Argo DD User manual

EN
IT
INSTALLATION
INSTRUCTIONS
MANUALE
D’INSTALLAZIONE
NOTICE
D’INSTALLATION
INSTALLATIONS-
ANLEITUNGEN
INSTRUCCIONES
DE INSTALACIÓN
INSTRUÇÕES DE
INSTALAÇÃO
FR
Air conditioner without outdoor unit
Climatizzatore senza unità esterna
Climatiseur sans unité extérieure
Klimagerät ohne Ausseneinheit
Acondicionador de aire sin unidad exterior
Ar condicionado sem unidade externa
37.4255.175.00 06/2018
DE
ES
PT

2
CONTENTS
EN
1 - Generalities ...........................................3
2 - Presentation ..........................................4
3 - Installation............................................6
4 - Match between remote controller and unit .................11
5 - Special settings ......................................12
6 - Electrical wiring diagrams...............................14
REGULATION (EU) No. 517/2014 - F-GAS
The unit contains R410A, a fluorinated greenhouse gas
with a global warming potential (GWP) of 2087.50.
Do not release R410A into the atmosphere.
R410A: 0,70 kg / 1,46 Tonn. CO2
Power Supply:
220 - 240 V ~ 50 Hz
This symbol refers to a hazard or unsafe practice which can result in severe personal
injury or death.
This symbol refers to a hazard or unsafe practice which can result in personal injury
or product or property damage.
WARNING
CAUTION
IMPORTANT!
Please read before installation
This air conditioner meets strict safety and operating standards.
For the installer or service person, it is important to install or service the air conditioner so that it operates safely and
efficiently.
Recommendations
•Thepersonnelresponsibleforreceivingtheairconditionermustconductavisualinspectioninordertoidentifyall
damage to which it may have been subjected during transport: refrigerating circuit, electrical cabinet, chassis and
cabinet.
•Operateasfollowswhenopeningthepackagingbox:
1. removetheboxfromthetop;
2. removethecardboardcoverandcorners;
3. removethecardboardsheetwiththegrilles,thehangingbracketandthebottompanel;
4. remove the front panel with care and store it in a safe place in order to avoid damaging or scratching it;
the panel must be mounted on the unit only after installation;
5. proceed with the installation of the unit.
For safe installation and trouble-free operation, you must:
•Carefullyreadthisinstructionbookletbeforebeginning.
•Followeachinstallationorrepairstepexactlyasshown.
•Observealllocal,stateandnationalelectrical(andsafety)codes.
•Paycloseattentiontoallwarningandcautionnoticesgiveninthismanual.
CAUTION
Be careful not to damage the front panel during handling !
DECLARATION OF CONFORMITY
This product is marked as it satisfies Directives:
– LVD no. 2014/35/EU (Standard: EN60335-2-40:2003 (incl. Corr.:2006) + A11:2004 + A12:2005 + A13:2012 +
A1:2006 + A2:2009 with EN 60335-1:2012 (incl. Corr.:2014) + A11:2014).
–EMCno.2014/30/EU(Standard:EN55014-1:2006+A1:2009+A2:2011;EN55014-2:1997+A1:2001+A2:2008;
EN61000-3-2:2014;EN61000-3-3:2013).
– RoHS2 n.2011/65/EU + 2015/863/EU amending ANNEx II.
This declaration will become void in case of misuse and/or non-observance though partial of manufacturer’s
installation and/or operating instructions.

3
EN
COOLING
OUTDOOR TEMPERATURE 43°C D.B.
ROOM TEMPERATURE 32°C D.B./23°C W.B.
OUTDOOR TEMPERATURE -15°C D.B.
ROOM TEMPERATURE 10°C D.B./6°C W.B.
HEATING
OUTDOOR TEMPERATURE 24°C D.B./18°C W.B.
ROOM TEMPERATURE 27°C D.B.
OUTDOOR TEMPERATURE -15°C D.B.
INDOOR ROOM 10°C D.B.
MAxIMUM CONDITIONS
MINIMUM CONDITIONS
MAxIMUM CONDITIONS
MINIMUM CONDITIONS
OPERATING LIMITS
•Supplytheunitwithadedicatedelectricalline.
•Makeinstalltheunitbyqualifiedpersonnel.
•Beforeinstallation,checkthatthevoltageoftheelectricsupplyinyourhomeorofficeisthesameasthevoltage
shown on the nameplate.
•Theinstallationofadouble-poleswitch,protectedby10Afusesofthedelayedtype,upstreamtheelectricitywall
socket, is recommended.
•Makesurethatcircuitbreakers,fuses,etc,areofsufficientcapacitytohandleastart-upcurrentof20A(generallyless
then 1 second) - ONLY FOR ON/FF VERSION
•WARNING!
The air conditioner is provided with a time-guard system, which does not allow re-starting of compressor until after 3
minutes from a previous stop.
If necessary, get help
These instructions are all you need for most installation sites and maintenance conditions.
Ifyourequirehelpforaspecialproblem,contactoursale/serviceoutletoryourcertifieddealerforadditionalinstructions.
In case of improper installation
The manufacturer shall in no way be responsible for improper installation or maintenance service, including failure to
follow the instructions in this document.
ELECTRICAL SHOCK CAN CAUSE SEVERE PERSONAL INJURY OR DEATH.
ONLY QUALIFIED, ExPERIENCED ELECTRICIANS SHOULD ATTEMPT TO WIRE THIS SYSTEM.
•Donotsupplypowertotheunituntilallwiringarecompletedorreconnectedandchecked,toensurethegrounding.
•Highlydangerouselectricalvoltagesareusedinthissystem.Carefullyrefertothewiringdiagramandtheseinstructions
when wiring.
 Improperconnectionsandinadequategroundingcancauseaccidentalinjuryanddeath.
•Ground the unit following local electrical codes.
•TheYellow/Greenwirecannotbeusedforanyconnectiondifferentfromthegroundconnection.
•Connectallwiringtightly.Loosewiringmaycauseoverheatingatconnectionpointsandapossiblefirehazard.
•Donotallowwiringtotouchtherefrigeranttubing,compressor,oranymovingpartsofthefan.
•Donotusemulticorecablewhenwiringthepowersupplyandcontrollines.Useseparatecablesforeachtypeofline.
When transporting
Be careful when picking up and moving the unit. Get a partner to help, and bend your knees when lifting to reduce strain
on your back. Sharp edges or thin aluminium fins on the unit can cut your fingers.
Move the unit only after removing the front panel and the bottom panel.
When installing
Make sure the wall is strong enough to hold the unit weight. It may be necessary to build a strong wooden or metal
frame to provide added support.
Donotmountthefrontpaneland/orthebottompanelbeforefixingtheunittothewall.
When wiring
WARNING
1 - GENERALITIES
OPERATING CONDITIONS SPECIAL PRECAUTIONS
•Cleanonlywithneutraldetergents.
•Donotplaceobjectsontheunit.
•Donotpourliquidsontheunit.

4
EN
1. Wireless remote control unit
2. Signaling lamps an d receiver
3. Supply air deflector
4. Bottom air intake grille (removable)
5. Air filter
6. Electric cable with plug
7. Air inlet hole with fan
8. Air outlet hole
9. Service cap for condensate discharge
10. Operation button: to access the button it is
necessary to remove the bottom panel
2 - PRESENTATION
2
3
4
5
7
1
2.1 - DESCRIPTION OF THE PARTS
6
8
9
10

5
EN
1. PLASTIC SHEET (2pcs.)
2. ExTERNAL GRILLES (2pcs.)
3. INTERNAL GRILLES (2pcs.)
4. TENSION BARS (2pcs.)
5. FULL SCALE DIAGRAM (1pcs.)
6. RAWL PLUGS + SCREWS
7. REMOTE CONTROL UNIT (1pcs.)
8. BATTERIES FOR REMOTE CONTROL (2pcs.)
9. GASKETS (4pcs.)
10. HANGING BRACKET
11. CONDENSATE DRAINAGE PIPE WITH
INSULATION
12. JUMPER FOR PCB (4pz.)
1. Receiver : it receives signals transmitted from the
remote control.
2. TIMER lamp: This lamp lights up when the air
conditioner is being controlled by the timer.
3. STANDBY lamp: This lamp lights up when the air
conditioner is waiting to start or the desired temperature
has been reached.
4. OPERATION lamp: This lamp lights up during
operation.
The OFF position does not disconnect the power. Use
the main power switch to turn off power completely.
WARNING
NOTES
lIt is possible to set the air conditioner in order to let
the OPERATION, TIMER and STANDBY lamps always
OFF, even during operation.
Press contemporary the IFEEL and FAN buttons on
the remote control unit for more then 5 seconds.
Repeat the same procedure to set again the normal
operation conditions.
lIn case of troubleshooting the air conditioner
diagnostic system activates the lamps accordingly,
even if they are set to OFF. See paragraph
TROUBLESHOOTING for further details.
lWhen the air conditioner is OFF lights are off to
reduce power consumption.
2.2 - SIGNALING LAMPS
1
34
2
7
8
51
2
3
4
6
9
2.3 - ACCESSORIES SUPPLIED WITH THE UNIT 10
11
12

6
EN
2.4 - DIMENSIONS AND WEIGHT
Model Weight (kg)
DD 46
DD DCI 43
205
594
1013
min. 800
min. 300
min. 300
2000
min. 300
250 250
3 - INSTALLATION
3.1 - INSTALLATION SITE SELECTION
AVOID
•Proximitytoheatsources,exhaustfans.
•Proximitytocombustiblematerials.
•Direct sunlight.
•Locationswheretheunitcouldbesplashedwithwater
or affected by dampness or humidity (i.e. in laundries).
•Unsteadylocationsthatwillcausenoiseorpossible
waterleakage.
•To make holes in areas where electrical wiring or
conduits are located.
IMPORTANT NOTES
•The wall must be a perimeter one.
•Selectasufficientlystrongwalltosupporttheweightof
the unit.
•Fixtheunitataminimumheightof30cm.
•Leave a minimum operation and maintenance area
around the unit.(See figure).
•Make sure that there are no obstacles around the unit
affecting the free circulation of air.
•Avoid installing the unit with the air flow directly toward
passerby people, electric appliances or heat sources.
250 250
min. 300
LOW WALL INSTALLATION HIGH WALL INSTALLATION

CAUTION
After the selection of the installation site, according
to the above mentioned points, be sure not to make
holes in areas where electrical wiring or conduits are
located, damaging them.
Make sure that there are no obstacles in the conduits
inside the wall affecting the free circulation of the
external air. The unit must be kept at a minimum
distance of 80 cm from any wall or obstacle.
Level
Full scale
diagram
Mill
7
EN
- Applyatthewallthefullscalediagram,fixandlevelit.
- Drill the two holes Ø 162 mm and the hole Ø 35 mm for
the condensate drainage toward the outside (assure a
positive slope toward the outside).
- Cut to size the supplied plastic sheets in order to obtain,
by rolling them, two tubes of the right size (it is necessary
to measure the thickness of the wall and subtract 70 mm
in order to leave enough space to the grilles).
3.2 - HOW TO INSTALL THE UNIT
CAUTION
Do not mount the front panel and the bottom panel
until installation is complete.
1013
A
B
CC
D
594
463
355 205
FULL SCALE DIAGRAM
A Holes for rawl plugs Ø 9 mm
B Hole for electrical connection Ø 30 mm
C Holes for air Ø 162 mm
DHole for condensate discharge Ø 35 mm

8
- Insert in the two holes the obtained plastic tubes.
-Fixthetwoanti-intrusiongrillesandthetwoexternal
grilles with the blades toward the bottom using wall rawl
plugs and screws.
-Incaseitisnotpossibletofixthetwoexternalgrilles
directly at the wall, hook the two grilles to the internal
ones (3) using the supplied tension bars, as follows:
 a)Bendthem,fixthehookofthespring,insertthem
inside the tube and open them toward the outside.
b) Choose the proper hook of the tension bar in order
to lengthen the spring of 15-20 mm and hook it to
the internal grille.
 c)Eliminatetheexceedingpartofthetensionbarcutting
it near the hooking points.
- Apply the supplied gaskets (9) around the holes on the
back side of the unit.
Spring
hook
- In case of very thin walls (less than 10 cm) it is necessary
to mount the internal anti-intrusion grilles on the back
of the unit applying the gaskets (9) around the grilles.
Unscrewthescrewsonthebackoftheunitandfixthe
grilles using the same screws.
 Thetubeandtheexternalgrilleswillnotbeused.
CAUTION
The manufacturer assumes no
responsibilities if this safety
instruction is not observed.
INSIDE OUTSIDE
EN
9
93
3
3
9

9
WARNING!Thesuppliedplasticsheetcanbeusedforwall
thicknessupto50cm;inspecialcases(i.e.installations
in a garret) it can be necessary to utilise longer tubes.
Themaximumallowablelengthis2m.Youcangotoany
building material retailer, buy the plastic tube of the same
diameter (ø160 mm), of the proper length and cover it
outside with insulating material (thickness: about 3-4 cm).
-Fixthehangingbrackettothewallintheposition
indicated on the full scale diagram.
 Thequantityandthetypeofrawlplugsdependsonthe
consistenceofthewall;donotletanyspacebetween
the panel and the wall.
- Hang up the unit at the bracket by simultaneously
inserting the condensate drainage pipe into the wall hole.
- Predispose a condensate drainage toward the outside
making a hole Ø 35 mm as indicated on the full scale
diagram. Assure always a positive slope of at least
1cm/m.
3.2 - ELECTRICAL CONNECTION
Theairconditionerisequippedwithapowercablewith
plug (the electrical connection of the unit is Y type with
cablepreparedinaspecialway;anyreplacementmust
only be carried out by the authorized Service Center).
Before connecting the air conditioner, be sure that:
• The voltage of the mains power supply is the same as
the voltage shown on the nameplate.
• The power supply line has a ground connection and
itiscorrectlysizedformaximumelectricalinputof
the air conditioner (minimum cable cross-section:
1,5mm2).
• The air conditioner is powered only through a socket
compatible with the plug supplied.
Main switch for disconnection from the supply line must
have a contact separation in all poles that provides
full disconnection under category III overvoltage
conditions.
Connect the unit inserting the plug in the power socket.
ELECTRICAL CONNECTION THROUGH A CABLE BUILT
INTO THE WALL
It is possible to proceed with the electrical connection
through a cable built into the wall as indicated in the full
scale diagram (recommended connection for installation
of the unit in the upper part of the wall).
• Disconnect the main switch before making the elec-
trical connection.
• Disconnect the power cable with plug from the ter-
minal block.
• Connect a similar cable, pass it through the appro-
priate hole on the full scale diagram (cut the rubber
grommet) and connect it to the cable built into the
wall.
EN
CAUTION
Plastic tubes ø 160mm
Insulation

10
EN
3.3 - HOW TO MOUNT THE FRONT PANEL AND THE
BOTTOM PANEL WITH FILTER
Mountthefrontpaneltakingcarenottoscratchit;operate
as follows:
- Connect the receiver cable to the connector (1).
- Grasp the panel, keeping it slightly raised relative to the
unit and bring it into place by inserting it first right and
then left. (See figure)
-Slideitdowninordertofixthethreelateralhooks(2)to
the structure.
- Loosen the screws of the two lower safety hooks (2),
move them outwards and re-tighten them again to
secure the panel, so that it is not accidentally removable.
- At this point mount the bottom panel with filter (see
figure) as follows:
- Place the panel vertically and insert it under the unit on
the back so that the four hooks (3) fit into place.
-Rotatethepanelupwardstofixthefrontparttothe
structurethroughthecentralhooks(4);helpyourself
by pressing the central hooks with two fingers.
CAUTION
ON/OFF CONTACT CONNECTION
TheairconditionerisequippedwithanON/OFFcontact
(in very low voltage, to be connected to a clean contact, not
intension);Whenopeningthecontact,theairconditioner
is in stand-by.
Throughthiscontactitispossibletoconnectanexternal
device that inhibits the operation of the air conditioner,
asforexample:windowopeningcontact,remoteon/off,
infrared presence sensor, enabling badge, etc.
It is recommended to use a double insulation cable.
The unit is supplied with a pre-installed jumper between
2polesoftheterminalblock;removethejumperbefore
connecting the remote ON / OFF contact.
Once the installation is finished, verify the correct operation
of the air conditioner.
3
3
3
3
4
2
4
3
2
1
2
BOTTOM PANEL WITH FILTER

11
4 - MATCH BETWEEN REMOTE CONTROLLER AND UNIT
If there are more units installed in the same room, it is possible to combine each remote controller with a unit in order
to avoid interference, by operating as follows:
• Disconnect the power of the unit.
• Remove the batteries from the remote control unit.
• Set the microswitches (see table).
• Insert the batteries in the remote control unit.
• Switch on the unit.
At this point the unit starts operating with the new address.
1
FACTORY STATE
1=OFF 2=OFF 3= OFF 4=OFF
5=ON 6=ON SW1: 3=OFF 4=OFF
2
1=ON 2=OFF 3=OFF 4=OFF
5=ON 6=ON SW1: 3=ON 4=OFF
3
1=OFF 2=ON 3=OFF 4=OFF
5=ON 6=ON SW1: 3=OFF 4=ON
4
1=ON 2=ON 3=OFF 4=OFF
5=ON 6=ON SW1: 3=ON 4=ON
REMOTE CONTROL UNIT PCB
UNIT
REMOTE CONTROL
UNIT
EN
PCB

12
5 - SPECIAL SETTINGS
SPECIAL SETTINGS THROUGH JUMPER
JP1:
Internal use. Do not change factory setting.
JP2 / JP3:
JP2 JP3 Description
Open Open Normal operation (factory setting)
Closed Open Setting “cooling only”.
If the heating mode is selected, the “wrong mode” error will be generated (see
auto-diagnosis table).
Open Closed Setting “heating only”.
If the cooling or dehumidifying mode is selected, the “wrong mode” error will
be generated (see auto-diagnosis table).
Closed Closed Automatic setting “cooling only” or “heating only” according to the outside
temperature.
Above 24°C the air conditioner is set to “cooling only”, under 20°C it is set to
“heating only”, between 20°C and 24°C it is left free.
If a mode that is opposite to the air conditioner setting is selected, the “wrong
mode” error will be generated (see auto-diagnosis table).
SPECIAL SETTINGS THROUGH REMOTE CONTROL UNIT
Limitation of the desired temperature range
The air conditioner is set by default to operate with a desired temperature range between 10°C and 32°C.
To limit this range between 16°C and 24°C in heating mode and between 22°C and 28°C in cooling or dehumidifying
mode, follow the procedure below:
1. Hold down the “FILTER” button for more than 7 seconds and release it. A number will appear on the remote control
screen.
2. Press the + or - keys until the number 12 is displayed.
3. Hold down the “FILTER” button for more than 7 seconds and release it by pointing the remote control at the air
conditioning receiver. An acoustic confirmation of 4 consecutive “beeps” will confirm the successful setting.
Note: on the remote control it will still be possible to select a temperature outside the range but the air conditioner will
limit it internally.
To disable the limitation of the desired temperature range, repeat the same procedure. An acoustic confirmation of 2
consecutive “beeps” will confirm that the original setting has been reset.
High wall installation setting
In case of high wall installation of the air conditioner, activate this setting to take into account the temperature stratification
during the heating mode.
Through this setting it is possible to select the temperature difference between the lower part of the room and the position
of the air conditioner in order to calibrate the reading of the air probe on the air conditioner. By default this difference is
set to 0°C (low wall installation). In case of high wall installation, it is recommended to set a difference of 3°C.
To change this parameter, follow the procedure below:
1. Hold down the “FILTER” button for more than 7 seconds and release it. A number will appear on the remote control
screen.
2. Press the + or - keys until the number 10 is displayed.
3. Hold down the “FILTER” button for more than 7 seconds and release it by pointing the remote control at the air
conditioning receiver.
4. Hold down again the “FILTER” button for more than 7 seconds and release it. The number 10 will appear on the
remote control screen.
5. Pressthe+or-keystoselectthedesireddifference°C(max10°C).
6. Hold down the “FILTER” button for more than 7 seconds and release it by pointing the remote control at the air
conditioning receiver.
EN

13
During the heating mode, the air conditioner will now operate with the new calibration of the air probe.
Nota: this setting has no effect when I Feel is selected. In this case the air conditioner will operate with the remote
control air probe.
ATM mode setting
It is possible to set the air conditioner to operate automatically without a remote control so that it maintains the room
temperature between 18°C and 24°C. A typical application is that of installation within ATMs (cash machine) of banks. In
this mode it is not necessary to set the desired temperature or operating mode, but it will all be managed automatically
by the air conditioner.
To activate this mode, follow the procedure below:
1. Press and hold the “FILTER” button (symbol) for more than 7 seconds. A number will appear on the remote control
screen.
2. Press the + or - keys until the number 11 is displayed.
3. Hold down the “FILTER” button for more than 7 seconds and release it by pointing the remote control at the air
conditioning receiver. An acoustic confirmation of 4 consecutive “beeps” will confirm the successful setting.
Nota: 60 seconds after activating ATM mode the remote control is disabled.
To disable ATM mode, follow the procedure below:
1. Disconnect the power of the air conditioner
2. Wait for 1 minute
3. Re-connect power to the air conditioner
4. Within 60 seconds (before the remote control is disabled again), repeat the procedure above. An acoustic confirmation
of 2 consecutive “beeps” will confirm that the original setting has been reset.
Display setting : Celsius degrees / Fahrenheit degrees
TheremotecontrolissetbydefaulttodisplaythetemperatureexpressedinCelsiusdegrees.
To change the temperature display from Celsius degrees to Fahrenheit degrees (and vice versa), follow the procedure
below:
1. Hold down the “FILTER” button for more than 7 seconds and release it. A number will appear on the remote control
screen.
2. Press the + or - keys until the number 77 is displayed.
3. Hold down the “FILTER” button for more than 7 seconds and release it. The temperature will now be displayed on
the remote control screen with the new setting.
Note: if you remove the batteries from the remote control, the default display is reset.
Factory settings’ reset
To reset the factory settings, follow the procedure below:
1. Hold down the “FILTER” button for more than 7 seconds and release it. A number will appear on the remote control
screen.
2. Press the + or - keys until the number 0 is displayed.
3. Hold down the “FILTER” button for more than 7 seconds and release it by pointing the remote control at the air
conditioning receiver. An acoustic confirmation of 2 consecutive “beeps” will confirm the correct reset of the factory
settings.
Note: to reset the temperature display in Celsius degrees, remove and replace the batteries of the remote control unit.
EN

14
5 - ELECTRICAL WIRING DIAGRAMS - SCHEMI ELETTRICI - SCHÉMAS ÉLECTRIQUES - ELEKTRISCHE
ANSCHLUSSPLÄNE - ESQUEMAS ELÉCTRICOS

15

S.A.C. - Printed in italy
Via Alfeno Varo, 35 - 25020 Alfianello - BS - Italy
Tel.+390331755111-Fax+390331755501
www.argoclima.com