Argos Elega 432/5217 User manual

Simple Assembly Instructions - Please keep for future reference
IMPORTANT
1. Read these instructions carefully and
familiarise yourself with the procedure
before assembling the unit.
2. Check that you have all the component
parts following the list on the back
cover and familiarise yourself with
each part before proceeding.
3. Take all the fittings out of the plastic bag
and separate them into their groups.
4. Ensure you have enough space to lay out
all the parts before assembly.
Three Head Street Lamp
Components
Fittings
5. To avoid scratching it is recommended
that you assemble the unit on a soft
level surface.
11-08
A1 x Head
1 x Top Tube
B
1 x Middle Tube
C
1 x Base
D
F3 x Lamp Head
G1 x Wires H3 x Lamp Top
(Fitted to Lamp Head)
A3 x Peg B3 x Spring C3 x Screw D3 x Big Nut
E6 x Screw F6 x Small Nut G3 x Plastic Washer
(Fitted to Lamp Head)
H3 x Screw
(Fitted to Lamp Head)
J6 x Screw K1 x Tool L1 x Tool M1 x Tool
(Fitted to Head)
E3 x Lamp

Assembly Instructions Assembly Instructions
Stage 1 – Fitting the Pole HeadStage 1 – Fitting the Pole Head
BROWN or RED
BLUE or BLACK
GREEN /YELLOW
fig. 1
Fixing Screw
Top
fig. 2 Top
Wires
BROWN or RED
BLUE or BLACK
GREEN /YELLOW
Lamp
BROWN or RED
BLUE or BLACK
GREEN /YELLOW
Top
CAUTION:
Glass is very fragile. Handle it
carefully and keep away from
children.
fig. 3
fig. 4 fig. 6
fig. 5
1. Loosen the Fixing Screws on
Head A. Then remove the Top
from the Pole Head.
See fig. 1.
4. Feed the wires from Lamp E
through Head A .
See fig. 4.
3. Remove Screws Jfrom Head A.
See fig. 4.
5. Use Screws Jto fix Lamp E onto
Head A.
See fig. 4.
6. Connect the Lamp wires to the
Lamp Connection Block .
See fig. 5 and 6.
7. Refit the Top to Head A.
8. Repeat Step 1-9 to assemble the
other two Lamps E.
CAUTION:
We strongly recommend this
light is fitted by a Qualified
Electrician. If you are in any
doubt please ask the retailer
where you purchased this
2. Connect Wires G to the Lamp
Connection Block.
See fig. 2 and 3.
IMPORTANT:
Ensure the electricity is
switched off at the mains before
installing or maintaining the
light fixture.
A
AG
G
A
E
J
J
G
G
A
Lamp Connection Block
Lamp Connection Block

Assembly Instructions Assembly Instructions
Stage 2 – Fitting the BulbsStage 2 – Fitting the Bulbs
F
H
F
H
F
fig. 7
fig. 8
fig. 9
fig. 10
fig. 11
1. Screw a Bulb (E27 Max. 60W, not
included) into the unit.
See fig. 7.
2. Unscrew Screw H, Plastic
Washer Gand Lamp Top H from
Lamp Head F.
See fig. 8.
3. Use Screw Hand Plastic Washer
Gto fix Lamp Top H onto Lamp
Head F.
See fig. 9.
4. Use Screws Eand Small Nuts F
to fix Lamp Head F onto the unit.
See fig. 10.
5. Repeat Steps 1-4 to assemble the
other two Lamp Heads.
See fig. 11.
E27 Max. 60W
H
G
H
G
IMPORTANT:
Ensure the electricity is
switched off at the mains before
installing or maintaining the
light fixture.
E
F

Assembly Instructions Assembly Instructions
Stage 4 – Fitting the BaseStage 3 – Fitting the Tubes
NOTE: It would be useful to ask
someone to help you at this
stage.
NOTE: Ensure the unit is secure
before attempting move it. BROWN or RED
BLUE or BLACK
GREEN /YELLOW
Mains
BROWN or RED
BLUE or BLACK
GREEN /YELLOW
NOTE: It would be useful to ask
someone to help you at this
stage.
fig. 12
fig. 13
fig. 14
Fixing Screw
fig. 15
fig. 17
1. Screw Top Tube B onto Middle
Tube C.
See fig. 12.
2. Carefully pass Wires G through
Top Tube B and Middle Tube C.
See fig. 13.
3. Loosen the Fixing Screws on Pole
Head A . Then carefully fit the
Pole Head onto the Top Tube.
Secure the Pole Head using the
fixing screws.
See fig. 13 and 14.
1. Fit Pegs Ainto holes in the
triangular plate in Base D.
See fig. 15.
2. Set Pegs Ainto a secure base
such as concrete, where it is to
be located. Run a mains cable
connected to a light switch to the
lamp, bringing it up though the
centre of pegs. Use appropriate
sleeving to protect the cable.
Ensure the concrete is set and
the pegs are secure before
proceeding.
See fig. 16.
3. Pass Wires G through Base D.
Then connect Wires G to the
mains.
See fig. 17.
G
B
C
AD
A
G
IMPORTANT:
Ensure the electricity is
switched off at the mains before
installing or maintaining the
light fixture.
Mains Connection Block
Mains
Connection
Block
fig. 16
Main Wires
A
B
C

1. Switch off the mains power supply.
2. Before replacing the bulb, allow it
to cool down for at least 10
minutes.
3. Never touch the bulb with your
fingers directly, cover it with a cloth.
4. Loosen the bulb and remove it from
the lamp.
5. Replace a new bulb with same
voltage and wattage.
Assembly Instructions Assembly Instructions
Stage 5 – Bulb ReplacementStage 4 – Fitting the Base
1. Switch off the mains power supply.
2. Let the bulb cool down before
replacing it - allow at least 10
minutes.
3. Never touch the bulb with your
fingers directly, cover it with a cloth.
4. Loosen the bulb and remove it from
the lamp.
5. Replace with a new bulb of the
same voltage and wattage.
Technical DataCaution
Model No.
Input Voltage
Max. Wattage
Bulb
432/5217
220-240V~, 50Hz
3 x Max.60W
Max. 60W E27 230V-240V~
1. Connect to 230V/240V~, 50Hz.
2. If in doubt about fitting this product. Please
consult a suitably qualified electrician.
3. The temperature of the spot lamp rises very
quickly. Do not touch the metal parts or glass
of the spot lamp after the light is turned on.
4. Never allow the light beam to point directly onto
the ceiling.
D
E
C
D
NOTE: Ensure the unit is secure
before use. fig. 18
fig. 19
fig. 20
4. Use Big Nuts Dand Spring
Washers Bto fix Base D onto
Pegs A.
See fig. 18.
5. Use Screws Cto fix Middle Tube
Conto Base D.
See fig. 19. A
D
B
C