-345-6007
Email [email protected]
www.ardisam.com

Page 3
SAFETY
Owner's Responsibility
Accurate assembly and safe and effective use of the auger
is the owner's responsibility.
•Read and follow all safety instructions.
•Carefully follow all assembly instructions.
•Maintain the auger according to directions and schedule
included in this Eskimo operator’s manual.
•Ensure that anyone who uses the auger is familiar with
all controls and safety precautions.
Special Messages
Your manual contains special messages to bring attention
to potential safety concerns, machine damage as well as
helpful operating and servicing information. Please read all
the information carefully to avoid injury and machine
damage.
NOTE: General information is given throughout the
manual that may help the operator in the operation or
service of the machine.
Avoid damage! This text is used to tell the operator of
actions or conditions that might result in damage to
the machine.
Avoid injury! This symbol and text highlight potential
hazards or death to the operator or bystanders that
may occur if the hazards or procedures are ignored.
Important Safety Preca tions
Please read this section carefully. Operate the auger
according to the safety instructions and recommendations
outlined here and inserted throughout the text. Anyone who
uses this auger must read the instructions and be familiar
with the controls.
This symbol points out important safety instructions
which if not followed could endanger your personal safety.
Read and follow all instructions in this manual before
attempting to operate this equipment.
•The ice blades are very sharp. Use extreme caution
when drilling a hole or replacing the blades. Put blade guard
on after each use.
•Do not carry the auger powerhead between holes with
the engine running.
•The auger should not rotate when the engine is idling. If
it does rotate when engine is idling, contact Ardisam, Inc.
for instructions.
•Always keep hands, feet, hair and loose clothing away
from any moving parts on engine and auger.
•Do not allow children to operate this power auger. Do not
allow adults to operate the auger without proper instruction.
•Do not operate any power equipment under the influence
of alcohol or drugs.
•Keep all screws, nuts and bolts tight.
•Engine should be turned off and cool, spark plug wire
must be removed from spark plug before any repairs are
attempted.
•Temperature of muffler and nearby areas may exceed
150° F (65° C). Avoid these areas.
•Never run engine indoors or in an enclosed area. Engine
exhaust contains carbon monoxide, an odorless and deadly
gas.
•If the ice auger becomes unturnable in a hole, turn
engine off and allow to cool before attempting to remove it
manually.
CAUTION
CALIFORNIA PROPOSITION 65 WARNING
Engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
WARNING

Page 4
SAFETY
Engine Safety Preca tions
Warning Carbon Monoxide Poisoning
All engines contain carbon monoxide in their exhaust.
Carbon monoxide is a deadly, colorless, tasteless, odorless
gas which may be present even if you do not smell or see
any engine exhaust. Levels of carbon monoxide, which can
be deadly, can be present for days in an enclosed area that
has poor ventilation. Any level of carbon monoxide, if
inhaled, can cause headaches, drowsiness, nausea,
dizziness, confusion and eventually death. If you
experience any of these symptons, seek fresh air and
medical attention immediately.
Preventing Carbon Monoxide Poisoning
•Never run engine indoors.
•Never try to ventilate engine exhaust indoors. Carbon
monoxide can reach dangerous levels very quickly.
•Never run engine outdoors where exhaust fumes may be
pulled into a building.
•Never run engine outdoors in a poorly ventilated area
where the exhaust fumes may be trapped and not easily
taken away. (Examples include: in a large hole or areas
where hills surround your working area.)
•Never run engine in an enclosed or partially enclosed
area. (Examples include: buildings that are enclosed on one
or more sides, under tents, car ports or basements.)
•Always run the engine with the exhaust and muffler
pointed in the direction away from the operator.
•Never point the exhaust muffler towards anyone. People
should always be many feet away from the operation of the
engine and its attachments.
Gasoline Fires or Handling Fuel Safely
Fuel and fuel vapors are highly flammable. Never use fuel
where a spark or flame may be present. Never use fuel
where a potential source of ignition could occur. (Examples
include: hotwater or space heaters, clothes dryer, electric
motors, etc.) Keep flames and sparks away from engine
and fuel to prevent fires. Fuel fires spread very quickly and
are highly explosive.
Prevention of Gasoline Fires
•Never fill your fuel tank with fuel indoors. (Examples
include: basement, garage, barn, shed, house, porch, ice
shelter, etc.)
•Always fill fuel tank outside in a well ventilated area.
•Never remove the fuel cap or add fuel with the engine
running. Stop engine and allow to cool before filling.
•Never drain fuel from engine in an enclosed area.
•Always wipe up excess (spilled) fuel from engine before
starting. Clean up spilled fuel immediately.
•Allow spilled fuel to dry, after wiping and before starting.
•Allow fuel fumes/vapors to escape from the area before
starting engine.
•Test the fuel cap for proper installation before starting
and using engine.
•Always run the engine with fuel cap properly installed on
the engine.
•Replace fuel cap that allows gas to spill or leak.
•Never smoke while refilling engine fuel tank.
•Prevent fire and explosion caused by static electric
discharge. Use only non-metal, portable fuel containers
approved by the Underwriter’s Laboratory (U.L.) or the
American Society for Testing & Materials (ASTM).
•Do not store engine with fuel in fuel tank indoors. Fuel
and fuel vapors are highly explosive.
•Never pour fuel from engine fuel tank.
•Never siphon fuel by mouth to drain fuel tank.
•Always have an adult fill the fuel tank.
•Never allow an adult or anyone under the influence of
drugs or alcohol to fill engine.
•Never allow children to fill the engine.

Page 5
SAFETY
B rns and Fires
The muffler, muffler guard and other parts of the engine
become extremely hot during the operation of the engine.
These parts remain extremely hot after the engine has
stopped.
Prevention of Burns and Fires
•Never remove the muffler guard from the engine.
•Never touch the muffler guard because it is extremely
hot and will cause severe burns.
•Never touch parts of the engine that become hot after
operation.
•Always keep materials and debris away from muffler
guard and other hot parts of the engine to avoid fires.
Steps for W orking on Engine or Attachment
1. Turn off engine switch.
2. Disconnect the spark plug wire from the spark plug.
3. Securely place the disconnected spark plug wire away
from the spark plug and any metal parts. This must always
be done or arcing may occur between spark plug wire and
metal parts.
4. Replace or repair the part on the engine or attachment.
5. Check all parts that were repaired, or removed during
repair, that they are secure and fit correctly.
NOTE: All repair parts must come from the factory.
Never replace parts that are not specifically designed
for the engine or attachment.
6. Replace spark plug wire.
Avoid injury! When working on or replacing parts for
the engine or attachments you must always disconnect
spark plug wire from the spark plug and keep it away
from the spark plug.
CAUTION
Avoid injury! Always wear hearing protection while
operating engine.
CAUTION
Avoid injury! Please do not start your auger until you
have read the previous section of this manual. If you
have read these, follow the steps below to start your
auger.
CAUTION
Preparing Engine for Starting
GAS AND OIL
Quality
To operate the engine you must use a high quality 2-cycle
oil to ensure that the engine operates correctly during the
break-in period and the life of the engine. Use unleaded
regular or unleaded premium gas only.
Mixture
Run ice auger with a 20:1 ratio for the first 20 hours of
operation. After 20 hours of use, mix at a ratio of 25:1. See
charts 1 & 2.
CHART 1
CHART 2
Do Not Alter/Modify Engine or Attachments:
Avoid injury! Never alter or modify the engine from
the factory. Serious injury or death may occur if
engine is modified or altered.
CAUTION
SAG LIO 1OITAR
nollag1secnuo61:02
snollag2secnuo211:02
snollag5secnuo031:02
SAG LIO 1OITAR
nollag1secnuo51:52
snollag2secnuo011:52
snollag5secnuo621:52

Page 6
Mixing F el and Filling F el Tank
Mixing Fuel
1. Fuel must be mixed in a container outside in a well
ventilated area.
2. Fill certified fuel container 1/4 full of recommended fuel.
3. Add recommended amount of 2-cycle oil.
4. Screw container cap on straight and tight.
5. Shake the container to mix fuel and oil.
6. Unscrew cap slowly to vent, add the remainder of fuel
requirements.
7. Wipe away any spilled fuel or oil and allow to evaporate
before moving or transporting.
Avoid injury! Never store engine with fuel in the tank
indoors. Fuel and fuel vapors are highly flammable.
CAUTION
Avoid injury! Never mix fuel and oil directly in engine
fuel tank. Use only non-metal, portable fuel containers
approved by the Underwriter’s Laboratory (U.L.) or the
American Society for Testing & Materials (ASTM).
CAUTION
Avoid injury! An adult must always handle and fill the
engine with fuel.
CAUTION
Avoid injury! Always handle gas in a well ventilated
area, outdoors, away from flames or sparks.
CAUTION
This engine uses a gas/oil mixture. DO NOT run on
straight gas only, engine damage will result.
Filling Fuel Tank
1. Shut-off engine and allow engine to completely cool
before refilling the fuel tank.
2. Move to a well ventilated area, outdoors, away from
flames and sparks.
3. Clean debris from area around the fuel cap.
4. Loosen fuel cap slowly. Place the cap on a clean, dry
surface.
5. Carefully add fuel without spilling.
6. Do not fill gas tank completely full, allow space for fuel
to expand.
7. Immediately replace fuel cap and tighten. Wipe off
spilled fuel and allow to dry before starting engine.
Avoid injury! DO NOT start engine if fuel is spilled.
Wipe off excess fuel and allow to dry. Remove engine
from area to avoid sparks.
CAUTION
OPERATION
Normal Operation
1. The clutch will transfer maximum power after about two
hours of normal operation. During this break-in period clutch
slippage may occur. The clutch should be kept free of oil or
other moisture for efficient operation.
2. Dig holes without placing excessive body weight on the
unit. The auger operates most efficiently with a shaving
action caused by the weight of the unit itself.
3. Never run engine indoors. Exhaust fumes are deadly.
4. Do not use an ice auger in the earth.
5. The ice auger blade protector should be attached to the
auger head when not in use. This will protect the cutting
edge of the ice auger blades.

Page 7
Starting and Stopping Engine
To attach auger to powerhead if not done, align hole in at
top of shaft with output shaft hole. Insert bolt and secure
bolt with provided allen wrench.
NOTE: The ends of the bolt should be flush with auger
collar. Bolt head and thread end should never go
beyond ice collar.
1. Move engine to a well ventilated area, outdoors, to
prevent carbon monoxide poisoning.
2. Move to an area away from flames or sparks, to avoid
ignition of vapors if present.
3. Remove all debris from air cleaner holes and fuel cap to
ensure proper air flow.
4. Turn switch to the ON position.
5. Priming:
•When using the primer bulb, allow the bulb to return
completely to its original position between pushes.
•Choke must be in the OFF position when pushing or using
the primer bulb.
First Start: Starting new engine for first time or after running
out of gas, prime 3 times.
Cold Start: Starting engine after it has been sitting or
stored briefly with fuel in the tank, prime 1 time above 55°
Farenheit or 2 times below 55°Farenheit.
Warm Start: Do not use primer or full choke if engine did
not run out of gas or has not cooled completely. Flooding of
engine will occur.
6. Choke:
•Full choke position is defined by moving the choke lever
as far to the ON position as possible. Half choke is defined
when the choke lever is between ON and OFF.
First Start & Cold Start: After priming, move choke lever to
full choke.
Warm Start: No choke or half choke is needed.
Avoid injury! If auger is mounted to engine, all safety
guards must be securely on to avoid serious injury.
CAUTION
Avoid injury! Starter rope can cause an unanticipated
jerk towards engine. Please follow instructions to avoid
injury.
CAUTION
7. Grasp starter handle and pull out slowly, until it pulls
slightly harder. Without letting it retract, pull rope with a rapid
full arm stroke. Let it return to its original position very
slowly. Repeat this step everytime the starter rope is pulled.
8. Pull recoil until engine fires or runs.
NOTE: If engine fails to start after 5-6 pulls, push primer
1 time and pull starter rope again.
9. After engine starts running, move choke lever to HALF
CHOKE.
10. Run engine for 30 to 45 seconds at half choke position
until engine warms up.
11. Move choke lever to OFF position and move throttle to
desired speed.
12. To stop, flip switch to OFF position.
DO NOT attempt to start engine in the following ways:
·DO NOT use starting fluid.
·DO NOT spray flammable liquids or vapors into air
cleaner, carburetor or spark plug chamber.
·DO NOT remove spark plug and pull on starter rope.
Flammable fuel can spray out & ignite from a spark
from spark plug.
Avoid injury! If engine fails to start after the above
operations, please contact Ardisam, Inc. at 1-800-345-
6007.
CAUTION
Avoid injury! Never leave engine running while
unattended. Turn off after every use.
CAUTION
Avoid injury! Never carry powerhead and auger between
holes while engine is running.
CAUTION
OPERATION

Page 8
To prevent accidental starting:
Avoid injury! Engine must be turned off and cool, and
spark plug wire must be removed from spark plug
before checking and adjusting engine or equipment.
CAUTION
Avoid injury! Engine must be shut-off, cool, and spark
plug wire removed before any repair or maintenance
can be done.
CAUTION
Avoid injury! Temperature of muffler and nearby
areas may exceed 150° F (65° C). Avoid these areas.
CAUTION
Avoid injury! Check auger often for loose nuts and
bolts. Keep these items tightened.
CAUTION
Cooling Fins
•Cooling fins, air inlets and linkages must be free from
any debris before each use.
Air Filters
•Never run engine without air cleaner properly installed.
Added wear and engine failure may occur if air cleaner is
not installed on engine.
•Service air cleaner every 3 months or after 20 hours of
operation. Clean and oil filter daily in extremely dusty
conditions.
Steps for Cleaning Air Filters
1. Wash in warm water with mild soap until dirt and debris
are removed. Press filter when washing, do not twist.
2. Rinse in warm water until soap and dirt are removed.
3. Dry filter by wrapping in a clean cloth and pressing filter
until it is dry.
4. Apply oil to the entire filter.
5. Remove excess oil.
6. Attach the filter and filter cover to the engine.
Spark Plug
•Check spark plug every 50 operating hours.
1. Remove dirt and debris around the spark plug before
removing.
2. Remove spark plug and replace if any of the following
have occured: pitted electrodes, burned electrodes, cracked
porcelain, or deposits around the electrodes.
3. After analysis of the spark plug, install original or a new
spark plug and tighten securely.
NOTE: DO NOT OVERTIGHTEN!
Carburetor
•Never tamper with factory setting of the carburetor.
MAINTENANCE
A ger Maintenance
1. The gear case has 4 oz. of grease installed at the factory.
It is recommended that once a year the gear case be split
and the grease level checked. Add grease only if level of
grease is below top of the gears. DO NOT OVERFILL.
2. Keep all screws, nuts, and bolts tight.
3. For cold weather operation, store the unit in a cool
environment. Transferring the unit from a warm to a cold
place can cause the build up of harmful condensation.
4. Always replace blade protector when power auger is not
in use.
Engine Maintenance
Avoid injury! Never store engine with fuel in the tank
inside a building. Potential sparks may be present for
ignition of fuel and fuel vapors.
CAUTION
Avoid injury! An adult must always do maintenance
and repair on engine and atachments.
CAUTION
Never twist air filters when cleaning. Always press.

Page 9
Avoid injury! To avoid injury or death, never siphon
fuel by mouth.
CAUTION
Long Term Storage
•If your ice auger will not be ran for more than one month,
prepare it for long term storage.
Steps for Long Term Storage
1. Add fuel stabilizer according to manufacturer’s
instructions.
2. Run engine for 10-15 minutes to ensure that the stabilizer
reaches the carburetor.
3. Remove the remainder of the fuel from the gas tank into
an approved fuel container.
4. Remove auger from powerhead and apply a thin layer of
grease to the output shaft (8913).
5. Store auger and powerhead (engine) in a vertical position.
6. Remove all debris from auger and powerhead (engine).
7. Attach blade protector to bottom of auger.
Avoid injury! Never store ice auger with fuel in the fuel
tank inside an enclosed area or building.
CAUTION
TRANSPORTING AND STORAGE
Transporting Yo r Ice A ger
1. Never transport engine inside an enclosed space or
vehicle. Fuel or fuel vapors may ignite causing serious
injury or death.
2. If fuel is present in the fuel tank, transport in an open
vehicle in an upright position.
3. If an enclosed vehicle must be used, remove gas into
an approved red gasoline container. DO NOT siphon by
mouth.
4. Run engine to use up the fuel in the carburetor and fuel
tank. Always run engine in a well ventilated area.
5. Wipe away any spilled fuel from engine and ice auger.
Allow to dry.

Page 10
SERVICE INFORMATION
At Ardisam, we build quality and durability into the design of
our products; but no amount of careful design by us, and
carefulmaintenance byyou, canguarantee arepair-free life
for your auger. Most repairs will be minor, and easily fixed by
following the suggestions in the troubleshooting guide in this
section.
The guide will help you pinpoint the causes of common
problemsand identifyremedies.
Formore complicatedrepairs, youmay wantto relyon your
retailer, an authorized mechanic orArdisam, Inc. (contact
your retailer for a list of authorized mechanics in your area).
A parts catalog is included in this section.
Wewill alwaysbe gladto answerany questionsyou have,or
help you find suitable assistance. To order parts or inquire
about warranty, call or write us at the address found in the
next column under the section ordering repair parts or check
outour website- www.ardisam.com
SERVICE, TROUBLESHOOTING AND REPAIR
ICE POINT REPLACEMENT
1. Remove blade protector and both blades.
2. Remove nut and retaining bolt from point.
3. Using a locking pliers, grasp point and pull out. If holder
doesn’t come out with the point, remove with pliers.
4. With locking pliers, push in new point and holder aligning
bolt hole in point with holes in auger shaft. DO NOT
DAMAGE END OF POINT.
NOTE: When installing holder in auger shaft, edges of
holder may shave off.
5. Insert retaining bolt and tighten with nut.
6. Re-attach both blades and put blade protector back on.
IN CASE OF A SERVICE PROBLEM, DO NOT SEND
UNIT BACK TO RETAILER. CONTACT ARDISAM, INC.
AT 1-800-345-6007.
Avoid injury! Auger blades and point are extremely
sharp. Use caution when removing & replacing.
CAUTION

Page 11
TROUBLESHOOTING
Practice safety at all times. Engine must be turned off
and allowed to cool, and spark plug wire must be
disconnected before attempting any maintenance or
repair.
Problem Possible cause Remedy/Action
Engine will not start
Engine runs rough, floods during
operation
Engine is hard to start
Engine misses or lacks power
Auger turns at idle
Auger turns, but has no power
Auger jumps on ice
Auger cuts slowly
Engine runs, then quits
1. Flip switch to on position
2. Connect spark plug wire to spark plug
1. Clean or replace air cleaner
2. Turn off choke
3. Call factory
1. Drain old fuel and replace with fresh.
Use gas stabilizer at end of season
2. Make sure spark wire is securely
attached to spark plug
3. Clean carburetor, use gas stabilizer,
new gas can
1. Remove and clean
2. Clean or replace
3. Call factory
4. Replace spark plug and adjust gap
1. Adjust idle speed lower
2. Replace both springs
1. Turn off choke after engine is running
2. Call factory
3. Call factory
4. Replace clutch shoes and springs
5. Call factory
1. Buy new blades, or have blades
sharpened at factory
1. Buy new blades, or have blades
sharpened at factory
2. File point, or replace point
1. Check self venting gas cap
1. Power switch off
2. Spark plug wire disconnected
1. Dirty air cleaner
2. Choke partially engaged
3. Carburetor out of adjustment
1. Stale fuel
2. Spark plug wire loose
3. Dirty carburetor
1. Clogged fuel tank
2. Clogged air cleaner
3. Improper carburetor adjustment
4. Spark plug dirty, improper gap, or
wrong type
1. Idle speed too high
2. Broken clutch spring
1. Choke on
2. Carburetor out of adjustment
3. Broken transmission
4. Worn clutch shoes
5. Worn engine lower seal
1. Blades damaged or sharpened
incorrectly
1. Dull blades
2. Damaged point
1. Gas cap not venting
Please include the following information with your order:
1. Part numbers
2. Part description
3. Quantity
4. Model number and serial number
ORDERING REPAIR PARTS
Parts can be obtained from the store where your auger was
purchased or direct from the factory. To order from the
factory, call or write to:
SERVICE, TROUBLESHOOTING AND REPAIR
Ardisam, Inc.
1690 Elm treet, Cumberland, WI 54829
Phone [phone] Fax [phone]
1-800-345-6007
Email [email protected]
www.ardisam.com
CAUTION

Page 12
Z43 & Z51 SHARK ENGINE PARTS LIST

Page 13
Z43 & Z51 SHARK ENGINE PARTS LIST
MINIMUM ORDER ........................................................................... $10.00
POWERHEAD PARTS
Part # Description Qty.
1021 Rocker Switch 1
300401 Fuel Tank Cap 1
300412 Clutch Spring 1
300429 Recoil Plate 1
300430 Recoil Assembly 1
300435 Air Filter 1
300437 Fuel Tank 1
300438 Bolt w/washer, M5 x 25mm 6
300439 Bolt w/washer, M5 x 18mm 9
300442 Clutch Rotor Shoe 2
300444 Support, Fuel Tank 2
300445 Washer, M5 2
300449 Spring Washer, Rotor Shoulder Bolt 2
300450 Shoulder Bolt, Rotor Assembly 2
300454 Intake Base 1
300455 Adapter Plate, Intake Cover 1
300456 Bolt, M5 x 50mm 2
300457 Cover, Air Filter 1
300458 Cover, Intake 1
300462 Rotor Washer 2
300463 Grommet, Engine Shroud 1
300466 Grommet, Fuel Tank 1
300467 Locating Pin 2
300470 Fuel Line Hose & Filter 1
Part # Description Qty.
300471 Bolt, M5 x 12mm 3
300472 Ignition Coil 1
300473 Cover, Muffler 1
300474 Muffler 1
300475 Gasket, Muffler 1
300476 Gasket, Intake 2
300477 Heat Disk 1
300478 Intake Windpipe 1
300479 Gasket, Carburetor 1
300480 Threaded Spacer, Fuel Tank 2
300482 Engine Shroud 1
300483 Cover, Engine Shroud 1
300484 Flywheel, Magneto 1
300485 Air Deflector 1
300486 Carburetor 1
300487 Cover, Engine Mounting 1
300488 Cover, Choke 1
300489 Choke Lever 1
300490 Primer Line Hose 1
300491 Recoil Clutch 1
300492 Nut, M6 2
300493 Stud Bolt, M6 x 62mm 2
BM6A Spark Plug 1

Page 14
Z43 & Z51 SHARK PARTS LIST

Page 15
Z43 & Z51 SHARK PARTS LIST
POWERHEAD PARTS
Part # Description Qty.
1023 Bolt, M6 x 1 x 16mm 4
8912 44T Gear 1
8913 Output Shaft, 7/8" 1
8915 Dowel Pin, 1/4" x 1/2", hardened steel 1
8919 Gasket 1
8922 Ball Bearing 3
8923 Ball Bearing 1
8924 Snap Ring 2
8929 Bolt-SHCS, 1/4-20 x 1-1/2" 2
8931F Bolt-SHCS, 1/4-20 x 2" 4
8939 Gear Case Bottom 1
8945 Hand Throttle Control, Right 1
8946 Hand Throttle Control, Left 1
8947 Trigger 1
8948 Spring, Throttle Control 1
8952 HandleBar 1
8954 Hand Throttle Control Complete 1
(includes 8945, 8946, 8947, 8948, 8960, 8961, 8972)
8956 Throttle Cable 1
8960 Screw, #4 x 5/8” 2
8961 Scre, #6 x 1 1
8964 Screw, 10 x 1 1/4” 1
8965 Nut, #10 Top Loc 1
8966 Adapter Ring 1
8972 Washer, 3mm 1
9814MM Pinion Gear, 7 tooth threaded 1
67435 Washer, 1/4 SAE 4
200131 Gear Case Top 1
300406 Ball Bearing 1
300409 Spacer-Drum 1
300414 Clutch Drum 1
300421 Gear, 48T left hand thread 1
300426 12T, Pinion, Left Hand Threads 1
300443 Gas Engine, 43cc 1
3004517 Gas Engine, 51.7cc 1
LBL43 Decal, Z43 Shark, serialized 1
LBL51 Decal, Z51 Shark, serialized 1
LBL432 Decal, Z43 Shark, handlebar 1
LBL512 Decal, Z51 Shark, handlebar 1
LBLBPE Decal, Blade Protector, Eskimo 1
LBLESKS Decal, Eskimo oval, auger stem 1
WL14 Washer, 1/4” Spring 4
300497 Transmission Complete, 25:1 1
8909B Bolt, 1/4 x 1 1/4” 4
POWER AUGER PARTS
Part # Description Qty.
232A Blade Protector, fits 6”-8" quantum auger(incl. 8651) 1
233A Blade Protector, fits 9” & 10" quantum (incl. 8651) 1
2320A Blade Protector, fits 6”-8” turbo auger 1
8651 Strap, Blade Protector 1
8955 Auger Bolt-SHCS, 3/8-16 x 1-1/4" 1
(auger to powerhead)
53606 Nut, #10, nyloc 1
63387 Lockwasher, 5mm 4
90129 Point Replacement Assembly 1
(includes 53606, 90136, 90165, 90166)
90136 Bolt, #10-24 x 1-1/4” stainless 1
90165 Point Holder 1
90166 Point 1
BB8 Ice Blades, 8" TurboCut 2
(includes 63387, IB5810)
BR8N Ice Auger, 8" Turbo 1
IB5810 Bolt, 5mm x 0.8 x 10mm, (turbo ice blade to auger) 4
IB5816 Bolt, 5mm x 0.8 x 16mm, (ice blade to auger) 4
IN58 Nut, 5mm x 0.8 nyloc, (ice blade to auger) 4
QB8 Ice Blades, 8" Quantum, set of two 1
(includes IB5816, IN58)
QB9 Ice Blades, 9" Quantum, set of two 1
(includes IB5816, IN58)
QB10 Ice Blades, 10" Quantum, set of two 1
(includes IB5816, IN58)
QT8N Ice Auger, 8" Quantum 1
QT9N Ice Auger, 9" Quantum 1
QT10N Ice Auger, 10" Quantum 1
ACCESSORIES
EXT6 Depth Extension, 6"
EXT12 Depth Extension, 12"
EXT18 Depth Extension, 18"
MINIMUM ORDER ........................................................................... $10.00

Ardisam, Inc.
1690 Elm Street, Cumberland, Wisconsin 54829
Phone [phone] •Fax [phone]
1-800-345-6007
Email [email protected]
www.ardisam.com